• The korean journal of orthodontics
• /
• v.41 no.1
• /
• pp.6-15
• /
• 2011

Objective: The aim of this study was to evaluate the biomechanical aspects of peri-implant bone upon root contact of orthodontic microimplant. Methods: Axisymmetric finite element modeling scheme was used to analyze the compressive strength of the orthodontic microimplant (Absoanchor SH1312-7, Dentos Inc., Daegu, Korea) placed into inter-radicular bone covered by 1 mm thick cortical bone, with its apical tip contacting adjacent root surface. A stepwise analysis technique was adopted to simulate the response of peri-implant bone. Areas of the bone that were subject to higher stresses than the maximum compressive strength (in case of cancellous bone) or threshold stress of 54.8MPa, which was assumed to impair the physiological remodeling of cortical bone, were removed from the FE mesh in a stepwise manner. For comparison, a control model was analyzed which simulated normal orthodontic force of 5 N at the head of the microimplant. Results: Stresses in cancellous bone were high enough to cause mechanical failure across its entire thickness. Stresses in cortical bone were more likely to cause resorptive bone remodeling than mechanical failure. The overloaded zone, initially located at the lower part of cortical plate, proliferated upward in a positive feedback mode, unaffected by stress redistribution, until the whole thickness was engaged. Conclusions: Stresses induced around a microimplant by root contact may lead to a irreversible loss of microimplant stability.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.10
• /
• pp.1042-1048
• /
• 2008

Disc brake noise is an important customer satisfaction and warranty issue for many manufacturers as indicated by technical literature regarding the subject coming from Motor Company. This research describes results of a study to assess disk brake squeal propensity using finite element methods and optimal technique (Kriging). In this study, finite element analysis has been performed to determine likely modes of brake squeal. This paper deals with friction-induced vibration of disc brake system under contact friction coefficient. A linear, finite element model to represent the floating caliper disc brake system is proposed. The complex eigen-values are used to investigate the dynamic stability and in order to verify simulations which are based on the FEM model. In this paper, Kriging from among the meta-modeling techniques is proposed for an optimal design scheme to reduce the brake squeal noise.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1131-1135
• /
• 2004

In the virtual environment, force feedback to the human operator makes virtual experiences more realistic. However, the force feedback using active actuators such as motors can make the system active and sometimes unstable. To ensure the safe operation and enhance the haptic feeling, stability should be guaranteed. Both motors and brakes are commonly used for haptic device. A brake can generate a torque only against its rotation, but it is intrinsically stable. Consequently, motors and brakes are complementing each other. In this research, a two degree-of-freedom (DOF) haptic device equipped with both motors and brakes has been developed to provide better haptic effects. Each DOF is actuated by a pair of motor and brake. Modeling of the environment and the control method are needed to utilize both actuators. For various haptic effects, contact with the virtual wall and representation of friction effect are extensively investigated in this paper. It is shown that the hybrid haptic system is more suited to some applications than the motor-based active haptic system.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2008.04a
• /
• pp.172-176
• /
• 2008

In this paper, three dimensional linear conforming variable-finite elements are presented with the aid of a smoothed integration (a class of stabilized conforming nodal integration), for mnltiscale mechanics problems. These elements meet the desirable properties of an interpolation such as the Kronecker delta condition, the partition of unity condition and the positiveness of interpolation function. The necessary condition of linear exactness is fully relaxed by employing the smoothed integration, which renders us to meet the linear exactness in a straightforward manner. This novel element description extend the category of the conventional finite elements space to ration type function space and give the flexibility on the number of nodes of element which are fixed in the conventional finite elements. Several examples are provided to show the convergence and the accuracy of the proposed elements, and to demonstrate their potential with emphasis on the multiscale mechanics problems such as global/local analysis, nonmatching contact problems, and modeling of composite material with defects.

• Architectural research
• /
• v.12 no.2
• /
• pp.93-98
• /
• 2010

This paper describes a numerical method for estimating the elastic moduli of cement paste. The cement paste is modeled as a unit cell which consists of three components: the unhydrated cement grain, the gel, and the capillary pore. In the unit cell, the volume fractions of the constituents are quantified using a single kinetic function calculating the degree of hydration. The elastic moduli of cement paste are calculated from the total displacements of constituents when a uniform pressure is applied to the gel contact area. The cement paste is assumed to be a homogenous isotropic matrix. Numerical simulations were conducted through the finite element analysis of the three-dimensional periodic unit cell. The model predictions are compared with experimental results. The predicted trends are in good agreement with experimental observations. This approach and some of the results might also be relevant for other technical applications.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.6
• /
• pp.1539-1544
• /
• 1995

Copper blow test to measure the forging capability of 35 ton counterblow hammer and upset of plasticine on the model hammer to investigate the change of the blow efficiency during the forging process have been performed together with finite element analyses of these experiments. The blow efficiency of the hammer has been found to be dependent on the friction and on the contact area between the die and the workpiece. The effects of the volume and the aspect ratio of the billet have not been found. Inferring from the experimental results and Schey's empirical formula on the forging load, we expect that the efficiency also varies with the flow stress of the workpiece material and with the shape complexity of the forging product.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.6
• /
• pp.1411-1421
• /
• 1995

A rigid visco-plastic finite element method has been developed for modeling superplastic forming processes. The optimum pressure-time relationship for a target strain rate and thickness distributions was predicted using two-node line element based on membrane approximation for plane strain and axisymmetric condition. Analysis of superplastic forming was carried out using the developed program and the numerical results were compared to the values available in the literature for plane strain problems. For description of the contact between the dies and sheet, the direct projection method was applied to the complicated problem and the validity of the scheme was tested. Experiments for the various geometries such as hemisphere and cone were performed with the developed forming machine using the calculated optimum pressure-time curves. Comparison between analysis and experiments showed good agreement.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.6
• /
• pp.66-72
• /
• 2006

In this paper, an analytical investigation on the track separation mechanism for tracked excavator was studied. Relative motions of track links, sprocket, idler and support rollers are very important in the driving of an excavator The interference and friction between each components lead to noise and vibration. And also this has a great influence on the life for tracked excavator. RecurDyn program was used for the three dimensional modeling of the track assembly. Investigating the interference between sprocket and track links, the mechanism of the track separation was analyzed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.1
• /
• pp.205-215
• /
• 2001

In this study, modeling and analysis procedure for the dynamic analysis of a high mobility tracked vehicle system were studied. The vehicle model used in this investigation is assumed to be consist of two kinematically decoupled subsystems. The chassis subsystem consists of chassis frame, sprocket, support rollers, road wheels, idler wheel, road wheel arms and idle wheel arm, while the track subsystem is represented as a closed kinematic chain consisting of track links and end connectors interconnected by revolute joints with bushing. Nonlinear contact force module describing the interaction between track link, and sprocket, idler wheel, road wheel, support roller, ground was used. The effects of road wheel arms and idler wheel arm due to tension adjuster are also considered.

• Proceedings of the KIPE Conference
• /
• 1996.06a
• /
• pp.63-66
• /
• 1996

An micro model for the power insulated Gate Bipolar Transistor(IGBT) is developed. The model consistently described the IGBT steady-state current-voltage characteristics and switching transient current and voltage waveform for all loading conditions. The model is based on the equivalent circuit of a MOSFET with supplies the base current to a low-gain, high-level injection, bipolar transistor with its base virtual contact at the collector and of the base. Model results are compared with measured turn-on and turn-off waveform for different drive, load, and feedback circuits.