• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.62 no.3
• /
• pp.139-144
• /
• 2013

In Korea, where most of the sites are narrow in space and their earth resistivity is relatively high, the spaces between grounding conductors are likely to be designed narrow in order to lower ground resistance and dangerous voltage below to the permitted safety values. In addition, ground nets are in the shape of square or rectangle depending on the location and size of the facilities and ground contact area, and inner conductors are laid out in grids like the pattern of nets. Nevertheless, with the existing designs, the marginal voltage for safety gets higher as the area is extended further outside, in comparison with that of inner mesh grounding, thus causing much difficulty maintaining them equipotential, and there exist limits in the burial, grounding grid design considering the dangerous voltage of muti-layered model in the constrained sites, was studied.

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.813-815
• /
• 1998

In order to analyse the degradation process of epoxy/glass fiber for outdoor condition, FRP laminate was exposed to the wavelength of ultraviolet rays and evaluated by comparing contact angle, surface resistivity, surface potential decay, and ESCA spectrum respectively. Finally, We can conclude that the degradation phenomena on the surface of epoxy composites are dominated by the induction of ester and carboxyl groups.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.435-438
• /
• 2002

In this paper, the effect of surface tension, wettability, flow rate of contaminants with varying surfactant content and frequency of applied voltage on the tracking breakdown of epoxy insulating materials were investigated. As the flow rate of contaminant is increased, the surface resistivity is decreased, and the leakage current is increased, the time to tracking breakdown is decreased. It is found that time to tracking breakdown depends on the surface tension of contaminant, that is difference of wettability And as the frequency of applied voltage is increased, time to tracking breakdown decreased.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1457-1459
• /
• 2001

This paper deals with the change of surface Potential decay, surface resistivity, contact an91e and XPS of ultraviolet-treated PET films. From the experimental results on the surface Potential decay of UV degraded-samples, it was found that the accumulation of charge is decreased and the surface potential decay time is shortened. Also, from the result of XPS, it was found that the changes affected by the surface degradation of PET film were caused by the generation of carboxyl groups through the chain decomposition and recombination with oxygen molecules in the air.

• Proceedings of the Optical Society of Korea Conference
• /
• 2000.02a
• /
• pp.30-31
• /
• 2000

400DPI LED array was fabricated by using reactive ion etching(RIE) method. Material of fabricated LED array was used the GaP for green light emitting and had a homojunction structure. Each cells of emitting area in the LED array were defined with RIE etching for electrical isolation between cells. Electrodes were formed on each cells to emit independently. Ohmic contact resistivity was approximate 1.2$\times$10$^{5}$ $\Omega$/$\textrm{cm}^2$ and 1.26$\times$10$^{5}$ $\Omega$/$\textrm{cm}^2$ using isothermal annealing at 38$0^{\circ}C$ and 43$0^{\circ}C$. Emitting intensity of each etmitting cell was 1.65 cd/$m^2$.

• Journal of Sensor Science and Technology
• /
• v.20 no.3
• /
• pp.145-150
• /
• 2011

In this paper, we designed a tunable microstrip patch antenna using RF MEMS switches. The design and simulation of the antenna were performed using a high frequency structure simulator(HFSS). The antenna was designed for use in the ISM band and either operates at 2.4 GHz or 5.7 GHz achieving -10 dB return-loss bandwidths of 20 MHz and 180 MHz, respectively. In order to obtain high efficiency and improve the ease of integration, a high resistivity silicon(HRS) wafer on a glass substrate was used for the antenna. The antenna achieved high gains: 8 dB at 5.7 GHz and 1 dB at 2.4 GHz. The RF MEMS DC contact switches were simulated and analyzed using ANSYS software.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.9
• /
• pp.114-120
• /
• 1994

We have been successfully fabricated the low nois HEMT device with AlGaAs and GaAs structure. The epitazial layer with n-type AlgaAs and undoped GaAs was grown by molecular beam epitaxy(MBE) system. Ohmic resistivity of the ource and drain contact is below 5${\times}10^{6}{\Omega}{\cdot}cm^{2}$ by the rapid thermal annealing (RTA) process. The ideality factor of the Schottky gate is below 1.6 and the gate material was Ti/Pt/Au. The HEMTs with 0.25$\mu$m-long and 200$\mu$m-wide gates have exhibited a noise figure of 0.65dB with associated gain of 9dB at 12GHz, and a transconductance of 208mS/mm.

• Electrical & Electronic Materials
• /
• v.10 no.8
• /
• pp.770-777
• /
• 1997

Some polymer materials including epoxy resin are being instead of porcelain for outdoor insulating materials such as insulators bushings cable terminators and surge arrester housing. And the largest problem to be overcomed is the tracking and erosion of the outdoor polymer material brought about by dry band arcing during prolonged exposure to contaminations. In this paper the effect of surface tension wettability flow rate of contaminants with varying surfactant content and frequency of applied voltage on the tracking breakdown of epoxy insulating materials were investigated. As the flow rate of contaminant is increased the surface resistivity is decreased and the leakage current is increased the time to tracking breakdown is decreased. It is found that time to tracking breakdown depends on the surface tension of contaminant that is difference of wettability. And as the frequency of applied voltage is increased time to tracking breakdown decreased.

• Carbon letters
• /
• v.1 no.1
• /
• pp.1-5
• /
• 2000

The effect of surface free energy on the positive temperature coefficient (PTC) of carbon black/thermoplastic resin composites was investigated. The thermoplastic resins such as EVA, LDPE, LLDPE and HDPE were used with the addition of 30 wt.% of the carbon black. The surface free energy of the composites was studied in the context of two-liquid contact angle measurements, i.e., deionized water and diiodomethane. It was observed that the resistivity on PTC composites Was greatly increased near the crystalline melting temperature, due to the thermal expansion of polymeric matrix. From the experimental results, it was proposed that the decrease of surface free energy induced by interactions between carbon black surfaces and polymer chains is an important factor to the fabrication of a PTC composite made of carbon black and polymeric matrix.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.853-854
• /
• 2006

Warm compaction powder metallurgy was used to produce a $Ti_3SiC_2$ particulate reinforced Cu matrix composite. Fabrication parameters and warm compaction behaviors of Cu powder were studied. Based on the optimized fabrication parameters a Cu-based electrical contact material was prepared. Results showed that in expend of some electrical conductivity, addition of $Ti_3SiC_2$ particulate increased the hardness, wear resistivity and anti-friction ability of the sintered Cu-base material.