• Current Photovoltaic Research
• /
• v.10 no.4
• /
• pp.95-100
• /
• 2022

Solar cell is a device that converts photon energy into electrical energy. Therefore, absorption of solar spectrum light is one of the most important characteristics to design the solar cell structures. Various methods have emerged to reduce optical losses, such as textured surfaces, back contact solar cells, anti-reflection layers. Here, the anti-reflection coating (ARC) layer is typically utilized whose refractive index value is between air (~1) and silicon (~4) such as SiN_x layer (~1.9). This research is to print a material called polydimethylsiloxane (PDMS) to form a double anti-reflection layer. Light with wavelength in the range of 0.3 to 1.2 micrometers does not share a wavelength with solar cells. It is confirmed that the refractive index of PDMS (~1.4) is an ARC layer which decreases the reflectance of light absorption region on typical p-type solar cells with SiN_x layer surface. Optimized PDMS printing with analyzing optical property for cell structure can be the effective way against outer effects by encapsulation.

• Tribology and Lubricants
• /
• v.39 no.6
• /
• pp.250-255
• /
• 2023

This study applies various surface patterns to minimize material loss in construction equipment that is subject to severe wear due to sand, such as the wear-resistant steel plates of dump trucks or the teeth of excavators. The relationship between surface morphology and wear behavior is investigated using PLA+ polymer to observe the effect of the surface pattern. Five types of samples - smooth, concave, convex, wavy concave, and wavy convex designs - are created using a 3D printer. A wear experiment is conducted for a duration of 3 h using 6.5 kg of abrasive particles. The mass loss of the samples after the experiment is measured to assess the extent of wear. Additionally, the surface morphology of the samples before and after the experiment is analyzed using SEM and confocal microscopy. The study results reveal that the smooth design exhibits the highest wear loss, whereas the concave and wavy concave designs show relatively lower wear loss. The convex and wavy convex designs exhibit varying contact areas with the abrasive particles depending on the surface pattern, resulting in different levels of wear. Furthermore, a comparison between the experimental results and DEM simulations confirms the observed wear trends. This study reveals the relationship between wear damage according to surface pattern shape and is expected to be of substantial help in the analysis of wear and tear on agricultural and heavy equipment.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.44 no.2
• /
• pp.141-147
• /
• 2024

In this study, micro CT images were used to confirm the tensile fracture strength according to the pore distribution characteristics of 3D printed concrete. Unlike general specimens, concrete structures printed by 3D printing techniques have the direction of pores (voids) depending on the stacking direction and the presence of filaments contact surfaces. Accordingly, the pore distribution of 3D printed concrete specimens was analyzed through quantitative and qualitative methods, and the tensile strength by direction was analyzed through a finite element technique. It was confirmed that the pores inside the 3D printed specimen had directionality, resulting in their anisotropic behavior. This study aims to analyze the characteristics of 3D concrete printing specimen and correlate them with simulation-based mechanical properties to improve performance of 3D printed material and structure.

• Journal of the Korean Ceramic Society
• /
• v.39 no.2
• /
• pp.120-125
• /
• 2002

AC powder EL devices were fabricated by screen printing method with the dielectric materials in insulating layer and the electrical resistivity of rear electrode. Brightness and current density were measured at voltage range of 50∼300 $V_{rms}$ to estimate optoelectrical properties of AC powder EL devices, respectively. Frequency generator was used as system producing frequency and voltage of a sine wave. Brightness and current density were measured by luminometer and multimeter. Also, dielectric constant for dielectric layer was measured by impedance analyser after preparing thick film. Dielectric constant was improved with amount of $TiO_2$ to $BaTiO_3$ powder. By applying such a process to dielectric layer of low cost AC powder EL device, brightness was improved to 50 cd/$m^2$ at similar current density. Dielectric constant $BaTiO_3$ powder by solution combustion process is better than commercial $BaTiO_3$ powder. By applying to that of low power consumption AC powder EL device, brightness was improved to 85 cd/$m^2$. Brightness of AC powder EL device was relatively decreased by control of electrical resistivity of rear electrode, current density was also decreased.

• Current Photovoltaic Research
• /
• v.9 no.3
• /
• pp.75-83
• /
• 2021

The tunnel oxide passivated contact (TOPCon) structure got more consideration for development of high performance solar cells by the introduction of a tunnel oxide layer between the substrate and poly-Si is best for attaining interface passivation. The quality of passivation of the tunnel oxide layer clearly depends on the bond of SiO in the tunnel oxide layer, which is affected by the subsequent annealing and the tunnel oxide layer was formed in the suboxide region (SiO, Si₂O, Si₂O₃) at the interface with the substrate. In the suboxide region, an oxygen-rich bond is formed as a result of subsequent annealing that also improves the quality of passivation. To control the surface morphology, annealing profile, and acceleration rate, an oxide tunnel junction structure with a passivation characteristic of 700 mV or more (V_oc) on a p-type wafer could achieved. The quality of passivation of samples subjected to RTP annealing at temperatures above 900℃ declined rapidly. To improve the quality of passivation of the tunnel oxide layer, the physical properties and thermal stability of the thin layer must be considered. TOPCon silicon solar cell has a boron diffused front emitter, a tunnel-SiO_x/n⁺-poly-Si/SiN_x:H structure at the rear side, and screen-printed electrodes on both sides. The saturation currents J_o of this structure on polished surface is 1.3 fA/cm² and for textured silicon surfaces is 3.7 fA/cm² before printing the silver contacts. After printing the Ag contacts, the J_o of this structure increases to 50.7 fA/cm² on textured silicon surfaces, which is still manageably less for metal contacts. This structure was applied to TOPCon solar cells, resulting in a median efficiency of 23.91%, and a highest efficiency of 24.58%, independently. The conversion efficiency of interdigitated back-contact solar cells has reached up to 26% by enhancing the optoelectrical properties for both-sides-contacted of the cells.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.21 no.3
• /
• pp.156-161
• /
• 2011

Objectives: Tetrahydrofuran (THF) is a colorless, water-miscible organic liquid with low viscosity at standard temperature and pressure. THF has been used as a solvent and a precursor for various syntheses of polymers. However, THF is known to irritate to the eyes, skin and mucus membranes. Overexposure by inhalation, ingestion or skin contact may produce nausea, dizziness, headaches, respiratory irritation and possible skin burns. The purpose of this study is to evaluate of the worker exposure and characteristics of workers in the workplaces that use or manufacture THF. Methods: Sixteen factories in Korea, which manufacture or use THF, were selected for this study and a total of 130 air samples including 104 time-weighted average (TWA) samples and 26 short-term exposure limit (STEL) samples, were collected. Air samples were collected with charcoal tube (100mg/50mg) and analyzed by gas chromatograph/flame ionization detector(GC/FID). Results: The TWA concentration of THF was 16.05ppm (GM) at PS script printing, 2.32ppm (GM) at PVC stabilizer, 1.03ppm (GM) at Lithium triethylborohydride, 0.63ppm (GM) at Polytetramethylene ether glycol(PTMEG), 0.42ppm (GM) at Manufacturing THF, 0.13ppm (GM) at Glue and 0.12ppm (GM) at synthetic rubber/resins. Two out of sampes for PS script printing exceeded 50ppm as 8-hour exposure limit of MOEL. The short term exposure to THF was 54.77ppm (GM) at PS script printing, 17.10ppm (GM) at PTMEG, 13.76ppm (GM) at Manufacturing THF, 2.86ppm (GM) at Lithium triethylborohydride, 0.87ppm (GM) at synthetic rubber/resins and 0.13ppm (GM) Glue. We found that the highest exposure process for both the TWA and STEL samples was PS script process. Two samples exceeded 100ppm as short term exposure limit of Ministry of Employment and Labor(MOEL). Conclusions: Characteristic of STEL concentration for THF is considerably different from TWA concentration in workplaces because workers could exposure high concentration of THF in a moment when they work irregularly schedule. So exposure controls for momentary works have to be prepared, and considered the skin absorption and inhale of THF.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.3
• /
• pp.71-76
• /
• 2012

A chip interconnection technology for smart fabrics was investigated by using flip-chip bonding of SnBi low-temperature solder. A fabric substrate with a Cu leadframe could be successfully fabricated with transferring a Cu leadframe from a carrier film to a fabric by hot-pressing at $130^{\circ}C$. A chip specimen with SnBi solder bumps was formed by screen printing of SnBi solder paste and was connected to the Cu leadframe of the fabric substrate by flip-chip bonding at $180^{\circ}C$ for 60 sec. The average contact resistance of the SnBi flip-chip joint of the smart fabric was measured as $9m{\Omega}$.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.04a
• /
• pp.105-110
• /
• 2011

The doping procedure in crystalline silicon solar cell fabrication usually contains oxygen injection during drive-in process and removal of phosphorous silicate glass(PSG). In this paper, we studied the effect of oxygen injection and PSG on conversion efficiency of solar cell. The mono crystalline silicon wafers with $156{\times}156mm^2$, $200{\mu}m$, $0.5-3.0{\Omega}{\cdot}cm$ and p-type were used. After etching $7{\mu}m$ of the surface to form the pyramidal structure, the P(phosphorous) was injected into silicon wafer using diffusion furnace to make the emitter layer. After then, the silicon nitride was deposited by the PECVD with 80 nm thickness and 2.1 refractive index. The silver and aluminium electrodes for front and back sheet, respectively, were formed by screen-printing method, followed by firing in 400-425-450-550-$880^{\circ}C$ five-zone temperature conditions to make the ohmic contact. Solar cells with four different types were fabricated with/without oxygen injection and PSG removal. Solar cell that injected oxygen during the drive-in process and removed PSG after doping process showed the 17.9 % conversion efficiency which is best in this study. This solar cells showed $35.5mA/cm^2$ of the current density, 632 mV of the open circuit voltage and 79.5 % of the fill factor.

• Journal of the Korean Solar Energy Society
• /
• v.31 no.1
• /
• pp.37-43
• /
• 2011

In this paper, the optimized doping condition of crystalline silicon solar cells with $156{\times}156\;mm^2$ area was studied. To optimize the drive-in temperature in the doping process, the other conditions except variable drive-in temperature were fixed. These conditions were obtained in previous studies. After etching$7\;{\mu}m$ of the surface to form the pyramidal structure, the silicon nitride deposited by the PECVD had 75~80nm thickness and 2 to 2.1 for a refractive index. The silver and aluminium electrodes for front and back sheet, respectively, were formed by screen-printing method, followed by firing in 400-425-450-550-$850^{\circ}C$ five-zone temperature conditions to make the ohmic contact. Drive-in temperature was changed in range of $830^{\circ}C$ to $890^{\circ}C$to obtain the sheet resistance $30{\sim}70\;{\Omega}/{\box}$ with $10\;\Omega}/{\box}$ intervals. Solar cell made in $890^{\circ}C$ as the drive-in temperature revealed 17.1% conversion efficiency which is best in this study. This solar cells showed $34.4\;mA/cm^2$ of the current density, 627 mV of the open circuit voltage and 79.3% of the fill factor.

• Journal of Conservation Science
• /
• v.33 no.1
• /
• pp.43-49
• /
• 2017

The ancient paper document we chose as a case study for our research is "One Hundred Poets of the Tang Dynasty", which is housed in the Ryukoku University Library. The purpose of this research is to introduce a method to analyze the surface roughness and microstructure at a high resolution. In addition, we attempt to quantitatively measure the surface unevenness of the types and curve structure. We used a tridimensional digital microscopy as a non-contact and a non-destructive method to study ancient cultural paper. The information contained in the paper may be lost in the process of applying strong pressure to clean and lining or press. However, this microscopic measurement method can non-destructively analyze a large amount of data in old printed books. Moreover, it enables observing them directly with reflected light. Therefore, this method may be useful for collecting printed information remaining on the surface of the paper.