• Journal of the Society of Naval Architects of Korea
• /
• v.60 no.3
• /
• pp.186-192
• /
• 2023

According to the regulation on the pollution of the marine environment, SOx emission from ships has to be reduced. A SOx scrubbing system installed in a funnel of a ship is considered in order to reduce SOx emission. A scrubbing layer with a porous material is present in the funnel to increase the contact area between exhaust gas and water. In this study, experiments on the pressure drop characteristics in the scrubbing layer are conducted to investigate the effect of the scrubber on the engine load. The pressure drop according to flow rate of air instead of exhaust gas was measured for fillers such as sphere, pall ring and saddle in the scrubbing layer. First of all, porosity is experimentally measured for the three types of filler and it is confirmed that the porosity of the saddle-type filler was the largest. The pressure drop according to the change in air flow rate was measured for the three types of fillers in the scrubbing layer. As a result, the pressure drop was the smallest in the scrubbing layer with the saddle-type filler which has the largest porosity. In addition, the effect of spraying water flowing counter flow against air flow is experimentally examined. It is known that the pressure drop is increased because the air flow space is reduced when water is sprayed. In the case of the saddle, the pressure drop is about 1.5 to 2 times greater than that when only air flows at the optimum exhaust gas-water injection ratio.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.6
• /
• pp.704-711
• /
• 2023

This paper discusses the control method of BLDC(Brushless Direct Current) motor that has similar electrical characteristics with DC motor but has improved its lifespan and reliability. The BLDC motor can improve durability and speed stability by using rotor position information to eliminate commutators that require mechanical contact with DC motors. In this study, a controller for a DC motor was designed based on the fact that the current in the windings of a BLDC motor is a square-wave current like the current flowing in the armature of a DC motor. Next, the designed controller was applied to a 3-phase BLDC motor to confirm the effectiveness of the controller. In detail, a single-phase DC motor with electrical parameter values of a three-phase BLDC motor was modeled and a PI controller for motor speed control was designed by applying the root locus method to the derived system. The speed control simulation of the DC motor was performed to confirm the validity of the controller, and the same controller was applied to the speed control of the 3-phase BLDC motor implemented in MATLAB. From the simulation, similar results of the DC motor were obtained in the 3 phase BLDC motor and confirmed the usefulness of the proposed control scheme.

• Tunnel and Underground Space
• /
• v.33 no.6
• /
• pp.483-494
• /
• 2023

Measurement of the physical properties of rocks or minerals is an important factor in determining the distribution of the underground medium as well as mineral resource investigations. Resistivity and induced polarization, which are widely used in Korea, are methods for measuring electrical properties, which are representative properties of obtaining subsurface information. In order to precisely analyze the exploration data obtained from various sites, it is important to accurately measure the material properties. Electrical properties of rock is measured using two-electrode or four-electrode method. Compared to the four-electrode method, the two-electrode method is generally used because it is very easy to contact the sample and the electrode, but there is a problem in that the impedance of the electrode and the sample is measured together. In this study, the time-domain the induced polarization effects were measured using the 2-electrode method and the 4-electrode method for artificial samples mixed with graphite and cement having induced polarization characteristics, and the results were compared. Although the 4-electrode method has difficulties in installing potential electrodes, it was confirmed that it is effective in measuring electrical properties because it can reduce the problem caused by the impedance of potential electrodes compared to the 2-electrode method.

• Journal of the Korean Geotechnical Society
• /
• v.40 no.1
• /
• pp.5-14
• /
• 2024

PHC piles demonstrate superior resistance to compression and bending moments, and their factory-based production enhances quality assurance and management processes. Despite these advantages that have resulted in widespread use in civil engineering and construction projects, the design process frequently relies on empirical formulas or N-values to estimate the soil-pile friction, which is crucial for bearing capacity, and this reliance underscores a significant lack of experimental validation. In addition, environmental factors, e.g., the pH levels in groundwater and the effects of seawater, are commonly not considered. Thus, this study investigates the influence of vibrating machine foundations on PHC pile models in consideration of the effects of varying pH conditions. Concrete model piles were subjected to a one-month conditioning period in different pH environments (acidic, neutral, and alkaline) and under the influence of seawater. Subsequent repeated direct shear tests were performed on the pile-soil interface, and the disturbed state concept was employed to derive parameters that effectively quantify the dynamic behavior of this interface. The results revealed a descending order of shear stress in neutral, acidic, and alkaline conditions, with the pH-influenced samples exhibiting a more pronounced reduction in shear stress than those affected by seawater.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.37 no.2
• /
• pp.208-214
• /
• 2024

This reports the electrical properties of single-crystal β-gallium oxide (β-Ga₂O₃) vertical Schottky barrier diodes (SBDs) with a different guard ring structure. The vertical Schottky barrier diodes (V-SBDs) were fabricated with two types guard ring structures, one is with metal deposited on the Al₂O₃ passivation layer (film guard ring: FGR) and the other is with vias formed in the Al₂O₃ passivation layer to allow the metal to contact the Ga₂O₃ surface (metal guard ring: MGR). The forward current values of FGR and MGR V-SBD are 955 mA and 666 mA at 9 V, respectively, and the specific on-resistance (R_on,sp) is 5.9 mΩ·cm² and 29 mΩ·cm². The series resistance (R_s) in the nonlinear section extracted using Cheung's formula was 6 Ω, 4.8 Ω for FGR V-SBD, 10.7 Ω, 6.7 Ω for MGR V-SBD, respectively, and the breakdown voltage was 528 V for FGR V-SBD and 358 V for MGR V-SBD. Degradation of electrical characteristics of the MGR V-SBD can be attributed to the increased reverse leakage current caused by the guard ring structure, and it is expected that the electrical performance can be improved by preventing premature leakage current when an appropriate reverse voltage is applied to the guard ring area. On the other hand, FGR V-SBD shows overall better electrical properties than MGR V-SBD because Al₂O₃ was widely deposited on the Ga₂O₃ surface, which prevent leakage current on the Ga₂O₃ surface.

• Journal of the Korean Wood Science and Technology
• /
• v.52 no.3
• /
• pp.221-233
• /
• 2024

Lignin, a prominent constituent of woody biomass, is abundant in nature, cost-effective, and contains various functional groups, including hydroxyl groups. Owing to these characteristics, they have the potential to replace petroleum-based polyols in the polyurethane industry, offering a solution to environmental problems linked to resource depletion and CO₂ emissions. However, the structural complexity and low reactivity of lignin present challenges for its direct application in polyurethane materials. In this study, Kraft lignin (KL), a representative technical lignin, was fractionated with ethanol, an eco-friendly solvent, and mixed with conventional polyols in varying proportions to produce polyurethane films. The results of ethanol fractionation showed that the polydispersity of ethanol-soluble lignin (ESL) decreased from 3.71 to 2.72 and the hydroxyl content of ESL increased from 4.20 mmol/g to 5.49 mmol/g. Consequently, the polyurethane prepared by adding ESL was superior to the KL-based film, exhibiting improved miscibility with petrochemical-based polyols and reactivity with isocyanate groups. Consequently, the films using ESL as the polyol exhibited reduced shrinkage and a more uniform structure. Optical microscope and scanning electron microscope observations confirmed that lignin aggregation was lower in polyurethane with ESL than in that with KL. When the hydrophobicity of the samples was measured using the water contact angle, the addition of ESL resulted in higher hydrophobicity. In addition, as the amount of ESL added increased, an increase of 7.4% in the residual char was observed, and a 4.04% increase in Tmax the thermal stability of the produced polyurethane was effectively improved.

• Composites Research
• /
• v.37 no.5
• /
• pp.427-433
• /
• 2024

As the automotive industry transitions from internal combustion engine vehicles (ICEV) to battery electric vehicles (BEVs), customers are becoming increasingly aware of and demanding solutions to squeak noises, especially from audio, video, and navigation (AVN) components. These noises occur under relatively high load and low speed conditions and cannot be reproduced on commercial friction test equipment. Therefore, a new friction testing machine was developed and evaluated in this study. This machine is a pin-on-disk type tribometer that can set up the squeak noises test conditions for AVN component materials and quantitatively measure acceleration, sound pressure, and displacement due to friction. The developed equipment was evaluated through two types of tests: the noise evaluation of well-known contact pairs, and the comparison test of the friction coefficient repeatability. The test results confirm that the developed test machine can be utilized for the evaluation of the squeak noise. In addition, it was also found that the characteristics of squeak noise in high load and low speed conditions can be defined as groan noise. Moreover, displacement, friction force, acceleration was found to have a relationship with sound amplitude with relation of more than R² = 0.75. Acceleration can be a key parameter to predict squeak noise, since it has a strong correlation (R² = 0.94) in high load low speed conditions.

• The Journal of the Petrological Society of Korea
• /
• v.19 no.2
• /
• pp.141-156
• /
• 2010

Dokdo Island, Korea, is located in the East Sea belonging to back arc basin. In this study we examined petrology and geochemistry of massive tuffaceous breccia (MTB) from Dongdo (Eastern islet) and Seodo(Western islet), the two largest islands of Dokdo. Field studies and chemical analysis distinguish the MTB in Dongdo and Seodo. The Dongdo MTB (DMTB) is exposed up to 50 m on the ocean cliff and it has dominant basalt and trachybasalt with moderate amount of trachyte and scoria. On the other hand, Seodo MTB (SMTB), which is preserved between trachyte dike and trachyandesite, is composed of roughly equal amounts of basalt, trachybasalt and trachyte. The location of the islets were related to the source vent having in contact with underlying trachyte lava and differential pyroclastic deposits made them different characteristics. According to trace element analysis of trachytic volcanic clasts, the Ba concentration ranges from 66 to 103 ppm and Sr varies from 44 to 56 ppm in DMTB. However, Br and Sr in SMTB correspondingly showed relatively wide ranges: Br 785-1259 ppm and Sr 466-1230 ppm. These differential trends between DMTB and SMTB, along with the difference in P and Ti, indicate that the crystallization of alkali feldspar, feldspathoid, biotite, apatite and titanium took place differently. Nevertheless, DMTB and SMTB are similar in REE patterns and they are correspondingly characterized by high LREE, low HREE and similar $(La/Yb)_N$ values with 23.9-40.2 in DMTB and 27.4-32.9 in SMTB. These patterns suggest that Dongdo and Seodo might be originated from coeval magma suites. Dokdo island shows high concentrations of Ba, K and Rb. These signatures mark a result attributed to the mantle upwelling because the magma derived from the asthenosphere was metasomatized with subduction-related fluids.

• Journal of the Korean Home Economics Association
• /
• v.38 no.5
• /
• pp.137-152
• /
• 2000

North Korean fugitives is one of various nominations referring to the North Koreans who have secretly crossed the territorial border of their country. It is a new terminology that huts gained wider usage in our society as we entered the 1990s. North Koreans list various motives for escaping their county, such as food shortage and disillusionment of belief in the system. Most of the forced repatriation of North Korean escapees takes place in China. The purpose of this study examines the family knife of female fugitives from North Korea in order to provide pertinent alterntives which are needed to secure basic human right of the female fugitives and enable them to keep stability of their family lives and to adapt themselves into new socio-cultural circumstances in China. For this, the preliminary survey performed to examine the demographic characteristics on the female fugitives; to find out the incentives and channels of their escape out of North Korea; to investigate what types of family life and family relationship they manage in China; to grasp their problems and need of family life in adaptation into Chinese society. The specific questions for grasping the general characteristics of the female fugitives are composed of age, education level residential district in North Korea. In order to find out main causes and influential factors of their escape from North Korea, the following questions are included: what the most important incentives and motives are; the frequency of escape; and whether they discuss their escape with their family or not. The questions to find out their present actual life situations in China are about difficult things to adjust in China, family life, relationship with husband, and their conversational diction, the degree of their mastering the chinese language, the degree of their adaptation to chinese way of living, and so forth, which reveal to what extent they are adapted themselves to new cultural situation in China. This study collected the data through face-to-face personal interview from July to October, 1999 Yenben province along the China-North Korea border. Data from 202 female fugitives were used in final analysis. This study uses the SAS PC program for windows, Ver, 6.12 to analyze the data such as the distribution of frequency, percentage, mean and so on. The results from this analysis are follows; the most principal motive of North Korean women's escape to china is to eat to live because of famine. Concerning the year when the fugitives escape from North Korea, all of the interviewees haute escaped since 1990. After escape their continual contact with their family in North Korea, 81.7% of the respondent have not been in touch with their family. The main reasons for their not contacting with their family in North Korea are that it is not helpful although they contacts with their family. Female fugitives from North Korea have difficulties in life. They have rather stable relationship to their husband, but they have experienced difficulties in other aspects of family life. Their main difficulties are largely from their relationships to husbands'family members, and from the problems relate to their family in North Korea, and their children. Based on this study, further research has to present supportive policies that help North Korean female escapees live without being deprived and protect their human rights. And the development of practical program to help their efficient social adaptation has to be continued without stop together.

• Economic and Environmental Geology
• /
• v.45 no.4
• /
• pp.351-363
• /
• 2012

In order to develop the evaluation techniques for the potential sulfide ore reserves, the relationships between the modal vol.%, grain sizes and textural characteristics of the constituent minerals (e.g., sulfides, oxides and skarn minerals) and the Spectral Induced Polarization (SIP) phase differences are examined for the nine rock cores collected from the Gagok Pb-Zn skarn deposit. The Gagok Pb-Zn skarn deposit occurs mainly along the intrusive contact between the Cretaceous granitic rocks and Cambrian Myobong slate and Pungchon limestone. The nine rock cores have been grouped into three showing distinctive SIP phase differences: the highest (Group I), intermediate (Group II) and lowest (Group III). In relation with the modal vol.% of minerals, Group I is characterized by higher pyrrhotite (25-38 vol.%) and amphibole (40-55 vol.%); Group II by intermediate pyrrhotite (7-13 vol.%) and higher garnet (44-68 vol.%); and lower pyrrhotite (1-7 vol.%) and higher pyroxene (24-66 vol.%) stand for Group III. Furthermore, the grains of all the major constituent minerals become smaller from Group I (<5 mm) through Group II (<2.5 mm) to Group III (<1.6 mm). In particular, the pyrrhotite contents and their grain sizes show logarithmic correlation with the SIP phase differences, Although we present here the results solely from nine samples, the systematic interrelations especially for pyrrhotite indicate the potential ability of SIP measurements as a new mine-evaluation technique for the sulfide ore reservoir.