• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.10
• /
• pp.97-103
• /
• 2015

This paper presents the characteristics of partial discharge and radiated electromagnetic waves in the existence of a poor contact for the insulation diagnosis of eco-friendly power equipment. AC surface discharge experiment was conducted to simulate the poor contact between a hive voltage electrode (anode) and a solid insulator in $N_2/O_2$ mixture gas under a non-uniform field. The partial discharge voltage to be measured at 0.3MPa increased with the increase of the poor contact gap and was saturated with the gap. In addition to the partial discharge characteristics, it was verified that the defect of the poor contact can be diagnosed using the radiated electromagnetic waves due to the partial discharge, which measured by a biconical EMC antenna and a spectrum analyzer.

• Proceedings of the KIEE Conference
• /
• 1994.11a
• /
• pp.270-273
• /
• 1994

The capacitive current breaking capability as well as the short circuit current breaking capability is a very important factor in the performance of a circuit breaker. The dielectric recovery capability between poles should be considered in the desist of a circuit breaker because approximately two times of the maximum power system voltage might be applied between poles after the capacitive current be interrupted. The electric field and flow field analyses were utilized in the calculation of dielectric recovery characteristics between poles of 800kV model interrupter. The results show that the separation between moving main contact and moving arcing contact will affect to decrease significantly the electric field strength of a moving arcing contact and an insulation cover, to increase slightly the electric field strength of a fixed arcing contact and to decrease consequently the dielectric recovery capability between poles of the interrupter.

• Tribology and Lubricants
• /
• v.35 no.5
• /
• pp.294-299
• /
• 2019

Most previous studies on water repellent surfaces using lasers rely on the use of pico- or femtosecond lasers. However, in industrial application, these methods have the disadvantages of high cost and low efficiency. In this study, we implement a hydrophobic surface using a high-power general-purpose diode laser. We have fabricated the microsurface using laser groove processing technology, and we present the correlation of wettability characteristics with space and width. The metal material is stainless steel (SUS 304), and the groove height during laser processing is set to $30{\mu}m$ to evaluate the wettability based on the gap and width of various grooves. Results show that the contact angle of the groove-shaped surface is increased by $40^{\circ}$ or more as compared with the surface without patterning, and the contact angle in the parallel direction is greater than that in the perpendicular direction. Results from contact angle hysteresis measurement experiments show that the groove width has a greater influence on the contact angle history than does the gap between grooves. In addition, the coating reveals that the contact angle can be increased using a chemical method and that the laser grooving process can further improve the wetting properties of the surface.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.11
• /
• pp.35-40
• /
• 2019

Laser processing has been used in various fields. In this study, the feasibility of a hydrophobic surface was investigated through the laser cladding technique. A diode laser was used, and the output was set to 600-800 W. Seven different specimens were prepared with different cladding widths and spacings, and the contact angles for water droplets were evaluated. As a result, the contact angle of water droplets measured in the direction parallel to the cladding line was higher than that in the vertical direction. The wider the cladding width and the cladding space, the higher the contact angle in the parallel direction. It is thought that when a higher contact angle is formed in the parallel direction, more air can be placed in the valley between the cladding lines. In addition, for the hydrophobic coating effect, the contact angle of the coated cladding surface was increased by about $5-15^{\circ}$ as a whole compared to the coated smooth surface. It was confirmed that the wetting characteristics were improved through the cladding.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.1
• /
• pp.15-23
• /
• 2002

In this study, metal/ZnO contacts were thermally annealed at different temperatures (as-dep., 400$^{\circ}C$, 600$^{\circ}C$, 800$^{\circ}C$, 1000$^{\circ}C$) for the investigation of electrical properties, and surface and interface characteristics. The analysis of the element composition and the chemical bonding state of the surface was made by the XPS(X-ray photoelectron spectroscopy). An attempt was made to establish the electrical property-microstructure relationship for the (Ti, Au)/ZnO. The Ti/ZnO contact exhibits an ohmic characteristics with a relatively high contact resistance of 4.74${\times}$10$\^$-1/ $\Omega$$\textrm{cm}^2$ after an annealing at 400$^{\circ}C$. The contact showed a schottky characteristics when the samples were annealed at higher temperature than 400$^{\circ}C$. The transition from the ohmic to schottky characteristics was contributed from the formation of the oxide layers as was confirmed by the peaks for O-O and Ti-O bondings in XPS analysis. For the Au/ZnO contact the lowest contact resistance was obtained from the as-deposited sample. The resistance was slowly increased with annealing temperature up to 600$^{\circ}C$. The ohmic characteristics were maintained eden fort 600$^{\circ}C$ annealing. The XPS analysis showed that the Au-O intensity was dramatically decreased with temperature above 600$^{\circ}C$.

• Geomechanics and Engineering
• /
• v.10 no.6
• /
• pp.775-791
• /
• 2016

The indirect tensile strengths (ITSs) of different cemented paste backfill mixes with different curing times were determined by considering crack initiation and fracture toughness concepts under different loading conditions of steel loading arcs with various contact angles, flat platens and the standard Brazilian test jaw. Because contact area of the ITS test discs developes rapidly and varies in accordance with the deformability, ITSs of curing materials were not found convenient to determine under the loading apparatus with indefinite contact angle. ITS values increasing with an increase in contact angle can be measured to be excessively high because of the high contact angles resulted from the deformable characteristics of the soft paste backfill materials. As a result of the change of deformation characteristics with the change of curing time, discs have different contact conditions causing an important disadvantage to reflect the strength change due to the curing reactions. In addition to the experimental study, finite element analyses were performed on several types of disc models under various loading conditions. As a result, a comparison between all loading conditions was made to determine the best ITSs of the cemented paste backfill materials. Both experimental and numerical analyses concluded that loading arcs with definite contact angles gives better results than those obtained with the other loading apparatus without a definite contact angle. Loading arcs with the contact angle of $15^{\circ}$ was found the most convenient loading apparatus for the typical cemented paste backfill materials, although it should be used carefully considering the failure cracks for a valid test.

• Proceedings of the KIEE Conference
• /
• 2005.05b
• /
• pp.75-78
• /
• 2005

The decisive criteria to determine collection performance is the contact force between pantograph and catenary. The contact force consists of a static force and dynamic force related to vibration characteristics, train speed and etc. The low contact force leads to the loss of contact, and most countries regulate it below 1% at operation speed. This study presents a technical overview of criteria for collection performance of catenary system.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.05a
• /
• pp.179-184
• /
• 2002

Adhesive contact characteristics of torus-shaped bumps, which are commonly used to reduce friction and stiction in hard disks, are analyzed to examine the applicability to the MEMS structure. The analysis is conducted with the finite element technique considering the adhesive force. Torus-shaped bumps of various rim and bump radii are analyzed. The jump-to-contact behavior, adhesion hysterisis, pull-off forces, contact region and pressure, and surface and subsurface stresses are presented and discussed. Analysis results in the absence of adhesive force are also presented to identify the effect of adhesive force.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.7
• /
• pp.1581-1589
• /
• 1995

The feasibility of using AE for detecting contact and slip between a workpiece and an end effector has been tested. Specifically, the relationship between the contact and slip motion and the characteristics of the AE signal is theoretically and experimentally investigated. The experimental results manifest that the high sensitivity of AE signal to the contact and slip makes it a good alternative as a robot tactile sensor.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.12
• /
• pp.988-991
• /
• 2011

We fabricated a copper phthalocyanine (CuPc) based field-effect transistor with different device structure as a bottom and top contact FET. Also, we used a $SiO_2$ as a gate insulator and analyzed using a current-voltage (I-V) characteristics of the bottom and top contact CuPc FET device. In order to discuss the channel formation, we were observed the capacitance-gate voltage(C-V) characteristics of the bottom and top contact CuPc FET device.