• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.4 s.109
• /
• pp.420-427
• /
• 2006

In this study, wind loads transmitted to a transmission tower from transmission lines are mitigated using rotational viscoelastic dampers. First, the wind load characteristics in a transmission tower is investigated considering the effect of the transmission lines through stochastic analysis. The assemblage of the transmission line and insulator are modeled as a double pendulum system connected to the SDOF model of the tower. From the result of the stochastic analysis, the background component of the overturing moment caused by the wind loads acting on the transmission lines are found to have considerable portion in the total overturning moment. Based on this observation result, a strategy Installing rotational viscoelastic damper (VED) between tower arm and transmission line is proposed for the mitigation of the transmission line reactions, which play a role as dynamic loads on a transmission tower. For the purpose of verification, time history analysis is conducted for different wind velocities and VED parameters. The analysis result shows that the rotational VED is effective for the mitigation of the background component rather than the resonance component of the transmission line reactions and achieves the reduction ratio of 50% even for higher wind speed.

• Nuclear Engineering and Technology
• /
• v.45 no.4
• /
• pp.523-528
• /
• 2013

The beam position monitor (BPM) is an essential component for the PEFP 100-MeV linac's commissioning. A prototype stripline-type linac BPM was designedfor this purpose. The electrode aperture is 20 mm in diameter, and the electrode is 25 mm long, so it can be installed between Drift Tube Linac (DTL)101 and DTL102, which is the shortest distance. One end of the electrode is connected to the Sub Miniature Type A (SMA) feed through for signal measurement, and the other end is terminated as a short. The signal amplitude of the fundamental component was calculated and compared with that of the second harmonic component. The designed BPM was fabricated and a low-power RF test was conducted. In this paper, the design, fabrication and low power test of the BPM for the PEFP linac are presented.

• Progress in Superconductivity and Cryogenics
• /
• v.8 no.4
• /
• pp.22-25
• /
• 2006

This paper deals with the computation of the current limiting behavior of high-temperature superconducting (HTS) modules for the superconducting fault current limiter (SFCL). The SFCL module consists of a monofilar type BSCCO-2212 tube and a shunt coil made of copper or brass. The shunt coil is connected to the monofilar superconducting tube in parallel. Through analysis of the quench behavior of the monofilar component with shunt coils, it is achieved to drive an equivalent circuit equation from the experimental circuit structure. In order to analyze the quench behavior of the SFCL module, we derived a partial differential equation technique. Inductance of the monofilar component and the impedance of the shunt coil are calculated by Bio-Savart and Ohm's formula, respectively. We computed the quench behavior using the calculated values, and compared the results with experimental results for the quench characteristics of a component. The results of computation and test agreed well each other, and it was concluded that the analytic result could be applied effectively to design of the distribution-level SFCL system.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.2
• /
• pp.358-363
• /
• 2009

Text region detection from the natural scene images used in a variety of applications, many research are needed in this field. Recent research methods is to detect the text region using various algorithm which it is combination of edge based and connected component based. Therefore, this paper proposes an text region detection using edge and regional minima/maxima transformation algorithm from natural scene images, and then detect the connected components of edge and regional minima/maxima, labeling edge and regional minima/maxima connected components. Analysis the labeled regions and then detect a text candidate regions, each of detected text candidates combined and create a single text candidate image, Final text region validated by comparing the similarity and adjacency of individual characters, and then as the final text regions are detected. As the results of experiments, proposed algorithm improved the correctness of text regions detection using combined edge and regional minima/maxima connected components detection methods.

• Journal of Power Electronics
• /
• v.11 no.3
• /
• pp.360-368
• /
• 2011

This paper proposes an active frequency with a positive feedback in the d-q frame anti-islanding method suitable for a robust phase-locked loop (PLL) algorithm using the FFT concept. In general, PLL algorithms for grid-connected PV PCS use d-q transformation and controllers to make zero an imaginary part of the transformed voltage vector. In a real grid system, the grid voltage is not ideal. It may be unbalanced, noisy and have many harmonics. For these reasons, the d-q transformed components do not have a pure DC component. The controller tuning of a PLL algorithm is difficult. The proposed PLL algorithm using the FFT concept can use the strong noise cancelation characteristics of a FFT algorithm without a PI controller. Therefore, the proposed PLL algorithm has no gain-tuning of a PI controller, and it is hardly influenced by voltage drops, phase step changes and harmonics. Islanding prediction is a necessary feature of inverter-based photovoltaic (PV) systems in order to meet the stringent standard requirements for interconnection with an electrical grid. Both passive and active anti-islanding methods exist. Typically, active methods modify a given parameter, which also affects the shape and quality of the grid injected current. In this paper, the active anti-islanding algorithm for a grid-connected PV PCS uses positive feedback control in the d-q frame. The proposed PLL and anti-islanding algorithm are implemented for a 250kW PV PCS. This system has four DC/DC converters each with a 25kW power rating. This is only one-third of the total system power. The experimental results show that the proposed PLL, anti-islanding method and topology demonstrate good performance in a 250kW PV PCS.

• Journal of Sensor Science and Technology
• /
• v.25 no.5
• /
• pp.371-376
• /
• 2016

A self-powered piezoelectric energy harvester was developed for the application in wireless sensor node. The energy harvester was evaluated with power generation characteristics for the wireless sensor node for structural diagnosis of the electric power system. The self-powered wireless sensor node was set to measure temperature, vibration frequency of the electric power system. A piezoelectric harvester composed of 7 uni-morph cantilevers (functionalized as 6 generators and 1 vibration sensor) was connected to be an array and revealed to produce significantly high output power of approximately 10 mW at 120 Hz under 3.4 g((1 g = $9.8m/sec^2$). The wireless sensor node could work as the electric power generated by the developed piezoelectric harvester.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.12
• /
• pp.769-775
• /
• 2016

Characteristics of a wireless sensor powered by the IDE (interdigitated electrode) embedded piezoelectric cantilever generator were analyzed in order to evaluate its potential for use in wireless sensor applications. The IDE embedded piezoelectric cantilever was designed and fabricated to have a self-resonance frequency of 126 Hz and acceleration of 1.57 G, respectively, for the mechanical resonance with a practical conveyor system in a thermal-power plant. It produced maximum output power of 2.81 mW under the resistive load of $160{\Omega}$ at 126 Hz. The wireless sensor module is electrically connected to a rectifier capacitor with capacity of 0.68 farad and 3.8 V for power supply by the piezoelectric cantilever generator. The unloaded capacitor could be charged as a rate of approximately $365{\mu}V/s$ while the capacitor exhibited that of 0.997 mV/min. during communication under low duty cycle of 0.2%. Therefore, it is considered that the fabricated IDE embedded piezoelectric cantilever generator can be used for wireless sensor applications.

• Journal of Veterinary Clinics
• /
• v.33 no.5
• /
• pp.278-285
• /
• 2016

Epidemiological studies have shown the association between transportation of live animals and the potential transmission of infectious disease between premises. This finding was also observed in the 2014-2015 foot-and-mouth disease (FMD) outbreak in Korea. Furthermore, slaughterhouses played a key role in the global spread of the FMD virus during the epidemic. In this context, in-depth knowledge of the structure of direct and indirect contact between slaughterhouses is paramount for understanding the dynamics of FMD transmission. But the social network structure of vehicle movements to slaughterhouses in Korea remains unclear. Hence, the aim of this study was to configure a social network topology of vehicle movements between slaughterhouses for a better understanding of how they are potentially connected, and to explore whether FMD outbreaks can be explained by the network properties constructed in the study. We created five monthly directed networks based on the frequency and chronology of on- and off-slaughterhouse vehicle movements. For the monthly network, a node represented a slaughterhouse, and an edge (or link) denoted vehicle movement between two slaughterhouses. Movement data were retrieved from the national Korean Animal Health Integrated System (KAHIS) database, which tracks the routes of individual vehicle movements using a global positioning system (GPS). Electronic registration of livestock movements has been a mandatory requirement since 2013 to ensure traceability of such movements. For each of the five studied networks, the network structures were characterized by small-world properties, with a short mean distance, a high clustering coefficient, and a short diameter. In addition, a strongly connected component was observed in each of the created networks, and this giant component included 94.4% to 100% of all network nodes. The characteristic hub-and-spoke type of structure was not identified. Such a structural vulnerability in the network suggests that once an infectious disease (such as FMD) is introduced in a random slaughterhouse within the cohesive component, it can spread to every other slaughterhouse in the component. From an epidemiological perspective, for disease management, empirically derived small-world networks could inform decision-makers on the higher potential for a large FMD epidemic within the livestock industry, and could provide insights into the rapid-transmission dynamics of the disease across long distances, despite a standstill of animal movements during the epidemic, given a single incursion of infection in any slaughterhouse in the country.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.2
• /
• pp.872-877
• /
• 2012

We proposes the method to detect the Hangul character region from natural image using topological structural feature of Hangul grapheme. First, we transform a natural image to a gray-scale image. Second, feature extraction performed with edge and connected component based method, Edge-based method use a Canny-edge detector and connected component based method applied the local range filtering. Next, if features are not corresponding to the heuristic rule of Hangul character, extracted features filtered out and select candidates of character region. Next, candidates of Hangul character region are merged into one Hangul character using Hangul character merging algorithm. Finally, we detect the final character region by Hangul character class decision algorithm. Experimental result, proposed method could detect a character region effectively in images that contains a complex background and various environments. As a result of the performance evaluation, A proposed method showed advanced results about detection of Hangul character region from mobile image.

• Proceedings of the Korea Technology Innovation Society Conference
• /
• 2003.05a
• /
• pp.413-425
• /
• 2003

Information Technology is the kernel technology deciding the industrial standard of one nation, and biotechnology will be the main technology of next generation. Based on this fact, a lot of efforts were made to industrialize them. Nano Technology is beginning to position itself as the kernel fusion technology, and its usage and popularity is expanding. Environmental and Energy Technology is a must-have strategic technology considering the increase demand of new energy development, the international environment correspondence, the environment-friendly production, and so forth. Space Technology is the field, which will contribute to raise the domestic component and system technology to the next level. In 2001, new technology research development costs total of 1 trillion 32 billion won in the following fields; 437.82 billion won in IT, 88.457 billion won in BT, 46.799 billion won in NT, 315.682 billion won in ET, and 112 billion won in ST. from component ratio, IT forms 42% which is the most, 31% for ET and in order of BT, ST and NT. ETRI and KISTI are concentrating on IT, KIBB is on BT, KAERI, KIER, KERI and KBSI are focusing on ET, and KIMM, KRISS, KRICT and KORDI is participating together in 4∼5 new technology such as IT, BT, NT and ET. Funds for research development costs in 5 new technology fields of 13 contribution (year) are consisted as follows; The Office for Government Policy Coordination has contributed 131 billion won (13%), 387 billion won (37%) by MOST, 256 billion won (25%) by Ministry of Information and Communication, 67 billion won (6%) by Ministry of Commerce, Industry and Energy, 19% by others and the industrial world. < Strategy for Technology Advancing > o Promotion of comprehensive contributing (year) new technology development research plan project o Increase research efficiency by promoting new technology development project connected with peculiar projects of organization by contribution (year) o Formation of superior research group by technology and introduction of operation system for research accumulation are needed. o Technology demand-oriented assignment deduction and promotion of research development project connected with intermediate long term objective o National will and investment extension of research development costs, training and popularization of professionals, commercialization promotion with efficient control for research plan and result.