• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.328-329
• /
• 2020

The AC/DC converter, which connects the AC grid to the DC grid in the microgrid, is a critical component in power sharing and stable operation. Sometimes the AC/DC converters are connected in parallel to increase the transmission and reception capacity. When connected in parallel, circulating current is generated due to line impedance difference or sensor error. As a result of circulating current, there is deterioration and loss in particular PCS(Power Conversion System). In this paper, we propose droop control with novel adaptive virtual impedance for reducing circulating current. Feasibility of proposed algorithm is verified by PowerSIM simulation.

• Journal of the Microelectronics and Packaging Society
• /
• v.7 no.1
• /
• pp.1-5
• /
• 2000

Co-fired resistors for high frequency MCM-C (Multi Chip Module-Cofired) were fabricated and measured their RF properties from DC to 6 GHz. LTCC (Low Temperature Co-fired Ceramics) substrates with 8 layers were used as the substrates. Resisters and electrodes were printed on the 7th layer and connected to the top layer by via holes. Deviation from DC resistance of the resistors was resulted from the resister pastes, resistor size, and via length. From the experimental results, the suitable equivalent circuit model was adopted with resistor, transmission line, capacitor, and inductor. The characteristic impedance $Z_{o}$ of the transmission line from the equivalent circuit can explain the RF behavior of the buried resistor according to the structural variation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.5
• /
• pp.2567-2572
• /
• 2014

In the present study, we aimed to obtain multi jig that PCB sheet with several PCB component can cut in a short time as to the Separation of PCB component. PCB supporter designed safely at the base frame and each model can be separable. it completed the neodium magnet for the fixing of the upper part laser transmission hole of the both. One of the development, the cutting working with one base frame which PCB component of various standard, fixing of module and bridge connected to PCB component could be possible. and it reduced the inconvenience which has to replace the base frame and PCB sheet fixed member. It compared to other press up about 70% of accuracy and a reduction in investment cost was about 400%.

• Journal of Korea Multimedia Society
• /
• v.10 no.5
• /
• pp.594-603
• /
• 2007

This paper proposes a watermarking scheme for 3D CAD design drawing. In the proposed scheme, we embed binary watermarks into line, arc, and polygon face components that are the basic component of 3D CAD design drawing. The embedding target component can be selected randomly among three components or by the component distribution in drawing. In line components, a watermark bit is embedded into the ratio of the length of a target line and an average length of lines that are connected into a target line. Furthermore, a watermark bit is embedded into a curvature radius on the basis of a center point in a arc component and also is embedded into a ratio of two sides in a polygonal face component. Experimental results verified that the proposed watermarking has the robustness against Format conversion, rotation translation, scaling, cropping, and layer cutting and also SNR of watermarked component is about 39.89-42.50 dB.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.1
• /
• pp.58-64
• /
• 2008

In this paper, we present an active anti-islanding method with a load monitoring system using reactive power control. The proposed method, which is based on reactive power control, has fewer harmonics components than those in conventional methods, and it can minimize the reactive power component of the grid because it compensates the reactive power component with the load monitoring. The proposed quick islanding detection method was confirmed from the experimental results with an inverter for a 3kW photovoltaic system.

• KSBB Journal
• /
• v.26 no.1
• /
• pp.87-91
• /
• 2011

Automatic counting of yeast cells in baker's yeast culture was tried using a conventional light microscope equipped with a pc camera. Relatively good binary image was obtained by using white LED as microscope light source, but uneven brightness distribution in original image hindered counting accuracy. A block binarization method using local thresholds proportional to local brightnesses was used to get improved binary images. The brightnesses of the blocks were expressed as the value component in HSV color model. Good quality binary images were obtained by binarization on $8{\times}6$ blocks of original images and connected-component labelling of the binarized images produced reliable counting results in the concentration range $1.4{\times}10^5/mL{\sim}1.4{\times}10^7\;cells/mL$.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.5
• /
• pp.258-264
• /
• 2006

This paper presents an integrative control scheme for series-type active power filters combined with shunt passive filters not only to compensate for the source voltage unbalance and current harmonics but also to correct the power factor. To reduce the power capacity of the active filters, passive filters are connected in parallel. Diode rectifiers are replaced by the PWM converters in order to feed the real power back to the source. Power factor control is performed by changing the phase of the load voltage so that the phase of the source current coincides with that of the source voltage. The resultant voltage reference is the addition of the voltage component compensating for the source voltage unbalance and harmonic currents and the voltage component correcting the power factor. The validity of the proposed algorithm has been verified by experimental results.

• Journal of the Korean Solar Energy Society
• /
• v.30 no.1
• /
• pp.7-12
• /
• 2010

As many grid-connected photovoltaic power conditioning systems (PVPCS)are installed in many residential areas simultaneously, these have raised potential problems of network protection on electrical power system. One of the numerous problems is an Islanding phenomenon. In this paper, active frequency drift (AFD) method, one of the anti-islanding methods which is analyzed by current magnitude compensation and calculation of the fundamental component. Both harmonic component and RMS value of the output current for THD analysis are provided and verified by simulation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.7 s.238
• /
• pp.1013-1021
• /
• 2005

In this paper, we developed an automatic design optimization system for parametric shape optimization of cooling passages inside axial turbine blades. A parallel three-dimensional thermoelasticity finite element analysis code from an open source system was used to perform automatic thermal and stress analysis of different blade configuration. The developed code was connected to an evolutionary optimizer and built in a design optimization system. Using the optimization system, 279 feasible and optimal solutions were searched. It is provided not only one best solution of the searched solutions, but also information of variation structure and correlation of the 279 solutions in function, variable, and real design spaces. To explore design information, it is proposed a new interpretation approach based on evolutionary clustering and principal component analysis. The interpretation approach might be applicable to the increasing demands in the general area of design optimization.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.5 no.6
• /
• pp.544-551
• /
• 2000

In this paper, 3-phase hybrid series active power filter for compensate current harmonics, voltage drop and unbalanced voltage in the network presented. The proposed system is implemented with a space vector modulation voltage source inverter and a high pass filter connected in parallel to the power system. Here the load is six-pulses thyristor rectifier. The phase angle detected in order to generation reference voltage at load terminal is synchronized with the positive sequence component of the unbalanced source by using symmetrical component transformation. The proposed system has an function harmonic isolation between source and load, voltage regulation, and unbalance compensation. Therefore, what the power system is improved quality, the source current is maintained as a nearly sinusoidal waveform and the load voltage is regulated with a rated voltage regardless of the source variation condition. To verify the validity of the proposed compensating system, the computer simulation and experiment are carried out.