• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1989년도 추계 학술발표회 강연집
• /
• pp.1.2-17
• /
• 1989

花崗巖 Beam 試料에 대하여 4-Point Bending 試驗이 진행되는 동안 試料 破壤에 隋伴된 AE 信號를 Calibrated PZT Transducer와 6-Channel Recording System으로 기록하여 分析함으로서 微細 龜裂源의 特性과 機構를 糾明하였다. 微細 龜裂의 體積은 수 um3에서 150.000um3의 넓은 범위를 보였으며, 引張形 龜裂이 斷形에 비하여 大體的으로 큰 것으로 밝혀 졌다. 龜裂源에서의 强度는 Mode I 荷重 下에서 기록된 것이 Mixed Mode 試驗에서 얻어진 것보다 그 平均値가 약 3배 정도 크게 나타났으나, 전체 AE 數에 있어어는 反對로 Mixed Mode 試驗에서 기록된 것의 약 25% 밖에 되지 않아서 같은 크기의 破壤面을 形成하는데 必要한 에너지 要求量이 일정함을 暗示하였다. 미세 龜裂面의 方位는 垂直 및 水平에 近接한 傾斜를 가지며 走向은 최종 試料의 破壤面과 일치할 뿐만 아니라 龜裂源이 시료 破壤面에 집중되게 分布하여서 微細 龜裂이 試料龜裂을 야기시키는 原因임을 알 수 있었다. 또한, Mode I 荷重 下에서는 引張形의 微細龜裂이 압도적으로 優勢하였고, Mixed Mode 荷重 下에서는 引張과 斷形의 微細龜裂이 약 3,6:1 比率로 分布하여서 荷重 條件이 微細 龜裂의 機構와 密接한 關係가 있음을 알 수 있었다.

• 한국주거학회:학술대회논문집
• /
• 한국주거학회 2003년도 정기총회 및 추계학술대회
• /
• pp.47-51
• /
• 2003

In this paper, we compared the thermal environment in the livingroom with panel heating system of Korea and Japan. The houses are two apartments and two single houses in Korea, and two apartments in Japan. The outdoor temperatures, indoor air temperatures, surface temperatures on floor and humidities were measured. The survey to the residents and recording of operation were also collected. The results were as follows.1. The Korean houses are warmer and drier(approximately 23$^{\circ}$C, 38%) than those of Japan.(approximately 20$^{\circ}$C, 57%). And indoor temperaures of Korean apartment are stabie. 2.The residents in Japan put on and off the switches of the heating system frequently.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1992년도 추계학술대회 논문집
• /
• pp.7-10
• /
• 1992

CoNiCr/Cr and CoCrTa/Cr for longitudinal magnetic recording media were. prepared on Coming 7059 glass by RF magnetron sputtering. The thickness of Cr underlayer was varied from 500 to $3000{\AA}$ and. that of magnetic layer was $700{\AA}$. Coercivity and squareness were measured using V.S.M.(vibrating sample magnetometer). The coercivity of films increased with increasing Cr thickness when the films were unannealed. The coercivity of the films annealed in a 10 mtorr vacuum increased initially with annealing time and then saturated with further increase in annealing time. The coercivity value difference between the unannealed and annealed films increased with increasing the thickness of Cr underlayer No significant change was found in squareness after anneal, regardless of Cr underlayer thickness.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.2110-2111
• /
• 2008

Continuous on-line temperature monitoring allows corrective measures to be taken to prevent upcoming failure. Continuous temperature monitoring and event recording provides information on the energized equipment's response to normal and emergency conditions. On-line temperature monitoring helps to coordinate equipment specifications and ratings, determine the real limits of the monitored equipment and optimize facility operations. Using wireless technique eliminates any need for special cables and wires with lower installation costs if compared to other types of online condition monitoring equipment. In addition, wireless temperature monitoring works well under difficult conditions in strategically important locations. Wireless technology for on-line condition monitoring of energized equipment is applicable both as standalone system and with an interface with power quality monitoring system.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.475-480
• /
• 2000

A new positioning mechanism with Parallel type actuator using piezoelectric material and with dual type actuators using voice coil motor (VCM) and piezoactuator is proposed for optical disk drive or near-field recording type drive, and high speed position and vibration control are investigated. Parallel type bimorph piezoactuator is used as a fine motion actuator with self-sensing technique, which allows a piezoelectric material to concurrently sense and actuate in a closed loop frame work, and positive position feedback control algorithm is adopted to further control residual vibration. For positioning control of VCM, PID control algorithm is adopted.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.290-295
• /
• 2000

An experimental study was carried out in a cavity with upper channel and square heat surface by visualization equipment with Mach-Zehnder interferometer and laser apparatus. The visualization system consists of 2-dimensional sheet light by Argon-Ion Laser with cylindrical lens and flow picture recording system. Instant simultaneous velocity vectors at whole field were measured by 2-D PIV system(CACTUS'2000). Obtained result showed various flow patterns. Severe unsteady flow fluctuation within the cavity are remarkable and sheared mixing layer phenomena are also found at the region where inlet flow is collided with the counter-clockwise rotating main primary vortex. Photographs of Mach-Zehnder are also compared in terms of constant heat flux.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.670-675
• /
• 2003

With the increase in recording density and higher rotation speeds, the aerodynamic aspect of hard disk drives (HDDs) is now quite significant. To achieve high TPI (tracks per inch) for hard disk drives, the actuator must induce less air turbulence. Also, alternative cross sections for the actuator arms are proposed for the reduction of air turbulence. In this study, off-track vibration of actuator arms used in of 3.5" hard disk drives with different cross sections have been measured by using Laser Doppler Vibrometer (LDV). It has been found that the vibration of the actuator arms with modified cross sections is lower than the conventional one.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.676-681
• /
• 2003

In this paper, we investigated the disc warping in high-speed slim-type optical disc drive. Recently, the information storage devices are increasing track density and higher rotation speed to enhance their recording capacity and their data transfer rate. Generally, ODD used in the Lap-top Computer has small inner space. So, the flow instability of inner space is rapidly increased as its higher rotation speed. An extreme case, the flow instability causes the malfunction of readout at pick-up of drives. The experiments and numerical analysis were carried out for several cases, the result shows the influence of airflow to the disc warping.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2017년도 춘계 학술논문 발표대회
• /
• pp.260-261
• /
• 2017

The objective of this study is to propose the basic design plan of system by comparing and analyzing application environment of lift and elevator group control system, as preliminary study for the application of group control system to lifts for high-rise construction. The basic design plan is suggested in terms of group control algorithm, hall call system type, operation information recording device, information communication method, and operation method. The results of this study can be used as basic data for software and hardware design for application of group control technology of lifts for super tall building construction and ultimately contribute to improve the operation efficiency of lift for high-rise construction.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 춘계학술대회 논문집
• /
• pp.15-18
• /
• 1996

The elemental segregation in the sputter-deposited AgInSbTe recording thin films was studied by means of Auger electron spectroscopy and ESCA for the specimens of as-deposited and as heat-treated conditions. Auger electron spectroscopy and ESCA revealed an extremely thin layer of elemental inhomogeneity, especially for the silver, even in as-deposited condition. The chemical analysis results obtained in this alloy system are discussed in terms of process parameters and target microstructure.