• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2002년도 추계학술발표회
• /
• pp.366-369
• /
• 2002

Subsurface biobarrier technology has potential applications to contain contaminated groundwater and/or to degrade toxic pollutants in groundwater. Most biobarrier studies were conducted under aerobic condition, however there were several obstacles to make aerobic condition. Thus, In this study, we examined biobarrier formation under denitrifying condition by using nitrate as an electron acceptor. Experiments were performed with a sand column inoculated with activated sludge from the nearby WWTP. The substrate medium was pumped to the sand column in an upflow mode. During the low substrate loading rate period, the extent of reduction rate in hydraulic conductivity was found similar throughout the column, and permeability became relatively stable after couple of days. However, during the high substrate loading rate period, the column demonstrated a gradient of permeability reduction, with the greatest reduction in sections nearest the column inlet. Rapid growth of microorganisms near the column inlet resulted in the unbalanced reduction of hydraulic conductivity throughout the sand column. As a result, at this denitrifying condition the thickness of biobarrier could be controlled by adjusting the medium conditions of microbial growth.

• 한국분말재료학회지
• /
• 제11권2호
• /
• pp.158-164
• /
• 2004

W-Cu composite has been used for the applications requiring both high strength, good thermal and electrical conductivity. A graded combination of W and Cu will reduce thermal stress concerned with heat conduction, maintaining good thermal conductivity and high mechanical strength. In the present work, an attempt was made to fabricate continuous W-Cu FGM by preparing the graded porous structure of W skeleton using spark plasma sintering (SPS) process followed by infiltrating Cu. The graded porous structure was prepared at 150$0^{\circ}C$ for 60s under pressure of 15MPa by SPS process using a graphite mold with varying crr)ss section in the longitudinal direction. Infiltration of Cu was performed at 115$0^{\circ}C$ for 1 hour under $H_2$. W-Cu composite with graded Cu composition of 14 to 27 wt％ was finally prepared. In this process the gradient of composition could be conveniently controlled by varying the gradient of cross sectional area of graphite mold, temperature and pressure.

• 지질공학
• /
• 제17권4호
• /
• pp.643-653
• /
• 2007

수락산 터널지역 내 8개 시추공에서 조사된 기반암의 평균 수리전도도 $2.64{\times}10^{-8}m/sec$, 평균 RQD 78%, 평균공극율 0.51% 및 지하수위는 $77.06{\sim}125.97m$의 범위이었다. 지하수위와 표고간의 회귀분석 결과를 이용하여 수락산 터널 지역 내 두 개의 정상부에서 지하수위를 추정하여 구한 터널 구간의 평균적인 수평수리경사는 0.267 이었다. 수락산 터널 구간에서 현장투수시험에 의해 구해진 최소 수리전도도는 $5.56{\times}10^{-9}m/sec$, 최대 수리전도도는 $6.12{\times}10^{-8}m/sec$, 평균 수리전도도는 $2.64{\times}10^{-8}m/sec$ 이었다. 최소, 최대 및 평균 수리전도도와 평균적인 수평수리경사를 이용하여 산정된 수락산 터널 구간 내에서의 단위 길이 당 지하수 유출량은 각각 $0.00585m^2/day,\;0.06434m^2/day$ 및 $0.02775m^2/day$ 이었다. 물수지분석에 의한 연구지역 내 단위함양유역 당 순수지하수함양율은 224mm/yr로 산정되었다. 터널굴착이 완료된 후 최소, 최대 및 평균 수리전도도를 적용한 지하수위 변동예측 모사에 의하면 수리전도도가 낮을수록 터널 내로의 유출량은 적었지만, 지하수위 강하량은 크게 나타났다. 그리고, 최대 수리전도도를 적용한 모사 시에는 터널로의 유출량이 크지만, 대수층으로의 충진이 빠르게 발생하여 지하수위가 짧은 시간에 회복되었다.

• 지질공학
• /
• 제27권4호
• /
• pp.377-382
• /
• 2017

안성천 수계 하류부 국가하천구간내 15개 지점에 대해 하상퇴적층의 수리전도도 측정 시험을 수행하였다. 각 지점별로 하상퇴적층에 시피지미터와 피조미터를 설치하여 하천수-지하수 상호교환량과 수리경사를 측정하고 이를 Darcy 공식에 대입하여 연직방향 수리전도도를 산정하였다. 하천수-지하수 교환량은 $4.08{\times}10^{-6}{\sim}1.49{\times}10^{-5}m/s$, 연직방향 수리경사는 0.005에서 0.145로 측정되었고, 하상수리전도도는 $7.80{\times}10^{-5}{\sim}1.58{\times}10^{-3}m/s$로 산정되어 하천구간별, 지점별로 하천과 대수층간에 연결성의 큰 차이를 나타내었다. 하천과 대수층간의 수리적 상호연결성을 정량적으로 파악하고 지하수개발 이용이 하천수량에 미치는 영향을 평가하기 위해서는 하상퇴적층 수리전도도와 같이 하천과 대수층간 연결부의 수리지질학적 조사가 필요하며, 현장시험 및 분석 방법에 대한 기술적 향상이 이뤄져야 할 것이다.

• International Journal of Concrete Structures and Materials
• /
• 제10권1호
• /
• pp.39-46
• /
• 2016

In this study, different proportions of glass beads used for road marking were added into the concrete samples to reduce the temperature gradient through the concrete pavement thickness. It is well known that decreasing the temperature gradient reduces the risk of thermal cracking and increases the service life of concrete pavement. The extent of alkali-silica reaction (ASR) produced with partial replacement of fine aggregate by glass bead was investigated and compressive strength of concrete samples with different proportion of glass bead in their mix designs were measured in this study. Ideal results were obtained with less than 0.850 mm diameter size glass beads were used (19 % by total weight of aggregate) for C30/37 class concrete. Top and bottom surface temperatures of two different C30/37 strength class concrete slabs with and without glass beads were measured. It was identified that, using glass bead in concrete mix design, reduces the temperature differences between top and bottom surfaces of concrete pavement. The study presented herein provides important results on the necessity of regulating concrete road mix design specifications according to regions and climates to reduce the temperature gradient values which are very important in concrete road design.

• 한국레이저가공학회지
• /
• 제3권1호
• /
• pp.29-37
• /
• 2000

For a development purpose of thick metal / metal Graded-Boundary Materials(GBM), a basic research on the fabrication of Ni-Cr/steel GBM was carried out by a laser beam and its mechanical properties and thermal characteristics were investigated. In order to produce a compositionally graded boundary region between substrate steel and added Ni-Cr alloy, a series of surface alloying treatments was performed with a high power CO$_2$ laser beam. Ni-Cr sheet was placed on a low carbon steel plate(0.18%C), and then a CO$_2$ laser beam was irradiated on the surface to produce a homogeneous alloyed layer. On this first surface-alloyed layer, another Ni-Cr sheet was placed and then the CO$_2$ laser beam was irradiated again to produce second surface-alloyed layer. Sequential repetitions of laser surface alloying treatment 4 times resulted in a graded-boundary region with the thickness of about 1.4mm. Simultaneous concentration profiles of different kinds of alloying elements(Ni and Cr) showed from 42%Ni, 45%Cr and 13%Fe on surface region to 0%Ni, 0%Cr and 99%Fe in substrate region. Also a thermal conductivity gradient resulted in graded-region and its value changed from 0.03㎈/cm s$\^{C}$ in surface region to 0.1㎈/cm s$\^{C}$ in substrate region. Microstructural observation showed that any visible root porosities and solidification shrinkage cracks were not formed in graded region between alloyed layer and substrate region during rapid cooling.

• 설비공학논문집
• /
• 제11권2호
• /
• pp.185-192
• /
• 1999

Effective thermal conductivities and pressure-drop-related properties of aluminum foam metals have been measured. The effects of porosity and cell size in the aluminum foam metal are investigated in detail. The porosity of the foam metal, considered in the present study, varies from 0.89 to 0.96 and the cell size from 0.65㎜ to 2.5㎜. The effective thermal conductivity is evaluated by comparing the temperature gradient of the foam metal with that of the thermal conductivity-known material. The pressure drop in the foam metal is measured by a highly precise electric manometer while air is flowing through the aluminum foam metal in the channel. The results obtained indicate that the effective thermal conductivities are found to be increased with a decrease in the porosity while the effective thermal conductivities ire little affected by the cell size at a fixed porosity. However, the pressure drop is strongly affected by the cell size as well as the porosity. It is seen that the pressure drop is increased as the cell size becomes smaller, as expected. The minimum pressure drop is obtained in the porosity 0.94 at a fixed cell size. A new correlation of the pressure drop is proposed based on the permeability and Ergun's coefficient for the aluminum foam metal.

• 한국구조물진단유지관리공학회 논문집
• /
• 제7권3호
• /
• pp.175-181
• /
• 2003

본 논문에서는 상향 침투시험기를 이용하여 3가지 시료에 대하여 상향 투수시험을 수행하였고, 이를 통하여 한계속도, 한계동수경사, 투수계수 등을 산정하여 기존의 세굴 검토 방법에 대한 신뢰성을 파악하였다. 또한 세굴 설계인자에 대하여 FEM Program인 Plaxis를 이용하여 민감도 분석을 수행하였다. 민감도 분석결과 제방 하부의 출구부 동수 경사에 가장 영향을 많이 미치는 인자는 중심코어의 높이로 나타났다. 또한 제방의 구배와 뚝마루 폭이 중심코어의 높이 다음으로 세굴에 영향성이 큰 것으로 나타났다. 그러나 중심코어의 뚝마루폭은 출구부의 동수경사 변화에 영향이 적은 것으로 나타났다. 이러한 민감도 분석결과를 이용하여 설계시 동수경사가 기준 동수경사보다 크게 나타날 경우 민감도 변화가 큰 설계인자를 변경하여 경제적이고 보다 손쉬운 출구부 동수경사 저감이 가능하리라 판단된다.

• 지질공학
• /
• 제21권2호
• /
• pp.157-162
• /
• 2011

지금까지 열전도계수는 불포화토를 대상으로 측정하였으며 측정결과를 토대로 예측 모델의 신뢰성을 연구해 왔다. 그러나 측정 장치의 발열로 인해 불포화토에서는 함수비 구배가 발생하여 열전도계수 측정에 오차가 발생한다. 본 연구에서는 포화된 점성토의 압밀에 따른 열전도계수를 연속적으로 측정하여 건조밀도와 함수비의 변화에 따른 열전도계수의 관계를 연구하였다. 열전도계수는 니들브로브로 측정하였으며 시료의 교란을 최소화하기 위해 니들브로브를 삽입한 상태에서 압밀실험을 진행하였다. 측정결과는 열전도계수 예측 모델을 이용한 결과와 비교를 통해 예측 모델의 신뢰성을 분석하였다.

• 터널과지하공간
• /
• 제8권2호
• /
• pp.79-86
• /
• 1998

This study was performed to suggest to suggest suitable design conditions of water curtain system through analysis on pressure down in boreholes by hydraulic tests carried out I construction fields for underground oil storages. The influence by hydraulic conductivities of rock mass around boreholes on pressure down in boreholes was analysed. The relationship between array of boreholes and their pressure down was also analysed. Groundwater flow analysis on crude oil and LPG storages was carried out to evaluate results of field tests and to investigate distribution of hydraulic gradient in rock mass around cavern using finite difference method. As the results, hydraulic tests showed that pressure down in boreholes was inverse proportional to the hydraulic conductivity of surrounding rock mass. The rate of pressure down of boreholes was not influenced by water curtain system more than 20m over cavern and was proportional to installation interval of boreholes. The hydraulic gradient in rock mass around cavern was proportional to distance and interval of boreholes and its value was not satisfactory to oil tightness condition in case of no water curtain system.