• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.3
• /
• pp.79-86
• /
• 1992

The cause of excess current noise which appears some times in RuO$_2$ thick film chip resistors and the process to reduce such noise are investigated. We observed that too large thermal expansion coefficients of resistor paste and electrode metal paste can induce the mechanical stress and microcracks in the contact region of the two sintered materials. Such microcracks result in the reduction of conduction paths in the sintered electrode and this provokes the increase of the resistance value and the current noise. Such excessive current noise induced by microcracks could be reduced or even eliminated by using an enlarged overcoat patterns in the plating process or by adding an additional annealing process before plating.

• Journal of Digital Convergence
• /
• v.14 no.4
• /
• pp.363-370
• /
• 2016

Noise is unwanted sound that is the reason of the stress and hearing loss. The current study attempted to estimate whether the noise of dental laboratory affected stress and pure tone audiometry (PTA) of dental laboratory technicians (DLTs) using heart rate variability, air and bone conduction audiometry. The age, heights, and weights of DLTs were resembled control. Standard deviation of normal to normal interval such as stress resistance and normalized HF of DLTs were significantly decreased, but heart rates, normalized LF, and LF/HF ratio of DLTs were significantly increased compared with control. In air conduction audiometry of DLTs, significant increments of thresholds encountered in 125, 250, 500, 1000, 2000, 3000, 4000, and 6000 Hz in the right ears and 125, 250, 500, 1000, and 2000 Hz in the left ears. Thresholds of bone conduction audiometry in both ears were significantly increased in 250, 500, 1000, 2000, and 4000 Hz. The findings in this study provide that stress and hearing loss observed in noise-exposed DLTs at dental laboratory. Therefore, proper safety precautions should be carried out at dental laboratory.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2005.12a
• /
• pp.224-225
• /
• 2005

• Proceedings of the Korean Magnestics Society Conference
• /
• 2005.06a
• /
• pp.132-133
• /
• 2005

• Proceedings of the Korean Magnestics Society Conference
• /
• 2008.12a
• /
• pp.253.1-253.1
• /
• 2008

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.556-563
• /
• 2003

This paper presents a method to investigate the characteristics of a hydrodynamic bearing of a HDD spindle motor due to elevated temperature considering the variation of the clearance as well as the lubricant viscosity. Iterative finite element analysis of the heat conduction and the thermal deformation is performed to determine the viscosity and clearance of a hydrodynamic bearing due to elevated temperature until the temperature of the bearing area converges. Proposed method is verified by comparing the calculated temperature with the measured one in elevated surrounding temperature as well as in room temperature. This research shows that elevated temperature changes the clearance as well as the lubricant viscosity of the hydrodynamic bearing of a HDD spindle motor. Once the viscosity and clearance of a hydrodynamic bearing of a HDD spindle motor are determined, finite element analysis of the Reynolds equation is performed to investigate the static and dynamic characteristics of a hydrodynamic bearing of a HDD spindle motor due to elevated temperature. It also shows that the variation of clearance due to elevated temperature is another important design consideration to affect the static and dynamic characteristics of a hydrodynamic bearing of a HDD spindle motor.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.5
• /
• pp.299-304
• /
• 2018

An ideal circuit breaker should supply electric power to loads without losses in a conduction state and completely isolate the load from the power source by providing insulation strength in a break state. Fault current is relatively easy to break in an Alternating Current (AC) circuit breaker because the AC current becomes zero at every half cycle. However, fault current in DC circuit breaker (DCCB) should be reduced by generating a high arc voltage at the breaker contact point. Large fire may occur if the DCCB does not take sufficient arc voltage and allows the continuous flow of the arc fault current with high temperature. A semiconductor circuit breaker with a power electronic device has many advantages. These advantages include quick breaking time, lack of arc generation, and lower noise than mechanical circuit breakers. However, a large load capacity cannot be applied because of large conduction loss. An extinguishing technology of DCCB with polymeric positive temperature coefficient (PPTC) device is proposed and evaluated through experiments in this study to take advantage of low conduction loss of mechanical circuit breaker and arcless breaking characteristic of semiconductor devices.

• Proceedings of the KIEE Conference
• /
• 2006.10b
• /
• pp.154-158
• /
• 2006

The switching-mode power converter has been widely used because of its features of high efficiency and small weight and size. These features are brought by the ON-OFF operation of semiconductor switching devices. However, this switching operation causes the surge and EMI(Electromagnetic Interference) which deteriorate the reliability of the converter themselves and entire electronic systems. This problem on the surge and noise is one of the most serious difficulties in AC-to-DC converter. Random Pulse Width Modulation (RPWM) is peformed by adding a random perturbation to switching instant while output-voltage regulation of converter is performed. RPWM method for reducing conducted EMI in single switch three phase discontinuous conduction mode boost converter is presented. The more white noise is injected, the more conducted EMI is reduced. But output-voltage is not sufficiently regulated. This is the reason why carrier frequency selection topology is proposed. In the case of carrier frequency selection, output-voltage of steady state and transient state is fully regulated. A RPWM control method was proposed in order to smooth the switching noise spectrum and reduce it's level. Experimental results are verified by converter operating at 300v/1kW with $5%{\sim}30%$ white noise input. Spectrum analysis is performed on the Phase current and the CM noise voltage. The former is measured with Current Probe and the latter is achieved with LISN, which are connected to the spectrum analyzer respectively.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.75-76
• /
• 2016

This paper proposes a power factor correction circuit with a high efficiency over a wide load range characteristics for a communication power supply. And the characteristic verification is applied to produce a design of prototype. Power factor correction circuit can reduce conduction losses by applying Bridgeless Boost Converter for efficiency. Over a wide load range to maintain the efficient, the control method of a PWM controller is divided by two sections according to the load area. In the low-load region, it was reduced switching losses by applying the critical conduction mode control method. On the other hand, in the heavy-load area, the hysteresis current control method is used to maintain the high efficiency over a wide load range by limiting the peak noise of the inductor.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.263-266
• /
• 1998

ZnO varistors have an excellent non-linearity and a large surge-energy absorption capability. For these reasons, the ZnO varistors are widely used to protect electrical/electronic circuits from an abnormal surge and/or noise signal. In order to obtain the low-voltage varistor with randomly distributed large seed grain within bulk, the ZnO varistors are made by a new three-composition seed grain method. And a conduction mechanism of varistors, which was observed in the temperature range of 30 ∼ 120$^{\circ}C$ and at the current range of 10$\^$-8/∼10$^2$ A/cm$^2$, was classified by the three regions of different mechanism when the current was increased.