• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.497-498
• /
• 2009

Unsaturated polyester(UP) and epoxy resin require 8${\sim}$11 hours long harding times and heating systems used by reinforcement liner. This study is to evaluate the effects of low temperature harding property of UP with methyl methacrylate(MMA) monomer mixing proportions.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.483-484
• /
• 2009

The purpose of this study is to evaluate the compressive behavior of SHCC mixing Fly ash. The parameter of this study are replacement level of fiber and Fly ash.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10b
• /
• pp.915-920
• /
• 2000

The effectiveness of bottom ash on the slump flow, compressive strength of flowable fill is investigated in this study. This study was undertaken on the use of bottom ash as a fine aggregate in flowable fill. Bottom ash is combined with portland cement, fly ash, and water to flowable fill with slump flow(20~30cm). Four different level of bottom ash with fly ash contents, 25%, 50%, 75%, 100% are investigated. Laboratory test results conclude that the inclusion of bottom ash increases the demand for mixing water n obtaining the require slump flow.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1991.10a
• /
• pp.99-106
• /
• 1991

Result of an experimental study on the manufacture, the mechanical properties and waterightness of pitch-based carbon fiber reinforced fly ash.cement composites are presented in this paper. The carbon fiber reinforced fly ash.cement composites using early strength cement, silica powder and a small amount of stylene butadiene rubber latex are prepared with carbon fiber, foaming agents and mixing conditions. As a result, the mechanical and plysical properties such as compresive, tensile and flectural strengths, watertightness and cement composites are improved by using a small amount of stylene butadiene rubber latex.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.11 no.4
• /
• pp.271-280
• /
• 2013

Since the decommissioning of nuclear plants and facilities, large quantities of slightly contaminated concrete waste have been generated. In Korea, the decontamination and decommissioning of the KRR-1, 2 at the KAERI have been under way. And concrete waste was generated about 800 drums of 200 L. The conditioning of concrete waste is needed for final disposal. The concrete waste is conditioned as follows: mortar using coarse and fine aggregates is filled void space after concrete rubble pre-placement into 200 L drum. Thus, this research has developed an optimizing mixing ratio of concrete waste, water, and cement and has evaluated characteristics of a cement waste form to meet the requirements specified in disposal site specific waste acceptance criteria. The results obtained from compressive strength test, leaching test, thermal cycling test of cement waste forms conclude that the concrete waste, water, and cement have been suggested to have 75:15:10wt% as the optimized mixing ratio. Also, the compressive strength of cement waste form was satisfied that including fine powder up to maximum 40wt% in concrete debris wastes about 75%. As a result of scale-up test, the mixture of concrete waste, water, and cement is 75:10:15wt% meet the satisfied compressive strength because the free water increased with and increased in particle size.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.11a
• /
• pp.38-39
• /
• 2013

In this study, in regard to fiber reinforced mortar mixing steel fiber and 4types of organic fiber, impact test was carried out. Because to predict fracture reduction performance with flexural, tensile strength when types of fiber were different as impact reduction performance of concrete is closely related with toughness such as flexural strength, tensile strength and fracture energy etc. As a result, enhancement of toughness by fiber reinforcement controls the spall of rear. On the other hand in case of steel fiber relatively turned up high toughness in appropriate load compared with organic fiber but in same mixing rate, impact reduction performance by projectile showed low performance due to few number of an individual of mixing.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.11a
• /
• pp.127-128
• /
• 2020

This research is part of the research for unifying the mass concrete and utilizing the rate of super retarding agent. We analyzed the performance of super retarding agent 20℃ conditions. It was found that there was no deterioration in fluidity and air quality due to the change in the super retarding agent mixing rate. It was found that when super retarding agent was mixed up to 0.5 %, it was delayed for 22.3 hours at 20℃. Therefore in order to ensure the performance required at the site, the super retarding agent mixing rate must be determined by fully considering the situation at the site. In addition it will be analyzed that super retarding agent performance analysis at high temperature will be required in subsequent studies.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.05a
• /
• pp.45-46
• /
• 2023

CLC is used as a filling material for many buildings, and according to energy saving design standards, CLC also requires insulation performance. However, it shows lower insulation performance compared to organic insulation, so additional research is needed. Therefore, in this study, the insulation properties of CLC were analyzed by incorporating EPS beads with high insulation performance into CLC. In this experiment, EPS beads and blast furnace slag were replaced, and W/B was fixed at 33%. The EPS Bead mixing ratio was divided into 5 levels: 0, 0.5, 1.0, 1.5, 2.0 (%), and the experimental items were measured for apparent density and thermal conductivity. As a result of the experiment, the apparent density and thermal conductivity tended to decrease as the mixing ratio of EPS beads increased. It is judged that the density decreased due to the low density and the micropores inside, and the thermal conductivity also decreased.

• Journal of the Korea Institute of Building Construction
• /
• v.3 no.1
• /
• pp.115-122
• /
• 2003

In order to analyze liquidity change according to increasing the charge of superplasticizer, we inputted charges by dividing into six steps, 0% through 1.25%; at the same time, to observe liquidity change according to the change of charge-time, we carried out the experiment applying 30-minute intervals, i.e. at beginning of mixing, 30, 60 and 90 minutes. The results are below. 1) According to increasing the charge of superplasticizer, the liquidity of concrete was enhanced, however, when inputted 1.25%, a little segregation was occurred, which allowed us to make a conclusion that concrete performance would be deteriorated due to this segregation. 2) When we inputted 1.25% of superplsticizer, steady liquidity features were shown regardless of the charge-time of concrete, which allowed us to make a conclusion that this input would be the best for liquidity performance considering only liquidity features. 3) After analyzing the dynamical features of liquid concrete, the result showed that there was not significant effect on revelation of compressive strength. We concluded form this result that there was no influence on the stripping-time of a mold form. 4) When we charge superplasticizer in concrete more than 1%, we, in advance, should clearly judge the concrete performance required during constructing in site, as it were, the compressive strength or liquidity etc.; furthermore, we had better decide a charge and input-time of superplasticizer to meet the required performance.

• Computers and Concrete
• /
• v.17 no.3
• /
• pp.337-351
• /
• 2016

This paper presents the properties of pervious concrete containing high-calcium fly ash. The water to binder ratios of 0.19, 0.22, and 0.25, designed void ratios of 15, 20, and 25%, and fly ash replacements of 10, 20, and 30% were used. The results showed that the use of fly ash as partial replacement of Portland cement enhanced the mixing of paste resulting in a uniform mix and reduced amount of superplasticizer used in the mixture. The compressive strength and flexural strength of pervious concrete were slightly reduced with an increase in fly ash replacement level, while the abrasion resistance increased due mainly to the pozzolanic and filler effects. The compressive strength and flexural strengths at 28 days were still higher than 85% of the control concrete. The aggregate size also had a significant effect on the strength of pervious concrete. The compressive strength and flexural strength of pervious concrete with large aggregate were higher than that with small aggregate.