• Corrosion Science and Technology
• /
• v.22 no.4
• /
• pp.273-286
• /
• 2023

Rebar is embedded in concrete to create reinforced concrete (RC). Rebar carries most of the tensile stress and gives compressively loaded concrete fracture resistance. However, embedded steel corrosion is a significant cause of concern for RC composite structures worldwide. It is one of the biggest threats to concrete structures' longevity. Due to environmental factors, concrete decays and reinforced concrete buildings fail. The type and surface arrangement of the rebar, the cement used in the mortar, the dosing frequency of the concrete, its penetrability, gaps and cracks, humidity, and, most importantly, pollutants and aggressive species all affect rebar corrosion. Either carbonation or chlorides typically cause steel corrosion in concrete. Carbonation occurs when carbon dioxide in the atmosphere combines with calcium within the concrete. This indicates that the pH of the medium is falling, and the steel rebar is corroding. When chlorides pass through concrete to steel, corrosion rates skyrocket. Consideration must be given to concrete moisture. Owing to its excellent resistance, dry concrete has a low steel corrosion rate, whereas extremely wet concrete has a low rate owing to delayed O₂ transfer to steel surfaces. This paper examines rebar corrosion causes and mechanisms and describes corrosion evaluation and mitigation methods.

• International conference on construction engineering and project management
• /
• 2009.05a
• /
• pp.794-799
• /
• 2009

The temperature control of in-place concrete is the most important factor for an early age of curing concrete. Heat stress of mass concrete caused by the heat of hydration can induce the crack of concrete, and a frost damage from cold weather casting concrete results defect on compressive strength and degradation of durability. Therefore, success and failure of concrete work is dependant on the measurement and control of concrete temperature. In addition, the compressive strength assessment of in-place concrete obtained from the maturity calculated from the history of temperature make a reduction of construction cycle time, possible. For that purpose, wireless temperature measuring system was developed to control temperature and assess strength of concrete. And, it was possible to monitor the temperature of concrete over 1km apart from site office and to take a proper measure; mesh-type network was developed for wireless sensor. Furthermore, curing control system that contains the program capable to calculate the maturity of concrete from the history of temperature and to assess the compressive strength of concrete was established. In this study, organization and practical method of developed curing control system are presented; base on in-place application case.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.655-660
• /
• 2002

Major deterioration in concrete structures are salt attack and carbonation. Especially severe problems due to carbonation occur in tile concrete structures of city, tunnel, underground structures. Cracks in concrete during service life including early age due to hydration heat and/or shrinkage accelerate the diffusion of concrete so that the deterioration is also accelerated. In this study, carbonation depths of both non-cracked concrete and cracked concrete are evaluated and weight change test and TGA are carried out. Through the tests, a relation between water-cement ratio and carbonation depth is derived and also carbonation increase rate is derived in the function of crack width.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10a
• /
• pp.336-341
• /
• 1998

Steel fiber reinforced concrete(SFRC) is a composite material possessing many physical and mechanical properties which are distinct from unreinforced concrete. The use of steel fiber reinforcement to improve the flexural and tensile strengths, extensibility and toughness of ordinary cement concrete is well known at present, but reinforcement of polymer concrete with steel fibers has been hardly reported untill now. The objective of this study was to improve the properties of the polymer concrete by addition of steel fibers. In this paper steel fiber reinforced polymer concrete is prepared with various steel fiber contents and aspect ratio($\ell$ /d), and their mechanical properties were investigated experimentally.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.585-588
• /
• 1999

This study is performed to verify the effect of CSA expansive additives for concrete by material properties test and 4 point-bendig test of RC slabs. The result shows that the variations of compress strength, bending strength, and modulus of elasticity of expansive concrete are the same as those of plain concrete. And the crack load of RC slabs with expansive concrete are increased in comparision with that of plain concrete, but the ultimate strength of RC slabs with expansive concrete is decreased.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.249-252
• /
• 1999

Recently, the use of lightweight concrete in architectural structures are increasing. It is considered important to control the quality of lightweight concrete. The purpose of this study is to find mechanical properties of lightweight concrete using the expanded clay. Thus, slump, air content, compressive strength, splitting tensile strength, length change ratio, unitweight change ratio and absorption of lightweight concrete have been investigated. As a result, it was shown that proper expanded clay replaced by coarse aggregate in concrete was considered as a good replacement of lightweight concrete.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.77-80
• /
• 1999

Before the field applications, several basic laboratory test were the characteristics of workability and strength of the concrete containing CSA expansive additive. As a result, high strength concrete using CSA expansive additive show similar workability and compressive to that of plain concrete, the optimum replacement ratio of them to plain concrete were obtained for CSA expansive additive 10%. On the other hand, it can be concluded that the use of CSA component is effective to prevent shrinkage crack reducing concrete using superplasticizer and to achive volume stability of concrete structure.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.801-804
• /
• 1999

The interest in workability and quality control of concrete is increasing as to improve quality of concrete structure according to industrialization. Therefore, it is the aim of this study to evaluate the quality of flowing concrete and systematize quality control by analyzing the data of the quality control of concrete through a basic quality control system for improvement of the concrete in pumping flowing concrete for construction industy.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10c
• /
• pp.167-172
• /
• 1998

The purpose of this study is recycling of ready mixed concrete sludge as artificial aggregate by product technique of artificial aggregate in the normal temerature. For the qulity test of artificial aggregate using ready mixed concrete sludge, it is tested in the various aspect. Therefor, Quality of artificil aggregate is suitable as coarse aggregate except absoption, abrasion. For the application of aggregate in cement concrete, Coarse aggregate are replaced with artificial aggregate using ready mixed concrete sludge 100% of volume. The results of test shown that the artificial aggregate using ready mixed concrete sludge could be used replacement of coarse aggregate in cement concrete.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.935-938
• /
• 2001

This paper reports the relation of concrete setting characteristic and lateral pressure in mass concrete wall such as side wall of LNG underground storage tank. In order to estimate the lateral pressure, initial setting time of low heat cement concrete with type of mineral admixture was measured for three concrete mixtures(W/P=41.6%) containing limestone powder, fly ash, and slag powder. As a result, the lateral pressure of the concrete containing limestone powder was the smallest than those of other concretes as well as the initial setting time.