• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.14 no.2
• /
• pp.113-122
• /
• 2016

In this study, the dispersion process of pollutant substances in a port under wave and current environments was evaluated by a hydraulic experiment. Once the contaminants washed ashore into the port of Wolseong nuclear power plant, transport processes of pollutants were investigated by tracking the tracer according to the variations of experimental condition through a hydraulic experiment. Several hydraulic experiments were performed to analyze the pollutant discharge rate of the surface coming from the different coastal environments. From the hydraulic experiment results, the tracer concentration decreased exponentially. These results suggested that, after the tracer was transported to the open sea, a different gradient was shown under different conditions. For the case of a diluted condition, the half-life of flow rate was 2.70, 10.40, and 26.39 days for 30, 20 and 10 rpm in the left-side, respectively. The decrease of the tracer concentration under conditions of 30 rpm was much faster than that under conditions of 10 rpm. For the wave condition, the half-life of flow rate was 4.59 and 15.35 days for the right and left side of the port in a hydraulic scale prototype, respectively.

• Elastomers and Composites
• /
• v.41 no.2
• /
• pp.116-124
• /
• 2006

Cloud-point data to $160^{\circ}C$ and 1,000 bar are presented with poly(ethylene-co-15.3 mole% octene) copolymers ($PEO_{15}$) in pure 1-octene and mixtures of ethylene - 1-octene. The cloud-point curves for $PEO_{15}$ - ethylene - 1-octene mixture dramatically increase in pressure to as high as 1,000 bar with an increasing ethylene concentration. At ethylene concentrations less than 18 wt%, the ternary mixture has bubble- and cloud-point curves. As the ethylene concentration of the ternary mixture increases, the bubble-point curve and the single-phase region reduce. The reduction in the single phase region with increasing ethylene concentrations is the result of reduced dispersion interactions between $PEO_{15}$ and the mixed solvent. The single-phase region decreases with increasing temperatures when ethylene concentrations are lower than 36 wt%, whereas the single-phase region increases with temperatures at ethylene concentrations greater than 50 wt%. At ethylene concentrations greater than 50 wt% the effect of the polar interactions of the mixed solvent, which is unfavorable to dissolve PEO, is greater than the effect of the density of the mixed solvent. Therefore, the cloud-point pressures increase with a decreasing temperature. However, at ethylene concentrations less than 50 wt%, the cloud-point pressures decrease with temperature, because the effect of the polar interactions is less than the density effect.

• Elastomers and Composites
• /
• v.44 no.3
• /
• pp.336-342
• /
• 2009

We measured shear viscosity of polystyrene (PS) and poly(butyl methacrylate) (PBMA) particles, with a capillary rheometer, prepared by suspension polymerization with 1.0 wt% hydrophobic silica as a stabilizer by varying the initiator concentration at $75^{\circ}C$. PS particles with weight average molecular weight of 66,500 g/mol displayed a Newtonian behaior at low shear rates at $190^{\circ}C$. With increasing molecular weight, PS particles showed shear thinning over the entire range of shear rates. For PBMA particles, steady shear measurement was carried out at $170^{\circ}C$. PBMA particles with weight average molecular weight of 156,700 g/mol showed a Newtonian behaior only at low shear rates. PBMA particles also showed shear thinning with an increase in molecular weight and its pattern similar to that of PS. When carbon black was incorporated into PS and PBMA polymers, steady shear measurement was conducted at $170^{\circ}C$. An increase in carbon black concentration in PS and PBMA composite particles exhibited a progressive increase in shear viscosity. The increase in shear viscosity, however, was less pronounced compared to an increase as a function of molecular weight. Preparing PS composites containing carbon black by internal mixing resulted in an increase in shear viscosity. Its increase, however, was found to be less than that shown in PS composite particles. We speculate that this is caused by an enhanced dispersion of carbon black particles with an internal mixer. Yield behavior was not observed in any of the samples we selected in this experiment.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.4C
• /
• pp.231-238
• /
• 2008

A column testing device capable of measuring the electrical resistivity of soil at 3 different locations was developed to verify applicability of bulk electrical conductivity (BEC) breakthrough curves in monitoring contaminant transport. Tracer injection tests were conducted with three different types of saturated sands to obtain average linear velocities and longitudinal hydrodynamic dispersion coefficients based on BEC breakthrough curves and effluent solute breakthrough curves. Comparative analysis of transport parameters obtained from curve fitting the results into the analytical solutions confirmed the validity of resistance measurements in estimating time-continuous resident solute concentration. Under the assumption that a linear relationship exists between ${\sigma}_{sat}-{\sigma}_w-C$, the BEC breakthrough curves are able to effectively reduce the laborious and time-consuming processes involved in the conventional method of sampling and analysis. In order to reduce possible uncertainties in analyzing the BEC breakthrough curves, it was recommended that resistance measurements take place nearby the effluent boundary. In addition, a sufficient electrical contrast or difference in the electrical conductivity of the influent and the saturating solution is required to conduct reliable analysis.

• Journal of the Korean earth science society
• /
• v.44 no.3
• /
• pp.196-209
• /
• 2023

The Nishinoshima volcano, located 940 km south of Tokyo, experienced an eruption from June to August 2020. The volcanic gas and ash from the eruption of Nishinoshima that occurred at the end of July 2020 was reported to have the potential to affect the Korean Peninsula. In this study, we used Ash3D, a numerical simulation program for volcanic ash dispersion, to investigate the eruption that occurred at 0:00 local time on July 28, 2020, with a volcanic explosivity index of three. The results showed that the volcanic ash cloud reached Okinawa on the morning of July 30, carried by an east wind. It then moved northward and reached Jeju Island on August 1, eventually circulating in a clockwise direction and reaching southern part of the Korean Peninsula on August 2. The concentration of Particulate Matter 10 (PM₁₀), measured at the Jeju Gosan Meteorological Observatory in Jeju Island, increase from August 1. A similar increase in PM₁₀ concentration was observed at the Gudeok Mountain Weather Station in Busan from August 2. These findings suggested that eruption of the Nishinoshima volcano had an impact on the fine dust concentrations at Jeju Island and southern part of the Korean Peninsula.

• Journal of Biosystems Engineering
• /
• v.13 no.4
• /
• pp.38-45
• /
• 1988

The freeze drying of garlic juice was carried out in a vacuum freeze dryer, laboratory size, by backface heating. The factors which influence the rate of freeze drying, the pressure of drying chamber, the plate temperature, the concentration and the thickness of a sample, were discussed in this study. The drying rate was in proportion to the drying chamber pressure and when the pressure was at 1.5 torr, the foaming occured on the surface of materials, so this condition was not suitable for freeze drying. As the temperature of plate increased, drying rate increased, but when the temperature was $20^{\circ}C$, it was impossible to accomplish freeze drying because the foaming and the dispersion occured in a sample. The higher the concentration of a sample was, the lower drying rate was.

• Korean Chemical Engineering Research
• /
• v.47 no.4
• /
• pp.453-458
• /
• 2009

Recently, new methods to synthesize and process polymers without toxic organic solvents are needed in order to solve environmental problems. The use of supercritical carbon dioxide as a solvent for the polymer synthesis is attractive since it is non-toxic, non-flammable, naturally abundant, and the product may be easily separated from the solvent. In this study, we developed the method using super critical $CO_2$ to prepare P(MAA-co-EGMA) hydrogel nanoparticles as an intelligent drug delivery carrier. The effects of concentrations of PtBuMA-PEO as a dispersion stabilizer and AIBN as an initiator on the particle synthesis were investigated. When PtBuMA-PEO concentration increased, the particle size decreased. However, there was no significant difference in the particle size according to the AIBN concentration. There was a drastic change of the equilibrium weight swelling ratio of P(MAA-co-EGMA) hydrogel nanoparticles at a pH of around 5, which is the $pK_a$ of PMAA. At a pH below 5, the hydrogels were in a relatively collapsed state but at a pH higher than 5, the hydrogels swelled to a high degree. In release experiments using Rh-B as a model solute, the P(MAA-co-EGMA) hydrogel nanoparticles showed a pH-sensitive release behavior. At low pH(pH 4.0) a small amount of Rh-B was released while at high pH(pH 6.0) a relatively large amount of Rh-B was released from the hydrogels.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2001.04a
• /
• pp.98-103
• /
• 2001

In order to understand the characteristics of leachate at the Seokdae municipal waste landfill in the Pusan city, the correlation between leachate pollution loading and volume of gas production. concentration of gas and subsidence of ground, the characteristical methos, geochemical analyses and laboratory column tests using samples of gases, leachate and surface soil of Seokdae waste landfill area. Through the analysis of water balance, leachate flow rate and pollution loading were estimated. Geistatistical analysis of four gas components ( $O_2$, C $H_4$, $H_2$S and CO) shows the possibility of ground subsidence around the group of a site with high concentration of gas. From geochemical analyses of leachate, EC and Total-Alkalinity of ground subsidence around the group of a site with high concentration of gas. From geochemical analysis of leachate, Ec and Total-Alkalinity were increased, and Cl, Cr, Mn, Cu, Zn, Cd and Pb were decreassed comparing to the part, and the type of water quality was Na-HC $O_3$ in trilinear diagram. It shows that biodecomposition of municipal wastes continues actively. From the analysis of water balance, the total leachate flow rate is about 465.11㎥/day and pure pollution loading of Cl, Mn and Fe are estimated to 223.8kg/day, 0.2kg/day, 0.3kg/day, respectively. The laboratory column test of residual soil and landfill soil shows 0.206cm and 0.019cm for linear velocity(equation omitted), 0.234 $\textrm{cm}^2$/min and 0.018$\textrm{cm}^2$/min for diffusion coefficient ( $D_{ι}$), and 1.136cm and 0.095cm longitudinal dispersion index ($\alpha$$_{ι}$), respective]y. It demonstrates that the delay time of contamination for residual soil is shorter than that of landfill soil.

• Journal of the Korean Geographical Society
• /
• v.30 no.2
• /
• pp.146-168
• /
• 1995

problems involved in defining and identifying it. However, data on ownership of business establishments may be useful and one of the best alternatives for this empirical research because of use of limited information about control This study examines the spatial patterns of external control in the Korean manufacturing activities between 1986 and 1992. Using the data on ownership iinkages of multilocational firms between 15 administrative areas, it was possible to construct a matrix of organizational control in terms of the number of establishments. The control matrix was disaggregated by three types of manufacturing industries according to the capital and labor requirements of production processes used in. On the basis of the disaggregated control matrix, a series of measures were calculated for investigating the magnitude and direction of control as well as the external dependency. In the past decades Korean industrialization development has risen at a rapid pace, deepening integration into the world economy, together with the continuing growth of the large industrial firms. The expanded scale of large firms led to a spatial separation of production from control, Increasing branch plants in the nation. But recent important changes have occurred in the spatial organization of production by technological development, increasing international competition, and changing local labor markets. These changes have forced firms to reorganize their production structures, resulting in changes of the organizational structures in certain industries and regions. In this context the empirical analysis revealed the following principal trends. In general term, the geography of corporate control in Korea is marked by a twofold pattern of concentration and dispersion. The dominance of Seoul as a major command and control center has been evident over the period, though its overall share of allexternally controlled establishments has decreased from 88% to 79%. And the substantial amount of external control from Seoul has concentrated to the Kyongki and Southeast regions which are well-developed industrial areas. But Seoul's corporate ownership links tend to streteh across the country to the less-developed regions, most of which have shown a significant increase of external dependency during the period 1986-1992. At the same time, a geographic dispersion of corporate control is taking place as Kyongki province and Pusan are developing as new increasingly important command and control reaions. Though these two resions contain a number of branch plants controlled from other locations, they may be increasingly attractive as a headquarters location with increasing locally owned establishments. The geographical patterns of external control observable in each of three types of manufacturing industries were examined in order to distinguish the changing spatial structures of organizational control with respect to the characteristics of the production processes. Labor intensive manufacturing with unskilled iabor experienced the strongest external pressure from foreign competition and a lack of low cost labor. The high pressure expected not only to disinte-grate the production process but also led to location of production facilities in areas of cheap labor. The linkages of control between Seoul and the less-developed regions have slightly increased, while the external dependency of the industrialized regions might be reduced from the tendency of organizational disintegration. Capita1 intensive manufacturing operates under high entry and exit barriers due to capital intensity. The need to increase scale economies ied to an even stronger economic and spatial oncentration of control. The strong geographical oncentration of control might be influenced by orporate and organizational scale economies rather than by locational advantages. Other sectors experience with respect to branch plants of multilocational firms. The policy implications of the increase of external dependency in less-developed regions may be negative because of the very share of unskilled workers and lack of autonomy in decision making. The strong growth of the national economy and a scarcity of labor in core areas have been important factors in this regional decentralization of industries to less-developed regions. But the rather gloomy prospects of the economic growth in the near future could prevent the further industrialization of less-developed areas. A major rethinking of regional policy would have to take place towards a need for a regional policy actively favoring indigenous establishments.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.8 no.4
• /
• pp.357-368
• /
• 2003

Time-series CTDT (Conductivity/Temperature/Depth/Transmissivity) were obtained at one point near tidewater glacier of Marian Cove (King George Islands, Antarctica) to present water column properties and SPM (suspended particulate matter) dispersal pattern in relation with tide, current, meteorological data, and SPM concentration. Four layers were divided from the water column characteristics measured in the interval of an hour for about 2 days: 1) cold, fresh, and turbid surface mixed layer between 0-20 m in water depth, 2) warm, saline, and relatively clean Maxwell Bay inflow between 20-40 m in water depth, 3) turbid/cold tongue of subglacial discharges compared with the ambient waters between 40-70 m in water depth, and 4) cold, saline, and clean bottom water beneath 70 m in water depth. Surface plume, turbid freshwater at coastal/cliff area in late summer (early February), had the characteristic temperature and SPM concentration according to morphology, glacial condition, and composition of sediments. The restrict dispersion only over the input source of meltwater discharges was due to calm wether condition. Due to strong wind-induced surface turbulence, fresh and turbid surface plume, englacial upwelling cold water, glacier-contact meltwater, and Maxwell Bay inflow was mixing at ice-proximal zone and the consequent mixed layer deepened at the surface. Large amount of precipitation, the major controlling factor for increasing short-term glacial discharges, was accompanied by the apparent development of subglacial discharge that resulted in the rapid drop of salinity below the mid depth. Although amount of subglacial discharge and englacial upwelling may be large, however, their low SPM concentration would have small influence on bottom deposition of terrigenous sediments.