• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.628-631
• /
• 2004

In this paper, mechanical properties of concrete incorporating CKD are discussed with W/B and fluidity. For setting properties, an increase in W/B retarded setting time greatly in $5^{\circ}C$, while accelerated in $20^{\circ}C$. For fluidity, an increase in slump delayed the setting time with dosage of SP agent. The presence of CKD has little influence on setting time compared with plain concrete. For compressive strength, an increase in maturity enhanced compressive strength. Fluidity had no relation to compressive strength. At low curing temperature, concrete with CKD has slight strength loss compared with plain concrete. However, remarkable strength loss at low curing temperature in early stage was not found, which can be applicable to low temperature environment concrete placing.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.11a
• /
• pp.23-24
• /
• 2019

In this paper, the compressive strength characteristics of cement paste were compared with the addition of liquefied red mud with the addition of nitric acid in order to improve the strength of the deteriorated cement. The results showed that the compressive strength with between 7 days and 28 days was greater than that of liquefied red mud. The ratio of daily compressive strength of the liquefied red mud is higher than that of the Plain with a 1 percent addition rate, and the ratio of compressive strength is lower than that of the Plain on the 28 days. Therefore, the compressive strength of neutralization liquefied red mud compared to liquidated red mud was relatively high, and the compressive strength of the red mud was shown to be improved to a level almost similar to that of Plain.

• Computers and Concrete
• /
• v.12 no.1
• /
• pp.53-64
• /
• 2013

The curing temperature is known to influence the rate of mechanical properties development of early age concrete. In realistic sites the temperature of concrete is not isothermal $20^{\circ}C$, so the paper measured adiabatic temperature increases of four different concretes to understand heat emission during hydration at early age. The temperature-matching curing schedule in accordance with adiabatic temperature increase is adopted to simulate the situation in real massive concrete. The specimens under temperature-matching curing are subjected to realistic temperature for first few days as well as adiabatic condition. The mechanical properties including compressive strength, splitting strength and modulus of elasticity of concretes cured under both temperature-matching curing and isothermal $20^{\circ}C$ curing are investigated. The results denote that comparing temperature-matching curing with isothermal $20^{\circ}C$ curing, the early age concretes mechanical properties are obviously improved, but the later mechanical properties of concretes with pure Portland and containing silica fume are decreased a little and still increased for concretes containing fly ash and slag. On this basement using an equivalent age approach evaluates mechanical properties of early age concrete in real structures, the model parameters are defined by the compressive strength test, and can predict the compressive strength, splitting strength and elasticity modulus through measuring or calculating by finite element method the concreted temperature at early age, and the method is valid, which is applied in a concrete wall for evaluation of crack risking.

• Advances in materials Research
• /
• v.8 no.2
• /
• pp.103-115
• /
• 2019

Polypropylene (PP) fibers for making fabric which is used for packing cement have a high strength and high tear resistance. Due to these excellent properties the present study investigates the effect of PP fibers on the mechanical strength of concrete. Mechanical strength parameters such as compressive strength, splitting tensile strength and flexural strength are evaluated. Structural integrity of concrete using Ultrasonic Pulse Velocity (UPV) was also studied. Concrete containing PP fibers in percentage of 0%, 0.15%, 0.25%, 0.5% and 0.75% was developed with a characteristic compressive strength of 25 MPa. Concrete cubes, cylinder and prismatic specimens were cast and tested. It was found that the UPV values recorded for all specimens were of the similar order. Test results indicated the used of PP fibers can significantly improve the flexural and splitting tensile strengths of concrete materials whereas it resulted a decreased in compressive strength. The relative increase in split tensile and flexural strength was optimum at a fiber dosage of 0.5% and a mild decreased were observed in 28 days compressive strength. The findings in this paper suggested that PP fibers deriving from these waste cement bags are a feasible fiber option for fiber-reinforced concrete productions.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.04a
• /
• pp.83-88
• /
• 1998

II-anhydrite, slag, and fly ash produced as industrial by-product were reutilized for the manufacture of high strength admixtures for cement and concrete. The effects of these admixtures on the compressive strength of cement mortar and concrete were examined with those of domestic admixture. At the condition mortar and concrete. Especially, adding of II-anhydrite was very effective for the increasing of compressive strength. Therefore it is possible that these admixture as a high strength admixture apply to cement and concrete.

• Computers and Concrete
• /
• v.20 no.3
• /
• pp.283-290
• /
• 2017

The aim of this study is to investigate the effect of the bond strength of self-compacting mortars (SCMS) produced from ground pumice powder (GPP) as a mineral additive. In this scope, six series of mortars including control mix were prepared that consist of 7%, 12%, 17%, 22% and 27% of ground pumice powder by weight of cement. A total of 54 specimens of $40{\times}40{\times}160mm$ were produced and cured at the age of 3, 28 and 90-day for compressive and tensile strength tests and 18 specimens of $150{\times}150{\times}150mm$ mortar were prepared and cured at 28 days for bond strength tests. Flexural tensile strength and compressive strength of $40{\times}40{\times}160mm$ specimens were measured at the curing age of 7, 28 and 90-day. Mini V-funnel flow time and mini slump flow diameter tests were also conducted to obtain rheological properties. As a result of the study, it was observed that the SCMs containing 12% of GPP has the highest bond strength as compared to control and GPP mortars. Compressive strength slightly increased up to 12% of GPP.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.44 no.1
• /
• pp.116-124
• /
• 2002

Natural resources fur the construction materials such as good soil, sand, and coarse aggregates have been encountered to be short due to excessive use by human. Even though some soil has been found to be unsuitable for construction materials, soil with reinforcement can naturally be an answer to these alternatives. According to recently published papers on fiber mixed soil, fiber mixed with soil can improve shear strength, compressive strength and post-peak load strength retention. In this study, a series of tests were performed to clarify the characteristics of fiber mixed soil and to give basic data for design and construction and their engineering properties, that is, unconfined compressive strength, splitting tensile strength, shear strength, crack by drying, freeze-thaw, creep and Poisson\`s ratio, were investigated and analyzed. It has been shown that fiber mixed soil is one of good alternatives fur the civil and building construction materials.

• Geomechanics and Engineering
• /
• v.17 no.2
• /
• pp.195-206
• /
• 2019

The gypsiferous soils are significantly sensitive to moisture and the water has a severe destructive effect on them. Therefore, the effect of lime and silica fume addition on their mechanical properties, when subjected to water, is investigated. Gypsiferous soil specimens were mixed with 1, 2 and 3% lime and 1, 3, 5 and 7% silica fume, in terms of the dry weight of soil. The specimens were mixed at optimum moisture content and cured for 24 hours, 7 and 28 days. 86 specimens in the sizes of unconfined compression strength test mold were prepared to perform unconfined compressive strength and durability tests. The results proved that adding even 1% of each of these additives can lead to a 15 times increase in unconfined compressive strength, compared with untreated specimen, and this increases as the curing time is prolonged. Also, after soaking, the compressive strength of the specimens stabilized with 2 and 3% lime plus different percentages of silica fume was considerably higher than before soaking. The durability of the treated specimens increased significantly after soaking. Direct shear tests showed that lime treatment is more efficient than silica fume treatment. Moreover, it is concluded that the initial tangent modulus and the strain at failure increased as the normal stress of the test was increased. Also, the higher lime contents, up to certain limits, increase the shear strength. Therefore, simultaneous use of lime and silica fume is recommended to improve the geotechnical properties of gypsiferous soils.

• Computers and Concrete
• /
• v.17 no.4
• /
• pp.523-539
• /
• 2016

Alkali-activated binder (AAB) is increasingly being considered as an eco-friendly and sustainable alternative to portland cement (PC). The present study evaluates 30 different AAB mixtures containing fly ash and/or slag activated by sodium hydroxide and sodium silicate by correlating their properties from micro to specimen level using regression. A model is developed to predict compressive strength of AAB as a function of volume fractions of microstructural phases (physicochemical properties) and ultrasonic pulse velocity (elastic properties and density). The predicted models are ranked and then compared with the experimental data. The correlations were found to be quite reasonable (R2 = 0.89) for all the mixtures tested and can be used to estimate the compressive strengths for similar AAB mixtures.

• Journal of the Korea Institute of Building Construction
• /
• v.16 no.1
• /
• pp.53-58
• /
• 2016

In order to investigate the feasibility of municipal solid waste incineration ash melted slag powder as admixture, an experimental study was performed on cement mortar with municipal solid waste incineration ash melted slag powder. Fresh mortar properties and strength properties with various municipal solid waste incineration ash melted slag powder replacement ratios were estimated. There replacement ratio adopted in this study was 0, 10, 20, 30, 40, 50%. After then flow properties was considered as properties of fresh mortar. And compressive strength was determined 3, 7, 14, 28, 56 days for the hardened mortar specimens. According to the test results, the flow of mortar was increased with in replacement amount of municipal solid waste incineration ash melted slag powder. Furthermore, compressive strength at early age was decreased, whereas the compressive strength at the age of 28, 56day was increased.