• Journal of the Korean Mathematical Society
• /
• v.48 no.1
• /
• pp.83-104
• /
• 2011

In this note, compound-commuting additive maps on matrix spaces are studied. We show that compound-commuting additive maps send rank one matrices to matrices of rank less than or equal to one. By using the structural results of rank-one nonincreasing additive maps, we characterize compound-commuting additive maps on four types of matrices: triangular matrices, square matrices, symmetric matrices and Hermitian matrices.

• Journal of the Korean Solar Energy Society
• /
• v.34 no.6
• /
• pp.85-92
• /
• 2014

This study carried out experimental on the cooling characteristics of clathrate compound including TMA(Tri-Methyl-Amine ; $(CH_3)_3N$) as a low temperature latent heat storage material. And additive was used for subcooling improvement of TMA-water clathrate compound. The conclusion of above study is as following ; TMA 25wt%-water clathrate compound is shown stable phase change and low subcooling degree. The subcooling was improved in the case ethanol($CH_3CH_2OH$) 0.5wt% is added to TMA 25wt%-water clathrate compound.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.4
• /
• pp.557-562
• /
• 2008

In this paper, experiments have been performed for the investigation of tribological characteristics of automobile gear oil with the addition of ZDDP and DEP by using the FALEX WEAR TEST MACHINE. The results are as follows. The wear characteristics of gear oil was improved by adding compound additives. The extreme pressure of gear oil increases and then decreases with the applied load. The maximum extreme pressure of gear oil with compound additive is bigger then that of pure gear oil. The friction coefficient of pure gear oil monotonically increases with the temperature, but that of gear oil mixed with the additives decreases at the high temperature.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.16 no.12
• /
• pp.1212-1217
• /
• 2004

This study investigated the improvement effect of a small portion of surfactant on the supercooling and the phase change temperature of TMA 30 wt% clathrate compound when surfactant is added to the clathrate compound. The experiments are carried out under various conditions; the concentration of additive ranges between 0.08～0.12 wt% and the temperature of heat source ranges between -8 and -6$^{\circ}C$. The experimental results show that the phase change temperature with the surfactant of 0.1 wt% is lower by 1$^{\circ}C$ than TMA 30 wt% and the supercooling is reduced by 1$0^{\circ}C$.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.1
• /
• pp.41-47
• /
• 2012

The LDS(Laser Direct Structuring) is one of the new direct writing methods to fabricate conductive patterns by energy beam. It uses thermoplastic polymers with an additive compound that serves as plating seed after the activation by laser. The advantages of LDS include the miniaturization of electrical components, design flexibility, and a reduced number of production steps. The purpose of this study is to investigate the fundamental mechanism for LDS and the characteristics of conductive patterns by laser parameters. These results were studied by SEM, EDX, and XPS analysis. We have used a 20W pulse-modulated fiber laser and copper electroless plating to fabricate conductive patterns on polymer. The result showed that electroless copper plating seed caused the laser cracking of additive compound. In particular, the additive compound contained in copper metal oxides atoms will be changed to copper metal elements. Also, the characteristics of conductive patterns were dependent on laser parameter, especially laser fluence.

• Korean Journal of Materials Research
• /
• v.25 no.11
• /
• pp.590-597
• /
• 2015

In this article, poly methyl triethoxy silane was compounded with an inorganic waterproof admixture at a certain ratio to improve the performance of gypsum products; a new type of high-efficiency compound water-proofing additive was also investigated. Furthermore, the waterproof mechanism and the various properties on the hardened gypsum plaster were investigated in detail by XRD and SEM. The results show that the intenerate coefficient of gypsum plaster increased to more than 0.9; the water absorbing rate decreased to less than 10 %. Both the bending strength and the compressive strength of gypsum plaster increased by various degrees. The intenerate coefficient reached a maximum value of 0.73 and the strength of the samples showed almost no change when 5% cement alone was added. In this new type of the high-efficiency compound with waterproof additive, the optimal technological parameters for formulas were obtained to be: 5% cement, 18 % mineral powder, and 0.8% poly methyl triethoxy silane, to compound gypsum plaster. Meanwhile, the production of high performance gypsum as a building material has become possible.

• Proceedings of the SAREK Conference
• /
• 2005.11a
• /
• pp.392-397
• /
• 2005

This study is investigated the supercooling improvement and the phase change temperature of the TMA clathrate compound including TMA(Tri-Methyl-Amine, ($(CH_3)_3N$) of 25 wt% with additive as a low temperature storage material at $6^{\circ}C$ and $-7^{\circ}C$ of heat source. The additive is ethanol of 0.1, 0.3 wt% and 0.5 wt%. The results showed that as the concentration of ethanol is increased, the phase change temperature, the degree of supercooling and the retention time of liquid phase are decreased. Especially, TMA 25 wt% clathrate compound with ethanol of 0.5wt% has the average of phase change temperature of $3.8^{\circ}C$, degree of supercooling of $0.9^{\circ}C$, $0.8^{\circ}C$ and retention time of liquid phase for 6, 5 minutes at $-6^{\circ}C$, $-7^{\circ}C$ of heat source. From the results of this study, TMA 25wt% clathrate compound with ethanol 0.5wt% showed supercooling repression effect.

• Fibers and Polymers
• /
• v.2 no.4
• /
• pp.190-195
• /
• 2001

Additives, such as sodium perborate and borax, were examined in dialdehyde wrinkle resistant finishing of cotton. Results indicated that the whiteness index(WI) of cotton treated with dialdehyde and additive showed about 90% of WI of the untreated cotton but with decrease in wrinkle recovery angle (WRA) due to inhibition effect of these additives. Effect of additive on the WRA reduction was more prominent with glutaraldehyde than with glyoxal. Reduction in WRA of cotton treated with both dialdehydes and boron compound was minimized by simultaneous addition of formic acid in the bath. Addition of formic acid was also generally beneficial in maintaining WI retentions after 8 months storage. Furthermore, boron compounds were also effective in improving retentions of mechanical properties. By FTIR analysis the residual aldehyde group was detected on the dialdehyde-finished cotton, whereas no peak was shown by addition of boron compounds. This suggested that the residual aldehyde group was a main cause of fabric yellowing on the dialdehyde-finished cotton. Dialhehyde with boron compound, therefore, can be used to replace a conventional formaldehyde-containing wrinkle resistant finishing of cotton.

• Journal of the Korean Applied Science and Technology
• /
• v.27 no.4
• /
• pp.531-538
• /
• 2010

The electrochemistry characterization of metal is important in many industrial applications. In this study, we investigated the C-V diagrams related to the electrochemistry characterization of nickel. We determined electrochemical measurement by using cyclic voltammetry with a three electrode system. A measuring range was reduced from initial potential to -1350mV, continuously oxidized to 1650mV and measured to the initial point. The scan rate were 100, 150, 200 and 200mV/s. As a result, the C-V characterization of nickel using ethanolamine and ethylethanolamine inhibitor appeared irreversible process caused by the oxidation current from the cyclic voltammogram. After adding ethanolamine compound additive, adsorption film constituted, and the passive phenomena happened. According to the results by cyclic voltammetry method, it was revealed that the effect of the electrochemistry characterization of nickel depends on ethanolamine structure interaction to adsorption complex.

• Tribology and Lubricants
• /
• v.10 no.4
• /
• pp.43-50
• /
• 1994

In order to elucidate the effects of co-existing additives (S$_{8}$, TBP: Tri butyl phosphate, ZnDTP: Zinc-dialkyl dithiophosphate) and the role of reacted surface film on the friction behavior of MoDTP (molybdenum dialkyl dithiophosphate), a friction experiment using a dual circular pipe edge surface type friction tester and XPS (X-ray photoelectronic spectrum) surface analysis were conducted. Friction reduction with MoDTP lubricant was proved to be greatly influenced by co-existing additive species. It was dependent on the properties of the film formed through the reaction between the additive and the surface. Phosphate film reduced the friction coefficient of MoDTP through suppression of diffusion of Mo compounds towards the metal substrate. On the other hand, sulfate film, which is inherently rich in lattice defects, did not lead to any appreciable friction reduction with MoDTP since the diffusion of the Mo compound towards the metal substrate was not effectively suppressed. With ZnDTP additive, the sulfide film formed through decomposition greatly influenced the lubricating performance of MoDTP. As such, properties of surface films formed from additives were proved to yield significant influence on the lubrication performance of MoDTP.