• Journal of Welding and Joining
• /
• 제18권5호
• /
• pp.105-111
• /
• 2000

The wear behavior of thermal sprayed AlSiMg-40TiC composite coatings were studied as a function of load and sliding velocity under unlubricated conditions. Experiments were performed using a block-on-ring(WC-6wt%/Co, Hv 1500) type. The tests were carried out a various load(30∼ 125.5N) and sliding velocity(0.5∼2.0m/s). Three wear rate regions were observed in the AlSiMg-40TiC composite coatings. The wear rate in region I at low load (less then 8N( were less than 1×{TEX}$10^{-5}${/TEX}㎣/m. Low wear rates in region I resulted from the load-bearing capacity of TiC particles. The transition from region I to II occurred when the applied load exceeded the fracture and pull-out strength of the particles. The TiC fractured particles trapped between the specimen and the counterface acted as third-body abrasive wear. The subsurface layer worn surface in region II was composed of the mechanically mixed layer (MML). The wear rate increase abruptly above a critical load (region III). The high wear rate in region III was induced by frictional temperature and involves massive surface damage.

• 한국가스학회지
• /
• 제15권1호
• /
• pp.35-39
• /
• 2011

본 논문에서는 FEV 차량용 복합소재 연료탱크의 탄소섬유 적층두께에 따라 달라지는 강도안전성에 미치는 기여율의 영향을 해석하고자 한다. 기여율에 의한 영향을 FEM 모델링으로 고찰하기 위해, 복합소재 연료탱크의 알루미늄 라이너와 탄소섬유 적층에 작용하는 von Mises 등가응력을 후프방향과 헤리컬방향에 대하여 각각 계산 하였다. FEM 해석결과에 따르면, 알루미늄 라이너에 작용하는 등가응력 기여율은 후프방향으로는 77.5%, $70^{\circ}C$ 경사진 헤리컬방향으로는 18.11%, $12^{\circ}C$ 경사진 헤리컬방향으로는 4.39%로 각각 작용하는 것으로 나타났다. $12^{\circ}C$ 경사진 탄소섬유의 적층 두께비가 후프방향 적층 두께비의 42% 정도로 높게 유지됨에도 불구하고 알루미늄 라이너 소재에서 보여준 기여율 경향은 탄소섬유 적층의 강도안전성에 대해서도 유사한 것으로 나타났다. 결과적으로, 탄소섬유 연료탱크의 강도안전성은 탄소섬유 적층의 두께보다 와인딩 각도에 의해 더 많은 영향을 받는다는 계산결과를 보여주고 있다.

• 항공우주기술
• /
• 제4권1호
• /
• pp.9-17
• /
• 2005

복합재 무힌지 로터시스템의 구조 감쇠 증대와 공탄성 안정성 향상에 대한 연구를 수행하였다. 무힌지 로터시스템의 구조 감쇠 증대를 위해 플렉셔에 구속 감쇠 처리 기법을 적용하였다. 점탄성 층과 구속 층이 부착된 플렉셔 구조물에 대한 모드해석은 MSC/NASTRAN을 이용하였고, 실험을 통해 구속 감쇠의 효과를 검증하였다. 구속 감쇠 처리된 복합재 플렉셔를 무힌지 로터시스템에 적용하여 제자리 비행 조건에서의 시험을 통해 in-plane 감쇠 증대를 고찰하였다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 추계학술발표대회 논문집
• /
• pp.121-124
• /
• 2004

The purpose of this study is to define the optimized layer pattern of composite wind turbine blade by using a commercial FEM program and to perform the fatigue test of T-Bolt. FEM analysis is done by using a PATRAN and ABAQUS to get a information about stress distribution ,critical deformation shape and get a critical load factor in local buckling analysis. As a result of the linear and nonlinear structural analysis, layer pattern of blade was optimized. T-Bolt is a connecting part of wind turbine blade and rotor hub, therefore T-bolt is cirtical part of wind turbine blade. T-bolt fatigue test is conducted to get a information of life cycle of T-bolt. The test is done by using a hydraulic actuator system

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 추계학술발표대회 논문집
• /
• pp.150-153
• /
• 2003

Longitudinal strains({$varepsilon}_x$) of the core and skin layers in glass fiber reinforced plastic(GFRP) cross-ply composite laminates have been studied using the embedded optical fiber sensor of totally-reflected extrinsic Fabry-Perot interferometer(TR-EFPI). Foil-type strain gauges bonded on both the upper and lower surfaces were used for the measurement of the surface strains. Both TR-EFPI sensor and strain gauge bonded on the specimen surface showed excellent agreement within -0.0086 ~ +0.0302% strain. It was shown that values of {$varepsilon}_x$ in the interior of the surface layer and the core layer measured by embedded TR-EFPI sensor was significantly higher than that of the specimen surface measured by strain gauges. The experimental results were ascertained with finite element analysis. Embedded TR-EFPI optical fiber sensor could measure accurately the internal strains which were different from the surface.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 추계학술발표대회 논문집
• /
• pp.211-214
• /
• 2005

This research studied robust design of composite structure under combined loading of bending and torsion. DOE (Design of Experiment) technique was used to find important design factors. The results show that the beam height, beam width, layer thickness and stack angle of outer-layer are important design parameter. The $2^{nd}$ DOE and RSM (Response Surface Model) were conducted to obtain optimum design. Multi-island genetic algorithm was used to optimum design. An approximate value of 6.65 mm in deflection was expected under optimum condition. Six sigma robust design was conducted to find out guideline for control range of design parameter. To acquire six sigma level reliability, the sigma level reliability, the standard deviation of design parameter should be controlled within 2.5 % of average design value.

• 한국소음진동공학회논문집
• /
• 제11권4호
• /
• pp.37-42
• /
• 2001

Active vibration control of laminated composite plates has been carried out to design structure with maximum possible damping capacity, using piezoceramic sensor/actuators and passive constrained-layer damping treatment. The equations of motion are derived for symmetrical, multi-layer laminated plates. The damping ratio(ζ) and modal damping(2ζ$\omega$) of the first bending and torsional modes are calculated by means of iterative complex eigensolution method for both passive and active vibration control. This paper addresses a design strategy of laminated composite plate under structural vibrations.

• Membrane and Water Treatment
• /
• 제4권2호
• /
• pp.83-93
• /
• 2013

In the present investigation, were synthesized composite membranes prepared by simultaneous casting of two polymer solutions using the technique of phase inversion by immersion / precipitation. The support layer was prepared using polyethersulfone and polysulfone as base polymer and for the top layer was used sulfonated polysulfone (SPSU) with 50% sulfonation degree. The morphology of the resulting membranes were characterized by scanning electron microscopy (SEM). The final results showed that it is possible to prepare composite membranes by simultaneous casting of two polymer solutions with adherence between the two layers. Regarding the permeation tests, the developed membranes presented values of hydraulic permeability within the range of commercial nanofiltration (NF) membranes. Values rejection of 80% ammonium ions can be increased by using a SPSU with a greater degree of sulfonation.

• 한국정밀공학회지
• /
• 제18권10호
• /
• pp.148-153
• /
• 2001

Active control of flexural vibrations of smart laminated composite beams has been carried out using piezoceramic sensor/actuator and viscoelastic material. The beams with passive constrained layer damping hale been analyzed by formulating the equations of motion through the use of extended Hamilton's principle. The dynamic characteristics such as damping ratio and modal damping of the beam are calculated for various fiber orientations by means of iterative complex eigensolution method. This paper addresses a design strategy of laminated composite under flexural vibrations to design structure with maximum possible damping capacity.

• 한국표면공학회지
• /
• 제25권2호
• /
• pp.73-81
• /
• 1992

The composite coating of suspended inert particles $\alpha$-Al2O3 and copper from acid sulphate bath was investigated at the Rotating Disk Electrode. Effects of rotation speeds of electrode, physical properties of electrolyte, the size and concentration of suspended particles on the codeposition ratio of Al2O3 and the enhancement of mass transfer of copper ions were examined. Particularly, new experimental method for the measurement of the codeposition ratio was suggested and also the characteristics of the composite coating layer were measured by Rutherford Backscattering Spectrometry. Mass transfer of suspended particles system were increased up to 40% more than those of without suspended particles system. Optimum conditions of current density, hydrodynamics of RDE, and particles concentration showing maximum codeposition ratio were appeared in our experimental ranges. It was shown that the suspended inert particles were codeposited mainly near the surface of the composite coating layer.