• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.1076-1079
• /
• 2001

An anolmalous magnetoresistance effect has been theoretically studied at very low temperatures for composite normal metal conductors. This anomalous behavior is due to transverse Hall currents in the composite which would result in increased losses and higher effective resistance for the composite conductor. In this paper, transverse current flow and effective resistance with Cu-Al conductor configuration were analyzed using FEM(finite element method) for predicting the Hall losses to be resulted in anomalous magnetoresistance effect. And they are plotted three dimensionally to be visualized.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 가을 학술발표회논문집(I)
• /
• pp.297-302
• /
• 2000

This paper presents the effect of diaphragm spacing ratio(depth to span) on behavior and capacity of composite steel-concrete structures of sandwich system. Numerical analysis has been performed variety diaphragm ratio, behavior and load condition. As a results of this study, in case of shear behavior and concentrated load, the capacity of structure such as yielding and ultimate load improve according to diaphragm ratio because of concrete confining effect by steel plate and stress redistribution by diaphragm. But in case of bending behavior or uniform load, it proved that diaphragm ratio don't influence on behavior and capacity of composite structures of sandwich system.

• 한국세라믹학회지
• /
• 제35권7호
• /
• pp.671-678
• /
• 1998

Hertzian indentation tests with sphere indenters were used to study the mechanical properties of glass-in-filtrated alumina and spinel composites and evaluated the effect of preform microstructure and evaluated the effect of preform microstructure and glass con-tents on contanct damage and strength. The spinel composite showed more brittle behavior than the alumina composite which is verified from indentation stress-strain curve cone cracks and quasi-plastic deformation developed at subsurface. Failure originated from either cone cracks(brittle mode) or deformation zone(quasi-plastic mode) above critical load for cracking(Pc) and yield ({{{{ {P }_{Y } }}) with the brittle mode more dominant in the spinels and the quasi-plastic mode more dominant in the aluminas. Even though brittle mode was dominant in the spinel composites the strength degradation from accumulation of damage above these critical loads was conspicuously small suggesting that the glass-infiltrated composites should be highly damage tolerant to the blunt contacts.

• 한국분말재료학회지
• /
• 제10권3호
• /
• pp.181-185
• /
• 2003

Resistance sintering under ultra-high pressure if developed to fabricate W-Cu composite containing 5 to 80v/o copper. The consolidation was carried out under pressure of 6 to 8 GPa and input power of 18 to 23 kW for 50 seconds. The densification effect and microstructure of these W-Cu composites are investigated. The effect of W particle size on ,sintering density was also studied. The micro hardness was measured to evaluate the sintering effect.

• International Journal of Aeronautical and Space Sciences
• /
• 제18권3호
• /
• pp.467-473
• /
• 2017

This paper focuses on the investigation of three-dimensional (3D) warping effect on the stiffness constants of composite beams with closed section profiles. A finite element (FE) cross-sectional analysis is developed based on the Reissner's multifield variational principle. The 3D in-plane and out-of-plane warping displacements, and sectional stresses are approximated as linear functions of generalized sectional stress resultants at the global level and as FE shape functions at the local sectional level. The classical elastic couplings are taken into account which include transverse shear and Poisson deformation effects. A generalized Timoshenko level $6{\times}6$ stiffness matrix is computed for closed section composite beams with and without warping. The effect of neglecting the 3D warping on stiffness constants is shown to be significant indicating large errors as high as 93.3%.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.167-170
• /
• 2005

This paper briefly reviews various existing methods to account for the effect of particle size on mechanical properties of particulate metal matrix composites. A simple and easy method is to use a size-dependent constitutive equation for the matrix. The suggested method does not require the development of a new computational algorithm and is compatible with any standard finite element software. Finite element analyses have been carried out to show how the deformation behavior of a metal matrix composite changes as the particle size and volume fraction are varied.

• 복합신소재구조학회 논문집
• /
• 제4권2호
• /
• pp.39-44
• /
• 2013

This study is aimed to examine the influence of the rotational stiffness of U-shaped ribs on the local buckling behaviors of laminated composite plates. Applying the orthotropic plates with eight layers of the layup $[(0^{\circ})4]s$ and $[(0^{\circ}/90^{\circ})2]s$, 3-dimensional finite element models for the U-rib stiffened plates were setup by using ABAQUS and then a series of eigenvalue analyses were conducted. There is a need to develope a simple design equation to establish the rotational stiffness effect, which could be easily quantified by comparing the theoretical critical stress equation for laminated composite plates with elastic restraints based on the Classical laminated plate theory. Through the parametric numerical studies, it is confirmed that there should clearly exist an increasing effect of local plate buckling strength due to the rotational stiffness by closed-section ribs. An applicable coefficient for practical design should be verified and proposed for future study. This study will contribute to the future study for establishing an increasing coefficient for the design strength and optimum design of U-rib stiffened plates.

• 한국재료학회지
• /
• 제8권11호
• /
• pp.993-998
• /
• 1998

본 연구는 형상기억합금을 이용하여 제조한 신소재 중의 하나인 형상기억복합재료를 소개하고자 한다. 이 복합재료는 TiNi 섬유의 형상기억효과로 금속복합재료의 취약점이라 할 수 있는 기지와 섬유간의 열팽창차이로 인한 인장잔류응력을 제거하고 기지내에 압축잔류응력을 발생시켜 높은 인장강도를 갖는다. 따라서 본 연구에서는 용탕단조법으로 복합재료를 제조한 후 미세조직을 관찰하고 TiNi 섬유의 역변태온도 이상에서 피로실험을 수행하여 복합재료의 피로특성을 검토하였다. 이 결과 363K에서의 피로균열전파제어효과는 섬유체적률과 예변형에 의하여 증가된다.

• Archives of Reconstructive Microsurgery
• /
• 제16권2호
• /
• pp.57-62
• /
• 2007

Non-vascularized free composite graft is one of the simple and effective reconstructive options, but its clinical use has been limited due to questionable survival rate. Early vascularization is essential for graft survival and is mainly carried out via recipient bed or repaired sites. This study was designed to investigate the effect of the lateral marginal approximations on the survival of the free composite flap using a model of skin-subcutaneous composite graft in rats. Thirty 1.5 ${\times}$ 1.5 $cm^2$ sized square shape composite flaps were elevated freely and reposed in place immediately on the dorsum of five Sprague-Dawley rats, and divided into five groups of six flaps. In all groups, graft bed was isolated with silastic sheet. In the group I, all sides of flap were repaired with blockage of silastic sheet insertion. Three, two, and one sides of flap were treated with same method in the group II, III, and IV respectively. Other sides of flaps were repaired without blockage, so all sides of flap were repaired in the group V. At 14 days later, the survived rate of each flap was evaluated according to the numbers of the repair sites. Histological examination was done for the evaluation of new vessel development quantitatively. Overall survived rates were increased with the number of repaired sites, but the group V only showed increased survival rate up to more than fifty percentile of the flap size with a significant difference statistically. New vessels were also increased in proportion with the number of repaired sites, and the repair site more than two had significant effect on the increased number of new vessels. In conclusion, at least more than three-fourth of flap circumference should be repaired in order to increase flap survival effectively under the condition of bed isolation.

• Restorative Dentistry and Endodontics
• /
• 제26권5호
• /
• pp.399-408
• /
• 2001

Tooth bleaching has been prevailing recently for its ability to recover the color and shape of natural teeth without reduction of tooth material. However, it has been reported that bleaching procedure adversely affects the adhesive bond strength of composite resin to tooth. At the same time the bond strength was reported to be regained by application of some chemical agents. The purpose of this in vitro study was to investigate the effect of the removal of residual peroxide on the composite- enamel adhesion and also evaluated fracture mode between resin and enamel after bleaching. Sixty extracted human anterior and premolars teeth were divided into 5 groups and bleached by combined technique using of office bleaching with 35 % hydrogen peroxide and matrix bleaching with 10% carbamide peroxide for 4 weeks. After bleaching, the labial surfaces of each tooth were treated with catalase, 70% ethyl alcohol, distilled water and filled with composite resin. Shear bond strength was tested and the fractured surfaces were also examined with SEM. Analysis revealed significantly higher bond strength values. (p＜0.05) for catalase-treated specimens, but water-treated specimens showed reduction of bond strength, alcohol- treated specimens had medium value between the two groups(p＜0.05). The fracture mode was shown that the catalase group and the alcohol group had cohesive failure but the water sprayed group had adhesive failure. It was concluded that the peroxide residues in tooth after bleaching seems to be removed by gradual diffusion and the free radical oxygen from peroxide prevents polymerization by combining catalyst in the resin monomer. Therefore it may be possible to eliminate the adverse effect on the adhesion of composite resin to enamel after bleaching by using water displacement solution or dentin bonding agent including it for effective removal of residual peroxide.