• Journal of Electrical Engineering and Technology
• /
• v.9 no.5
• /
• pp.1511-1519
• /
• 2014

The objective of this paper is to propose a modelling of a small compressed air energy storage system, which drives an induction generator based on a field-oriented control (FOC) principle for a renewable power generation. The proposed system is a hybrid technology of energy storage and electrification, which is developed to use as a small scale of renewable energy power plant. The energy will be transferred from the renewable energy resource to the compressed air energy by reciprocating air compressor to be stored in a pressurized vessel. The energy storage system uses a small compressed air energy storage system, developed as a small unit and installed above ground to avoid site limitation as same as the conventional CAES does. Therefore, it is suitable to be placed at any location. The system is operated in low pressure not more than 15 bar, so, it easy to available component in country and inexpensive. The power generation uses a variable speed induction generator (IG). The relationship of pressure and air flow of the compressed air, which varies continuously during the discharge of compressed air to drive the generator, is considered as a control command. As a result, the generator generates power in wide speed range. Unlike the conventional CAES that used gas turbine, this system does not have any combustion units. Thus, the system does not burn fuel and exhaust pollution. This paper expresses the modelling, thermodynamic analysis simulation and experiment to obtain the characteristic and performance of a new concept of a small compressed air energy storage power plant, which can be helpful in system designing of renewable energy electrification. The system was tested under a range of expansion pressure ratios in order to determine its characteristics and performance. The efficiency of expansion air of 49.34% is calculated, while the efficiency of generator of 60.85% is examined. The overall efficiency of system of approximately 30% is also investigated.

• International Journal of Computer Science & Network Security
• /
• v.22 no.1
• /
• pp.69-76
• /
• 2022

At the current stage of globalization and European integration of Ukraine, the aspects related to the effective fight against corruption in the system of economic security of our country are receiving more and more attention, as they become a prerequisite for continuing reforms based on international funding. In order to consider this issue and solve this problem, the necessary step is to develop and implement real mechanisms of the system for detecting and preventing corrupt behavior, which are based on international anti-corruption standards. The leading component of this system is the management of corruption risks in the system of economic security in order to identify them and implement measures to reduce them. This study analyzes the corruption perception index in Ukraine in recent years, which showed a positive, albeit somewhat slow dynamics of its growth, indicating a gradual increase in overcoming corruption through the introduction of a number of anti-corruption measures and changes. It is proved that the current stage of socio-economic development of the country contributes to strengthening the processes of combating corruption and preventing corruption risks, creating an effective and efficient anti-corruption system of the state. The concept of "corruption" was studied, it was found that in the field of public administration it is considered from different positions and is closely related to the concept of "corruption risks". The essence and features of corruption risks are studied, the preconditions of their occurrence are formulated, the relationship between the causes of corruption risks and economic security in the field of public authority has been established. The system of corruption risk management is considered and its components are characterized. It is proposed to increase the effectiveness of anticorruption policy through the implementation of measures aimed at investigating the causes of corruption risks, as well as developed effective and effective means of reducing corruption risks within the system of economic security

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.413-416
• /
• 1998

Sensitivity and calibration considerations are most important in the design and implementation of real control systems. Ideally parameter changes due to various causes should not appreciably affect the system's performances. But all the values of physical components of the plants and controllers as well as the relevant environmental conditions change in time, thus the output performance can be deteriorated during the operating span of the system. Naturally the duty of calibration or the prevention of performance deterioration due to excessive component sensitivity should be provided to the control system. In this paper, we propose a digital controller which has the capability of calibration and gain adjustment as well as the execution of control law. Specifically the problems of gain adjustment and offset calibration in the light source and CdS sensor module for position measurement in a flexible link system are considerably resolved. The parameters of measurement module are prone to change due to environmental brightness conditions resulting in poor steady state performance of the overall control system. Thus a proper method is necessary to provide correction to the changed values of gain and offset in the position measurement module. The proposed controller, whenever necessary, measures the open-loop characteristics, andthen calculates the offset and sensor gain correction values based on the prepared standard measurements. It is applied to the control of a flexible link system with the gain and offset calibration porblems in the light sensor module for position to show the applicability.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.04a
• /
• pp.99-102
• /
• 1997

An electronic nose system is an instrument designed far mimicking human olfactory system. It consists generally of gas (odor) sensor array corresponding to olfactory receptors of human nose and artificial neural network pattern recognition technique based on human biological odor sensing mechanism. Considerable attempts to develop the electronic nose system have been made far applications in the fields of floods, drinks, cosmetics, environment monitoring, etc. A portable electronic nose system has been fabricated by using oxide semiconductor gas sensor array and pattern recognition technique such as principal component analysis (PCA) and back propagation artificial neural network The sensor array consists of six thick film gas sensors whose sensing layers are Pd-doped WO$_3$ Pt-doped SnO$_2$ TiO$_2$-Sb$_2$O$_3$-Pd-doped SnO$_2$ TiO$_2$-Sb$_2$O$_{5}$-Pd-doped SnO$_2$+Pd filter layer, A1$_2$O$_3$-doped ZnO and PdCl$_2$-doped SnO$_2$. As an application the system has been used to identify CO/HC car exhausting gases and the identification has been successfully demonstrated.d.

• Proceedings of the KIEE Conference
• /
• 2001.07e
• /
• pp.80-85
• /
• 2001

Frequency is an important operating parameter of a power system. Frequency of a power system remains constant if sum of all the loads plus losses equals total generation in the system. However, the frequency starts to decrease if total generation is less than the sum of loads and tosses. On the other hand, the system frequency increases if total generation exceeds the sum of loads and losses. Electric power systems sustain transient frequency swings whenever the balance between generation and load does not no longer hold. To cope with this Constraints, it requires an accurate and high speedy frequency deviation estimation technique and suitable adjustment to obtain the power system energy balance. The fundamental frequency component of 3-phase signal is first extracted by using an algorithm based on FIR(finite duration impulse response) filter, a phase angle of a voltage. The rate change of the phase angle is used for estimation and speed in its process. Also, to confirm the validity of the proposed algorithm, the simulation results obtained by using EMTP(electro magnetic transients program) are shown.

• Journal of the Institute of Convergence Signal Processing
• /
• v.5 no.1
• /
• pp.25-31
• /
• 2004

This paper is research about the improvement of recognition rate of the biometrics user identification system using the data previously stored in the non contact Ic smart card. The proposed system identifies the user by analyzing the iris pattern his or her us. First, after extracting the area of the iris from the image of the iris of an eye which is taken by CCD camera, and then we save PCA Coefficient using GHA(Generalized Hebbian Algorithm) into the Smart Card. When we confirmed the users, we compared the imformation of the biometrics of users with that of smart card. In case two kinds of information was the same, we classified the data by using SVM(Support Vector Machine). The Experimental result showed that this system outperformed the previous developed system.

• International Journal of Internet, Broadcasting and Communication
• /
• v.13 no.3
• /
• pp.169-177
• /
• 2021

Recently, the use of electric and electronic control systems is increasing in the automobile industry. This increase in the electric and electronic control system greatly increases the complexity of designing a vehicle, which leads to an increase in the malfunction of the system, and a safety problem due to the malfunction is becoming an issue. Based on IEC 61508 relating to the functional safety of electrical/electronic/programmable electronics, the ISO 26262 standard specific to the automotive sector was first established in 2011, and a revision was published in 2018. Malfunctions due to system failure are covered by ISO 26262, but ISO/PAS 21448 is proposed to deal with unintended malfunctions caused by changes in the surrounding environment. ISO 26262 sets out safety-related requirements for the entire life cycle. Functional safety analysis includes FTA (Fault Tree Analysis), FMEA (Failure Mode and Effect Analysis), and HAZOP (Hazard and Operability). These analysis have limitations in dealing with failures or errors caused by complex interrelationships because it is assumed that a failure or error affecting the risk occurs by a specific component. In order to overcome this limitation, it is necessary to apply the STPA (System Theoretic Process Analysis) technique.

• Nuclear Engineering and Technology
• /
• v.55 no.10
• /
• pp.3898-3906
• /
• 2023

The paper notes that the most common way of handling spent nuclear fuel (SNF) of power reactors is its temporary long-term dry storage. At the same time, the operation of the dry spent fuel storage facilities almost never use the modern capabilities of information systems in safety control and collecting information for the next studies under implementation of aging management programs. The author proposes a structure of an information system that can be implemented in a dry spent fuel storage facility with ventilated storage containers. To control the thermal component of spent fuel storage safety, a database structure has been developed, which contains 5 tables. An algorithm for monitoring the thermal state of spent fuel was created for the proposed information system, which is based on the comparison of measured and forecast values of the safety criterion, in which the level of heating the ventilation air temperature was chosen. Predictive values of the safety criterion are obtained on the basis of previously published studies. The proposed algorithm is an implementation of the information function of the system. The proposed information system can be used for effective thermal monitoring and collecting information for the next studies under the implementation of aging management programs for spent fuel storage equipment, permanent control of spent fuel storage safety, staff training, etc.

• Journal of Drive and Control
• /
• v.21 no.3
• /
• pp.9-19
• /
• 2024

Many modern hydraulic excavators now use EPPRVs (Electronic Proportional Pressure Reducing Valves) in their pilot systems to control the spool displacement of the main hydraulic system. However, the performance of these systems is often limited by factors such as magnetic hysteresis, mechanical wear, and transient responses influenced by operating conditions and component installation. This paper presents a pressure feedback controller for excavator pilot systems that utilize EPPRVs. This controller significantly reduces steady-state pressure control errors and mitigates the hysteresis effects commonly seen in traditional open-loop systems. To achieve this, we integrated EPPRVs with the main hydraulic valve and injected a chirp signal into the solenoid current. By doing so, we were able to measure the frequency response of the pilot system across different operating pressures and estimate the system dynamics model. Using these models, we designed a set of PI pressure feedback controllers that are guaranteed to be stable. These controllers were then integrated with a gain scheduler based on a lookup table. Experimental results demonstrate that when the developed pressure feedback controller is incorporated into the conventional open-loop controller, it effectively reduces steady-state pressure control errors and mitigates hysteresis.

• Journal of Veterinary Clinics
• /
• v.33 no.5
• /
• pp.278-285
• /
• 2016

Epidemiological studies have shown the association between transportation of live animals and the potential transmission of infectious disease between premises. This finding was also observed in the 2014-2015 foot-and-mouth disease (FMD) outbreak in Korea. Furthermore, slaughterhouses played a key role in the global spread of the FMD virus during the epidemic. In this context, in-depth knowledge of the structure of direct and indirect contact between slaughterhouses is paramount for understanding the dynamics of FMD transmission. But the social network structure of vehicle movements to slaughterhouses in Korea remains unclear. Hence, the aim of this study was to configure a social network topology of vehicle movements between slaughterhouses for a better understanding of how they are potentially connected, and to explore whether FMD outbreaks can be explained by the network properties constructed in the study. We created five monthly directed networks based on the frequency and chronology of on- and off-slaughterhouse vehicle movements. For the monthly network, a node represented a slaughterhouse, and an edge (or link) denoted vehicle movement between two slaughterhouses. Movement data were retrieved from the national Korean Animal Health Integrated System (KAHIS) database, which tracks the routes of individual vehicle movements using a global positioning system (GPS). Electronic registration of livestock movements has been a mandatory requirement since 2013 to ensure traceability of such movements. For each of the five studied networks, the network structures were characterized by small-world properties, with a short mean distance, a high clustering coefficient, and a short diameter. In addition, a strongly connected component was observed in each of the created networks, and this giant component included 94.4% to 100% of all network nodes. The characteristic hub-and-spoke type of structure was not identified. Such a structural vulnerability in the network suggests that once an infectious disease (such as FMD) is introduced in a random slaughterhouse within the cohesive component, it can spread to every other slaughterhouse in the component. From an epidemiological perspective, for disease management, empirically derived small-world networks could inform decision-makers on the higher potential for a large FMD epidemic within the livestock industry, and could provide insights into the rapid-transmission dynamics of the disease across long distances, despite a standstill of animal movements during the epidemic, given a single incursion of infection in any slaughterhouse in the country.