• Carbon letters
• /
• 제10권2호
• /
• pp.101-108
• /
• 2009

Various silanes, amino silane, vinyl silane, TESPD, and ZS (TESPD/zinc soap complex), are added into chlorinated isobutylene-isoprene copolymer (CIIR)/hard clay/carbon black (CB) compound and they are investigated with respect to the vulcanization characteristics, the processability, and the mechanical properties. In hard clay/CB filled system, only ZS silane added compound shows both lower Mooney viscosity and extrusion torque while vinyl silane added compound showed only a lower extrusion torque. All the ZS added compounds showed the lowest viscosity among them. The silane added compounds showed an increased modulus. In 'fatigue to failure' count test, the ZS added compound showed superior counts compared to other silane (amino, vinyl, TESPD) added compounds. The mechanical properties were significantly increased when the S2 and ZS were added into CIIR/hard clay/CB compound. The ZS added compounds showed a significant improvement on elongation modulus.

• 한국표면공학회지
• /
• 제39권6호
• /
• pp.282-287
• /
• 2006

Viscosities of $LaCl_3-NaCl$ binary melts were measured by the capillary method over the range of their liquidus temperatures to about 1200K. The cell constant were determined by using pure water. The results obtained are summerized as follows: Viscosities were decreased with the content of NaCl for all over the composition range of binary melts. Composition - viscosity relation for the binary melts show a non-linear from the additivity line and the deviations shows a maximum at about 60 mol% NaCl. This suggests the existence of the complex ion of $LaCl_4^-$ in the melt. Activation energy for viscous flow of the binary melts decrease monotonously with the increasing content of NaCl.

• 한국식품영양과학회지
• /
• 제29권5호
• /
• pp.860-864
• /
• 2000

The steady and dynamic shear rheological properties of traditional kochujang fermented at three different temperatures (20${^circ}C$, 25${^circ}C$ and 30${^circ}C$) were studied. Flow of kochujang samples showed time dependence, which was quantitatively described by the Weltman model, Kochujang samples were highly shear thinning fluids (n=0.25~0.27) with large magnitudes of Casson yield stresses (1.09~1.21 kPa). Consistency index (K) and apparent viscosity (${\eta}_{a,20}$) increased with increase in fermentation temperature of kochujang. Storage (G') and loss (G") moduli increased with increase in frequency (ω), while complex viscosity (${\eta}^{\ast}$) decreased. Based on dynamic shear data, kochujang samples exhibit structural properties similar to weak gels. The complex and steady shear viscosities at different fermentation temperatures followed the Cox-Merz superposition rule with the application of the shift factor (a=0.011~0.016).

• Bulletin of the Korean Chemical Society
• /
• 제16권11호
• /
• pp.1046-1056
• /
• 1995

A topological theory has been introduced to evaluate the degree of complexation and the viscosity of polymer complexes by extending the theory of Iliopoulos and Audebert for aqueous polymer solutions. The previous theory of Iliopoulos and Audebert has offered only a semiquantitative theoretical model for polymer complex systems, whereas our present work gives a general theoretical model applicable to all the polymer complex systems. Their theories considered only the physical property term caused by the displacement of complexed points between polymer solute chains, while our theory deals with all the physical effects, caused by the displacement of complexed points entangled points in polymer solute chains. There have been predicted the characteristics of physical properties from the expression. It is exposed that the predictive values show good agreement with the experimental data for polymer complexes.

• Bulletin of the Korean Chemical Society
• /
• 제20권11호
• /
• pp.1329-1334
• /
• 1999

The curing characteristics of diglycidyl ether of bisphenol A (DGEBA) with diaminodiphenylmethane (DDM) as a curing agent were studied using differential scanning calorimetry (DSC), rheometrics mechanical spectrometry (RMS), and dielectric analysis (DEA). The isothermal curing kinetics measured by DSC were well represented with the generalized auto-catalytic reaction model. With the temperature sweep, the inverse relationship between complex viscosity measured by RMS and ionic conductivity obtained from DEA was established indicating that the mobility of free ions represented by the ionic conductivity in DEA measurement and the chain segment motion as revealed by the complex viscosity measured from RMS are equivalent. From isothermal curing measurements at several different temperatures, the ionic conductivity contribution was shown to be dominant in the dielectric loss factor at the early stage of cure. The contribution of the dipole relaxation in dielectric loss factor became larger as the curing further proceeded. The critical degrees of cure, at which the dipolar contribution in the dielectric loss factor starts to appear, increases as isothermal curing temperature is increased. The dielectric relaxation time at the same degree of cure was shorter for a sample cured at higher curing temperature.

• Restorative Dentistry and Endodontics
• /
• 제29권6호
• /
• pp.520-531
• /
• 2004

The aim of this study was to investigate the effect of monomer and filler compositions on the rheological properties related to the handling characteristics of resin composites. Methods. Resin matrices that Bis-GMA as base monomer was blended with TEGDMA as diluent at various ratio were mixed with the Barium glass (0.7 um and 1.0 um), 0.04 um fumed silica and 0.5 um round silica. All used fillers were silane treated. In order to vary the viscosity of experimental composites, the type and content of incorporated fillers were changed, Using a rheometer, a steady shear test and a dynamic oscillatory shear test were used to evaluate the viscosity ($\eta$) of resin matrix, and the storage shear modulus (G'), the loss shear modulus (G"), the loss tangent ($tan{\delta}$) and the complex viscosity (${\eta}^*$) ofthe composites as a function of frequency ${\omega}{\;}={\;}0.1-100{\;}rad/s$. To investigate the effect of temperature on the viscosity of composites, a temperature sweep test was also undertaken. Results. Resin matrices were Newtonian fluid regardless of diluent concentration and all experimental composites exhibited pseudoplastic behavior with increasing shear rate. The viscosity of composites was exponentially increased with increasing filler volume%. In the same filler volume, the smaller the fillers were used, the higher the viscosities were. The effect of filler size on the viscosity was increased with increasing filler content. Increasing filler content reduced $tan{\delta}$ by increasing the G' further than the G". The viscosity of composites was decreased exponentially with increasing temperature.

• 유변학
• /
• 제10권4호
• /
• pp.234-246
• /
• 1998

본 연구의 목적은 고분자 농후용액의 정상유동특성(비선형 거동)과 소진폭 전단변형하에서의 동적 점탄성(선형 거동) 간에 존재하는 상관관계를 파악함에 있다. 이를 위해 Advanced Rheometric Expansion System(ARES)과 Rheometrics Fluids Spectrometer (RFS II)를 사용하여 폴리에틸렌 옥사이드, 폴리이소부틸렌 및 폴리아크릴 아마이드 농후용액의 정상류점도 및 동적 선형 점탄성을 광범위한 전단속도와 각주파수 영역에서 측정하였다. 이들 측정결과로부터 정상류점도와 동적점도 또는 동적 유동성간의 상관관계를 제시한 몇 가지 관계식의 적용성을 비교.검토하였다. 그리고 정상류점도와 복소점도의 절대치를 비교하여 양자간의 등가관계를 나타내는 Cox-Merz 법칙의 적용성에 대한 농도의 영향을 실험적으로 검증하였다. 나아가서 대변형하에서의 비선형성의 정도를 나타내는 비선형 스트레인 척도의 개념을 도입하여 Cox-Merz 법칙의 적용성에 미치는 영향을 이론적 관점에서 고찰하였다. 이상의 연구를 통해 얻어진 결과를 요약하면 다음과 같다. (1) 정상류점도의 전단속도 의존성과 동적 점탄성의 각주파수 의존성간에 제시된 여러 관계식들 중에서 정상류점도와 복소점도 절대치간의 등가관계를 나타내는 Cox-Merz법칙이 가장 우수한 적용성을 갖는다. (2) 높은 전단속도 또는 각주파수 영역에서는 정상류점도와 복소점도의 관계가 용액 농도에 따라 서로 상이하게 나타난다. 즉 낮은 농도의 용액에서는 정상류점도가 복소점도에 비해 다소 큰 값을 나타내며, 농도가 증가할수록 이러한 경향은 역전되어 높은 농도의 용액에서는 복소점도가 정상류점도에 비해 큰 값을 갖는다. (3) 비선형 스트레인 척도는 작은 크기의 변형량에서는 직선적으로 증가하다가 점차적으로 그 증가율이 감소하여 최대치에 도달한 후 그 이상의 변형량 영역에서는 변형량이 증가함에 따라 점차 감소하는 거동을 나타낸다. 이러한 거동은 스트레인 증가에 따라 진폭이 점차로 감소하는 감쇠진동함수의 형태를 갖는 이론적 예측과는 상당한 차이를 나타낸다. (4) 대변형하에서 비선형 스트레인 척도의 기울기 (고분자 용액의 비선형성의 정도)는 Cox-Merz 법칙의 적용성에 영향을 미치며, 이 값이 감소할수록 Cox-Merz 법칙은 더욱 잘 성립한다.

• Tribology and Lubricants
• /
• 제15권4호
• /
• pp.343-353
• /
• 1999

The role of viscosity index improver's(Ⅶ) additives for modem engine lubrication is complex. Under the condition of atmosphere or low shear rate, the characteristics of Ⅶ added lubricant is verified and quoted frequently for mathematical model of lubricant behavior. However, recent research shows that added lubricant has the characteristics of shear thinning at high shear rate condition although it performs well enough over the whole range of working temperature. At high shear rate, they show significant decrease of apparent viscosity irrespective of temperature. Many experimental researches verify that Ⅶ added lubricant shows boundary film layer formation on the solid surface as well as shear thinning effect by its polymeric molecular characteristics. The intend of our research is to verify the effects of Ⅶ from the viewpoint of continuum mechanics, because conventional Reynolds'equation with only pressure-viscosity relation cannot fully predict the lubricant behavior under the Ⅶ added condition. In these aspects, Reynolds'equation of Newtonian fluid model lacks the reflection of real fluid behavior and there is no way to explain the non-linear characteristics of Ⅶ added lubricant. In this research, we mathematically modeled the Ⅶ added lubricant behaviors which are the characteristics of non-Newtonian fluid behavior at high shear rate and boundary film formation on the solid surface. The consideration of elastic deformation in the contact region is also included in our computation and finally the converged film pressure and the film thickness with elastic deformation are obtained. The results are compared with those of Newtonian fluid model.

• Nuclear Engineering and Technology
• /
• 제54권11호
• /
• pp.4322-4328
• /
• 2022

The two-fluid model is widely used to describe two-phase flows in complex systems such as nuclear reactors. Although the two-phase flow was successfully simulated, the standard two-fluid model suffers from an ill-posed nature. There are several remedies for the ill-posedness of the one-dimensional (1D) two-fluid model; among those, artificial viscosity is the focus of this study. Some previous works added artificial diffusion terms to both mass and momentum equations to render the two-fluid model well-posed and demonstrated that this method provided a numerically converging model. However, they did not consider mass conservation, which is crucial for analyzing a closed reactor system. In fact, the total mass is not conserved in the previous models. This study improves the artificial viscosity model such that the 1D incompressible two-fluid model is well-posed, and the total mass is conserved. The water faucet and Kelvin-Helmholtz instability flows were simulated to test the effect of the proposed artificial viscosity model. The results indicate that the proposed artificial viscosity model effectively remedies the ill-posedness of the two-fluid model while maintaining a negligible total mass error.

• 폴리머
• /
• 제34권5호
• /
• pp.485-489
• /
• 2010

본 연구에서는 폴리락트산(PLA)의 용융강도를 높이기 위하여 PLA에 글리시딜 메타크릴레이트(GMA)를 PLA에 첨가한 후 전자선을 조사하여 PLA를 개질하였다. GMA는 5 phr(parts per hundred parts of resin)로 고정하고 전자선 조사량을 변화시키며 개질 PLA을 제조하였으며, 이후 열적, 유변학적 특성 및 젤화도를 조사하였다. 주파수 0.1 rad/s에서 조사량 300 kGy로 개질된 PLA와 순수 PLA의 유변학적 물성을 서로 비교해보면 복합점도는 약 210배, 탄성률은 약 14500배 상승하는 예외적으로 아주 큰 변화를 보였다. 젤화도의 결과로 조사량 200 kGy 이하로 조사된 시료에서 일어난 분자반응은 가교화 반응보다는 가지화 반응이 우세하다는 것을 알 수 있었다.