• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.35 no.4
• /
• pp.24-32
• /
• 2012

Of many approaches to reduce motion analysis errors, the compensation method of anatomical landmarks estimates the position of anatomical landmarks during motion. The method models the position of anatomical landmarks with joint angle or skin marker displacement using the data of the so-called dynamic calibration in which anatomical landmark positions are calibrated in ad hoc motions. Then the anatomical landmark positions are calibrated in target motions using the model. This study applies the compensation methods with joint angle and skin marker displacement to three lower extremity motions (walking, sit-to-stand/stand-to-sit, and step up/down) in ten healthy males and compares their performance. To compare the performance of the methods, two sets of kinematic variables were calculated using different two marker clusters, and the difference was obtained. Results showed that the compensation method with skin marker displacement had less differences by 30~60% compared to without compensation. And, it had significantly less difference in some kinematic variables (7 of 18) by 25~40% compared to the compensation method with joint angle. This study supports that compensation with skin marker displacement reduced the motion analysis STA errors more reliably than with joint angle in lower extremity motion analysis.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.76-79
• /
• 2007

Optical compensation films are widely used to enlarge viewing angle characteristics for LCDs. A new surface film with an inner light scattering layer was newly developed to improve gray scale inversion. This paper describes technologies regarding these films that enhance the viewing angle characteristics for LCDs.

• International Journal of Aeronautical and Space Sciences
• /
• v.14 no.4
• /
• pp.379-386
• /
• 2013

The hemispherical resonator gyroscope is a type of vibratory gyroscope, which can measure angle or angular rate, based on its operating mode. This paper deals with the case when the hemispherical resonator gyroscope is operated in angle measurement mode. In angle measurement mode, the resonator pattern angle precesses, with respect to the external rotation input, by the principle of the Coriolis effect, so that the external rotation can be estimated, by measuring the amount of precession angle. However, this pattern angle drifts, due to the manufacturing error of the resonator. Since the drift effect causes degradation of the angle estimation performance of the resonator, the corresponding drift compensation control should be performed, to enhance the estimation performance. In this paper, a mathematical model of the hemispherical resonator gyro is first introduced. By using the mathematical model, a nonlinear observer for imperfection parameter estimation, and the corresponding compensation controller are designed to operate hemispherical resonator gyros, as angle measurement sensors.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.426-429
• /
• 2005

In this study, the formed tool is used to machine of bearing raceway and a shape compensation scheme is proposed to compensate for shape of it in turning process. It is introduced the conventional design method of the formed tool; a simple depth compensation method and a drawing compensation method. And it is performed to investigate in detail properties of the formed tool about a tool angle and problems of a turning process of bearing raceway using the formed tool. The applicability of the proposed scheme is examined by comparing the experimental results obtained by a new designed formed tool with those obtained by a conventional tool.

• Transactions of Materials Processing
• /
• v.29 no.4
• /
• pp.188-193
• /
• 2020

Piping work of large ships or offshore plants is often done in a narrow and confined space, requiring precise bending and safety. In order to realize an accurate bending angle, it is very important to predict and correct a deformation that may be caused by elasticity in the bending process, that is, an angular deviation due to springback. Therefore, by using CAE analysis to develop a correction angle model for springback based on multiple tube bending angles and using trend line data derived from this correction angle model, at bending the tube as the diameter of the base former and the tube outer diameter change, the springback compensation angle at any angle can be obtained. In this study, the bending mechanism was analyzed to increase the bending precision, and a correction angle model was developed and a trend line was derived in consideration of springback occurring in the bending process. In order to derive a more accurate and reliable trend line, a tube tensile test was performed, and the reliability of the corrected angle trend line was verified by comparing the bending angle measurement and analysis results with a 3D scanner.

• Journal of Power Electronics
• /
• v.19 no.6
• /
• pp.1380-1392
• /
• 2019

Input filters are very important to matrix converters (MCs). They are used to improve grid side current waveform quality and to reduce the input voltage distortion supplied to the grid side. Due to the effects of the input filter and the output power, the grid side power factor (PF) is not at unity when the input power factor angle is zero. In this paper, the displacement angle between the grid side phase current and the phase voltage affected by the input filter parameters and output power is analyzed. Based on this, a new grid side PF unity compensation method implemented in the indirect space vector pulse width modulation (ISVPWM) method is presented, which has a larger compensation angle than the traditional compensation method, showing a higher grid side PF at unity in a wide output power range. Simulation and experimental results verify that the analysis of the displacement angle between the grid side phase current and the phase voltage affected by the input filter and output power is right and that the proposed compensation method has a better grid side PF at unity.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.5
• /
• pp.999-1004
• /
• 2012

In this paper, camera modules and lens's images were analyzed for the compensation of distortion image by wide angle lens based WDR(Wide Dynamic Range) with high resolution sensor(2-Mega CMOS Image sensor). Due to wide angle ($176^{\circ}$) of designed wide angle camera modules, the compensation result of distorted image was analyzed, and the application of these modules was proposed for smart NUX(Natural User eXprience).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.3
• /
• pp.175-180
• /
• 2016

In this study, we proposed an optical compensation method to improve the symmetricity of contrast ratio for wide viewing angle IPS (in-plane switching) LCD. First, the phase retardation depending on the thickness of compensation film is calculated, and then the phase change is presented at the $Poincar{\acute{e}}$ sphere. The phase retardation and the polarization state of the light passing through the optical elements are caculated by using the EJMM (extended Jones matrix method). In addition, the transmittance and the contrast countour are also calculated by using the Berremann's $4{\times}4$ matrix method. The simulation is carried out for a IPS LC cell with positive A/C/A compensation film. From the standard deviation of the contrast ratio, we confirmed the symmetricity at each viewing angle is inversely proportional to the standard deviation and calculated the optimum design condition of the uniaxial compensation film for the IPS LCD.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.12
• /
• pp.1101-1104
• /
• 2008

We have studied electro-optic characteristics to improve viewing angle of the in-plain switching (IPS) liquid crystal display using an compensation film. The IPS mode shows relatively large light leakage and color shift in diagonal directions in a dark state. To solve this problem, we have compensated the low contrast ratio in diagonal directions using one optimized discotic film and adjusting TAC films of polarizers. The compensated IPS mode shows wide viewing angle characteristics that region of CR 50:1 is over $60^{\circ}$ of polar angle in all directions. The optimized IPS cell exhibits much better performances than other methods do in terms of CR and color uniformity.

• Journal of Power Electronics
• /
• v.14 no.6
• /
• pp.1254-1262
• /
• 2014

Magneto-electric encoders have been widely used in industry and military applications because of their good shock resistance, small volume, and convenient data processing. However, the characteristics of a magneto-electric encoder's signal generator and hall sensor changes minimally with temperature variation. These changes cause an angle drift. The main purpose of this study is to construct the compensation system of a neural network and constantly update weight coefficients of temperature correction by finite iteration calculation so that the angle value modified can approach the angle value at the target temperature. This approach is used in adaptive correction of the angle value.