• Journal of the Korean Society of Clothing and Textiles
• /
• v.30 no.12 s.159
• /
• pp.1730-1736
• /
• 2006

To utilize hanji for fashion accessory efficiently, dyeability of Hanji should be improved. Though Hanji mostly consists of cellulose such as cotton and ramie, also has various impurities, and has the different internal and surface structure from textile materials. Because of them, Hanji might show different dyeing behavior. As physical properties of Hanji are reduced in wet condition, dyeing process would damage the physical properties of Hanji Therefore, in this study, dyeing properties of Hanji using direct dye were examined in comparison with cotton and ramie. Effect of dyeing on tensile strength, and bleeding of direct dye by water from Hanji, colorfastness to light were also estimated. While Hanji showed the maximun dye exhaustion at $25^{\circ}C$, cotton and ramie showed those at $60^{\circ}C$. Tensile strength of Hanji reduced after Hanji was dyed. When Hanji was dyed at $25^{\circ}C$, the more bleeding occurred than at higher dyeing temperature. Hanji which had higher K/S values were bled more than those had lower K/S value. Colorfastness to light of Hanji dyed with direct dye was not inferior to those of cotton and ramie.

• Archives of Pharmacal Research
• /
• v.26 no.3
• /
• pp.214-223
• /
• 2003

The present study was conducted to investigate the effects of green tea extract (GTE) on arterial blood pressure and contractile responses of isolated aortic strips of the normotensive rats and to establish the mechanism of action. The phenylephrine ($10^{-6}~10^{-5}M$)-induced contractile responses were greatly inhibited in the presence of GTE (0.3~1.2 mg/mL) in a dose-dependent fashion. Also, high potassium ($3.5{\times}10^{-2}~5.6{\times}10^{-2}{\;}M$)-induced contractile responses were depressed in the presence of 0.6~1.2 mg/mL of GTE, but not affected in low concentration of GTE (0.3 mg/mL). However, epigallocatechin gallate (EGCG, $4~12{\;}{\mu}g/mL$) did not affect the contractile responses evoked by phenylephrine and high $K^+$. GTE (5~20 mg/kg) given into a femoral vein of the normotensive rat produced a dose-dependent depressor response, which is transient. Interestingly, the infusion of a moderate dose of GTE (10 mg/kg/30 min) made a significant reduction in pressor responses induced by intravenous norepinephrine. However, EGCG (1 mg/kg/30 min) did not affect them. Collectively, these results obtained from the present study demonstrate that intravenous GTE causes a dose-dependent depressor action in the anesthetized rat at least partly through the blockade of adrenergic $\alpha_1$-receptors. GTE also causes the relaxation in the isolated aortic strips of the rat via the blockade of adrenergic $\alpha_1$-receptors, in addition to the unknown direct mechanism. It seems that there is a big difference in the vascular effect between GTE and EGCG.

• Journal of the Korean Society of Costume
• /
• v.58 no.3
• /
• pp.116-122
• /
• 2008

This study aims at defining the meaning of Pobeckchuck in the historical view-point, which appeared in the History of Joseon Dynasty, regarding the periods from the ruling period of Sunjo to that of Sunjong as the latter part of history. Pobeckchuck used in King Sejong was redressed in accordance with the measurement in the Kyeonggukdadejeon(code), in which time one Pobeckchuck was 46.80cm long. It is known that Juchuck, Hwangjongchuck, Youngjochuck, Joraegichuck etc. which had been used in the ruling period of Sejong Dynasty, were used till the period of Youngjo. Also, the document shows that in the 12th ruling period of Sunjo, Pobeckchuck was used for measurement, and in the 20th ruling period of Sunjo, newly-made ruler was only used for the measurement of fields, but no more details about how long it was. But according to the document complied at that time, one Pobeckchuck was 46.80cm long, which fact reveals that the same measurement was used as in the ruling period of Sunjo. When all the measurement laws which were established in the 3rd year of Junghee, the 6th year of Kwangmu were abolished, Pobeckchuck was solely banned from its use, which fact offers a glimpse of how confusing at that period was. The comparison and examination among many documents in the latter part of Joseon Dynasty show the differences within about 4cm that one Pobeckchuck ranged from 44.80cm to 48.80cm long. But no other document on measurement appeared in the History of Joseon Dynasty, except for the 46.80cm. Thus, the 46.80cm corrected in the ruling period of Sunjo proves that one chuck in Pobeckchuck adopted by the dynasty was used as the measurement of length till the ruling period of Sunjong.

• Korean Journal of Human Ecology
• /
• v.16 no.3
• /
• pp.623-630
• /
• 2007

The remarkable fact regarding the History of Chosun Dynasty(from Jungjong- Youngjo) is that any slightest evidence can't be found that Pobeckchuck was used to measure clothes or various Pobecks. There remains the document that in the 22nd years of Myeonjong, Japan required that Pobeckchuck be used, but it couldn't be allowed because of the reason it was made in the former king. This fact raises the high possibility that Pobeckchuck could be the most trustworthy standardized ruler at that time, and in other point of view, it can be presumed that the measurement in the period of King Sejong continued to have been used until this time. It can be seen that the length of one Chuck of Pobeckchuck at this time must have been equivalent to 46. 73cm of Pobeckchuck of Samchuck in the period of Sejong. In the History of Sunjo Period, many records on Pobeckchuck can be found, which fact seemed to have rectified the measurement system which was disordered by military revolt, though the reason is not clear. Also a record can be found that in the period of Sunjo, Chinese envoy required the Sunjo Regime to use Pobeckchuck for the measurement of copper pillar, which record supports the fact that Pobeckchuck is the standardized ruler. Another record that in the 26th period of Youngjo, Pobeckchuck of Samchuck was corrected according to the Kyeongkukdaejeon shows that the length of Pobeckchuck was 46.80cm at that time. Also, the record which rectified many rulers with the comparison of Hwangjong-chuck, Ju-chuck, Joryeki-chuck, Yongjo-chuck, etc. with one another reveals that the rulers used in the period of Sejong continued to have been used unchanged until in the period of Youngjo.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.37 no.1
• /
• pp.90-100
• /
• 2013

This study uses a survey questionnaire to identify the major customer age class of adult women who frequently mountain climb as well as analyze their purchasing behavior and preference of mountain climbing pants. The field survey, classified the types of mountain climbing pants, selected the types of mountain climbing pants that consumers preferred, and then analyzed the degrees of satisfaction for mountain climbing pants based on an evaluation of wearing. Specifically, the patterns of mountain climbing pants preferred by national brands and licensed brands were compared and analyzed. The validities of commercially available mountain climbing pants were analyzed through an evaluation of wearing comfort and an evaluation of wearing on a 3D simulation of the human body. The basic data for the development of mountain climbing pants are presented based on the results. The survey questionnaire results indicate that the major class of women consumers of mountain climbing goods was in the 40s to 50s; in addition, the types they most wore were straight type and functional cut type. The preferred brand was KOLONSPORT (which occupies a 21.2% market share), followed by THE NORTH FACE (13.0%), K2 (11.5%) and Kolping (10.0%). The main reason (26.8% of responses) that they preferred these brands was functionality. The difference in measurement of climbing pants patterns could be analyzed accurately in the pattern analysis, the wearing evaluation by the self-sonsory test and evaluation of wearing comfort through 3D simulation. The results of ANOVA on motions and items indicates that no significant difference was found among motions; however, a significant difference was recognized among items. A comparison of straight type and functional cut type showed that the functional cut type excelled slightly in wearing comfort.

• Journal of Periodontal and Implant Science
• /
• v.50 no.3
• /
• pp.197-206
• /
• 2020

Purpose: The aim of this study was to determine the impact of different compressive forces on deproteinized bovine bone mineral (DBBM) particles covered by native bilayer collagen membrane (NBCM) during alveolar ridge preservation (ARP) in the molar area, and to identify any histomorphometric and clinical differences according to the compressive force applied. Methods: Sockets were filled with DBBM after tooth extraction, and different compressive forces (30 N and 5 N, respectively) were applied to the graft material in the test (30 N) and control (5 N) groups. The DBBM in both groups was covered with NBCM in a double-layered fashion. A crossed horizontal mattress suture (hidden X) was then made. A core biopsy was performed using a trephine bur without flap elevation at the implant placement site for histomorphometric evaluations after 4 months. The change of the marginal bone level was measured using radiography. Results: Twelve patients completed the study. The histomorphometric analysis demonstrated that the mean ratios of the areas of new bone, residual graft material, and soft tissue and the implant stability quotient did not differ significantly between the groups (P>0.05). However, the mean size of the residual graft material showed a significant intergroup difference (P<0.05). Conclusions: The application of 2 compressive forces (5 N, 30 N) on particulate DBBM grafts during open-healing ARP in the posterior area led to comparable new bone formation, implant feasibility and peri-implant bone level.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.40 no.1
• /
• pp.171-187
• /
• 2016

The study performed a comparison analysis of market brand patterns for slim-fit dress shirts and analyzed the body surface development figure of men in their 40s using 3D body scan data and developed slim-fit dress shirt patterns suitable for middle-aged men. The sizes of slim-fit dress shirt patterns showed a slight difference depending on brand. The overlap map of slim-fit dress shirt patterns for brands demonstrates how difference of one-dimensional sizes reflect on two-dimensional patterns. This map provides useful information for pattern design and allows and easy recognition of pattern size differences. A try-on system evaluation through 3D-Simulation allows a grasp of the fitness of neckline and size tolerance of under the arms in front, the silhouette of side lines, and overall fitness in front that also allows analysis of the front/back balance of a shirt in side, the size tolerance proportion in front/back, and the fitness of the arm-hole line. Thus, we obtained try-on results that were equivalent to wearing actual clothing. According to the drafting size suggested in the developed final pattern, the total width was 'C/2+5.5cm', and the front was set at 1cm bigger in the size difference of the front and back. The width of the front neck and the back neck was set identically at 'C/12', while the width of the front neck was set to 'C/12+1.5cm'. For the armhole depth, we added 'C/4+2cm', and '0.5cm and 1.5cm' for the width of the front and back to anthropometry. The results of the try-on evaluation through 3D-Simulation indicated that the fitness of the final slim-fit dress shirt pattern was superior to available slim-fit dress shirt patterns on the market and evaluated as superior to the types for middle-aged men.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2001.11a
• /
• pp.67-67
• /
• 2001

The structure zone model has been used to provide an overview of the relationship between the microstructure of the films deposited by PVD and the most prominent deposition condition.s. B.AMovchan and AV.Demchishin have proposed it firstls such model. They concluded that the general features of the resulting structures could be correlated into three zones depending on $T/T_m$. Here T m is the melting point of the coating material and T is the substrate temperature in kelvines. Zone 1 ($T/Tm_) is dominated by tapered macrograins with domed tops, zone 2 ($O.3) by columnar grains with denser boundaries and zone 3 ($T/T_m>O.5$) by equiaxed grains formed by recrystallization. J.AThomton has extended this model to include the effect of the sputtering gas pressure and found a fourth zone termed zone T(transition zone) consisting of a dense array of poorly defined fibrous grains. R.Messier found that the zone I-T boundary (fourth zone of Thorton) varies in a fashion similar to the film bias potential as a function of gas pressure. However, there has not nearly enough model for explaining the change in morphology with crystal orientation of the films. The structure zone model only provide an information about the morphology of the deposited film. In general, the nucleation and growth mechanism for granular and fine structure of the deposited films are very complex in an PVD technique because the morphology and orientation depend not only on the substrate temperature but also on the energy of deposition of the atoms or ions, the kinetic mechanism between metal atoms and argon or nitrogen gas, and even on the presence of impurities. In order to clarify these relationship, AI and Mg thin films were prepared on SPCC steel substrates by PVD techniques. The influence of gas pressures and bias voltages on their crystal orientation and morphology of the prepared films were investigated by SEM and XRD, respectively. And the effect of crystal orientation and morphology of the prepared films on corrosion resistance was estimated by measuring polarization curves in 3% NaCI solution.

• Journal of the Korean Society of Costume
• /
• v.58 no.10
• /
• pp.65-77
• /
• 2008

The purpose of this study is to analyze the correlation between the density, the Count and the width of cross section in 2D function through comparison the difference of simulated fabrics based on the various yarns, and to compare the 3D effect by Lay Mapping of diverse fabrics. The method of research is to weave the eight fabrics composed of cotton, linen, worsted, slender yarn, loop, $m{\acute{e}}lange$, woolen, and yarn twist with Hi-Tex program, and to practice 3D mapping with Hi-Print program. As a mapping object, the flared skirt which is a basic costume item is selected. As a result, the thickness of yarn in CAD system was fixed by the width of cross section rather than Count, especially by the width of core section not including the fluff section. The type of yarn such as cotton yarn, linen yarn, and worsted had effect on the shape of texture, but had few interrelations with dimension. In the case of 3D mapping, the textural characteristic and the dimension were presented precisely, whereas there were several limitations. First, the thickness of tissue has not been represented. Secondly, the effect of texture such as fuzzy look, loop was not expressed on the skirt outline including sideline and hemline. Thirdly, the difference of silhouette was not distinct. The common point in 2D and 3D operations is that the representation of texture is relatively accurate and that is difficult to measure and manifest of thickness, the side. For more professional digitalizing in fashion industry, above all in the domain of 3D, it must be supplement the subdivided and differentiated mapping process according to the texture, deviating from the existing analog-based organization which has to designate the form and silhouette suitable for tissue.

• Journal of the Society of Naval Architects of Korea
• /
• v.50 no.4
• /
• pp.224-231
• /
• 2013

The concept of the natural frequency is useful for understanding the characters of oscillating systems. However, when a circular cylinder floating horizontally on the water surface is heaving, due to the hydrodynamic forces, the system is not governed by the equation like that of the harmonic one. In this paper, in order to shed some lights on the more correct use of the concept of the natural frequency, a problem of the heaving circular cylinder is analyzed in the time domain. The equation of motion, an integro-differential equation, was derived following the fashion of Cummins (1962), and its coefficients including the retardation function were obtained using the numerical solution of Lee (2012). The equation was solved numerically, and the experiment was also carried out in the CNU flume. Using our numerical and experimental results, the natural frequency was defined as its average value given by the motion data excluding those of the initial stage. Our results were then compared with those of the existing investigations such as Maskell and Ursell (1970), Ito (1977) and Yeung (1982) as well as the newly obtained results of Lee (2012). Comparison showed that the natural frequency obtained here agrees well with that of Lee (2012), which was found through the frequency domain analysis. It was also shown that the approximation of heaving motion by a damped harmonic oscillation, which was regarded as suitable by most previous investigators, is not physically suitable for the reason that can be clearly shown through comparing the shape of MCFRs(Modulus of Complex Frequency Response). Furthermore, we found that although the previous approximations yield the damping ratio significantly different from our result the magnitude of natural frequency is not much different from our result.