• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1993.10a
• /
• pp.1196-1201
• /
• 1993

Test of Caterpillar Challenger 65 tractor which has rubber tracks, and articulated four wheel drive tractor with dual wheels and a mechanical front wheel drive tractor were conducted on an unplowed and plouwed wheat stubble field. The following parameters were analyzed : tractive efficiency (ηv), net tractive coefficient ($\phi$n), slip ($\sigma$) , drawbar pull(Fv), drawbar power (Pv) and forward velocity(v). The maximum net tractive coefficient was established at the tractive efficiency of 0.60 on the unplowed wheat stubble field : for the Challenger 65 tractor 0.855 ; 4WD 0.624 and MFWD 0.534 and on the plowed wheat stubble field with the tractive efficiency of 0.40 for the Challenger 65 tractor 0.82 : 4WD 0.57 and for tractor MFWD 0.48.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.8
• /
• pp.1102-1114
• /
• 2002

An electret filter is composed of permanently charged electret fibers and is widely used in applications requiring high collection efficiency and low-pressure drop. In this work, the collection efficiency of the filter media used in manufacturing cabin air filters was investigated by using poly-disperse particles when submicron particles were loaded. Long-term experiments were conducted by applying two different charging states, which were spray electrification and charge equilibrium by bipolar ionization. In order to investigate the effect of particle loading in filter media, NaCl particles were generated from 0.1% and 1% solutions by an atomizer. Liquid DOS particles were used to evaluate the effect of liquid particles on the collection efficiency of an electret filter. The results show significant effect of charge amount and size distribution of loading particles on the collection performance of a filter media in submicron region. Smaller particles loaded in electret fibers cause a more rapid degradation in collection efficiency and have lower minimum efficiency with time. The pressure drop of a filter media do rarely increase when the collection efficiency decreases to the minimum value. For the larger particles charged by spray electrification, which have charge amounts more than that of Boltzmann equilibrium charge distribution, the pressure drop of a filter media slowly increases in comparison with that of equilibrium charged particles. For DOS particles it is shown that the charging level of an electret filter severely decreases and the collection efficiency is below 10% in some particle size range.

• Korean Management Science Review
• /
• v.19 no.1
• /
• pp.117-128
• /
• 2002

In this Paper we investigate the performance of the five efficiency estimation methods which include the stochastic frontier model estimated by maximum likelihood (SFML), the stochastic frontier model estimated by corrected ordinary least squares (SFCOLS), the data envelopment analysis (DIA) model, the combined estimation of SFML and DEA (SFML + DEA), and the combined estimation of SFCOLS arid DIA (SFCOLS+ DEA) using Monte Carlo analysis. The results include: 1) SFML provides most accurate efficiency estimates for the sample sloe 150 or over,2) SFML+DEAor SFCOLS + DIA Perform better for the cases with sample sloe 25, 50, and low random errors, 3) SFCOLS performs better for the close with sample sloe 25, 50, and very high random errors.

• Nuclear Engineering and Technology
• /
• v.41 no.5
• /
• pp.723-728
• /
• 2009

The response property of the CZT detector ($5{\times}5{\times}5\;mm^3$), widely used in photon spectroscopy, was evaluated by considering the charge collection efficiency, which depends on the interaction position of incident radiation, A quantitative analysis of the energy spectra obtained from the CZT detector was also performed to investigate the tail effect at the low energy side of the full energy peak. The collection efficiency of electrons and holes to the two electrodes (i.e., cathode and anode) was calculated from the Hecht equation, and radiation transport analysis was performed by two Monte Carlo codes, Geant4 and MCNPX. The radiation source was assumed to be 59.5 keV gamma rays emitted from a $^{241}Am$ source into the cathode surface of this detector, and the detector was assumed to be biased to 500 V between the two electrodes. Through the comparison of the results between the Geant4 calculation considering the charge collection efficiency and the ideal case from MCNPX, an pronounced difference of 4 keV was found in the full energy peak position. The tail effect at the low energy side of the full energy peak was confirmed to be caused by the collection efficiency of electrons and holes. In more detail, it was shown that the tail height caused by the charge collection efficiency went up to 1000 times the pulse height in the same energy bin at the calculation without considering the charge collection efficiency. It is, therefore, apparent that research considering the charge collection efficiency is necessary in order to properly analyze the characteristics of CZT detectors.

• Steel and Composite Structures
• /
• v.37 no.2
• /
• pp.193-209
• /
• 2020

In this paper, the efficiency of five Machine Learning (ML) methods consisting of Deep Learning (DL), Support Vector Machine (SVM), Random Forest (RF), Decision Tree (DT), and Gradient Tree Booting (GTB) for regression and classification of the Ultimate Load Factor (ULF) of nonlinear inelastic steel frames is compared. For this purpose, a two-story, a six-story, and a twenty-story space frame are considered. An advanced nonlinear inelastic analysis is carried out for the steel frames to generate datasets for the training of the considered ML methods. In each dataset, the input variables are the geometric features of W-sections and the output variable is the ULF of the frame. The comparison between the five ML methods is made in terms of the mean-squared-error (MSE) for the regression models and the accuracy for the classification models, respectively. Moreover, the ULF distribution curve is calculated for each frame and the strength failure probability is estimated. It is found that the GTB method has the best efficiency in both regression and classification of ULF regardless of the number of training samples and the space frames considered.

• Structural Engineering and Mechanics
• /
• v.49 no.3
• /
• pp.297-309
• /
• 2014

Under lateral loads Framed Tube (FT) system exhibits reduction of cantilever efficiency due to the effect of shear lag. Braced Tube (BT) represents a valuable solution to overcome shear lag problems by stiffening the exterior frame with diagonal braced members. This study investigates the effect of shear lag on BT and FT under wind load. Shear lag and top-level displacement results are compared with previous findings by researchers on FT and BT systems. The investigation of the effect of various configurations in BT on the reduction the shear lag is another objective of this study. The efficiency of each structure is evaluated using the linear response spectrum analysis to obtain shear lag. STADD Pro software is used to run the dynamic analysis of the models. Results show there is relatively less shear lag in all the BT configurations compared to the FT structural system. Moreover, the comparison of the obtained result with those derived by previous studies shows that shear lag is not proportional to lateral displacement. With respect to results, optimum BT configuration in term of lower shear lag caused by lateral loads is presented.

• Journal of Power Electronics
• /
• v.11 no.5
• /
• pp.621-631
• /
• 2011

In space qualified DC-DC converters, optimization of the following electrical characteristics is of greater interest in comparison with other specifications; power loss/efficiency, output voltage ripple and volume/weight. The main goal of this paper is to present an appropriate solution for optimizing the above mentioned characteristics. For this purpose, a comprehensive power loss model of a DC-DC converter is fully developed. Proper models are also demonstrated for assessment of the output voltage ripple and the utilized transformer volume as the bulkiest component in a DC-DC converter. In order to provide a test bed for evaluation of the proposed models, a 50W push-pull DC-DC converter is designed and implemented. Finally, a novel cost function with three assigned weight functions is proposed in order to have a trade-off among the power loss, the output voltage ripple and the utilized transformer volume of the converter. The cost function is optimized for applications in which volume has the highest priority in comparison with power loss and ripple. The optimization results show that the transformer volume can be decreased by up to 51% and this result is verified by experimental results. The developed models and algorithms in this paper can be used for other DC-DC converter topologies with some minor modifications.

• Journal of Power Electronics
• /
• v.19 no.4
• /
• pp.894-906
• /
• 2019

In this paper, a DC-DC converter is proposed based on the Cuk converter. The proposed converter has high efficiency and it can be used in multilevel DC-DC converters. A reduction of the inductors size in comparison to Cuk converter and a reduction in the inductors resistance negative effects on efficiency are the important points of the proposed converter. Its voltage ripple is reduced when compared to other converters. Its output voltage has a high quality and does not contain spikes. A theoretical analysis demonstrates the positive points of the proposed converter. The design and analysis of the converter are done in continues conduction mode (CCM). Experiments confirm the obtained theoretical equations. The proposed converter voltage gain is similar to that of a conventional Boost converter. As a result, they are compared. The comparison illustrates the advantages of the proposed converter and its higher quality. Furthermore, a prototype of the proposed converter and its combination with a 2x multiplier are built in the lab. Experimental results validate the analysis. In addition, they are in good agreements with each other.

• Journal of Power Electronics
• /
• v.14 no.2
• /
• pp.203-216
• /
• 2014

In the conventional dc-dc converter, a pair of additional diode and the adjacent passive component capacitor/inductor can be added to the circuit with an X-shape connection, which generates a family of new topologies. The novel circuits, also called diode-assisted dc-dc converter, enhance the voltage boost/buck capability and have a great potential for high step-up/step-down power conversions. This paper mainly investigates and compares conventional dc-dc converter and diode-assisted dc-dc converter in wide range power conversion from the aspects of silicon devices, passive components requirements, electro-magnetic interference (EMI) and efficiency. Then, a comprehensive comparison example of a high step-up power conversion system was carried out. The two kinds of boost dc-dc converters operate under the same operation conditions. Mathematical analysis and experiment results verify that diode-assisted dc-dc converters are very promising for simultaneous high efficiency and high step-up/step-down power conversion in distributed power supply systems.

• Journal of the Korea Furniture Society
• /
• v.20 no.3
• /
• pp.239-246
• /
• 2009

The joinery technique, as one of manufacturing techniques for the wooden furniture, influences the production process, the economic efficiency, and the diversification of design. Especially, the usage of machine tools can determine how much the students can enhance their design expression capabilities during the practice class in furniture design courses of domestic universities, in accordance with whether to utilize the machine tools or not, and how much and frequent to use the machine tools. The study proved that the joinery techniques, based on the high-tech machine, has more efficiencies in the various aspects, including the easiness to manufacture the products, and the diversity of design than the joinery technique, based on the handcraft-only. As the ground of this, this study estimated the time to produce the wooden furniture by machine tools and by handcraft-only, each. Also, this study show the comparison of the features of three different joinery techniques. On the basis of this comparison, this study made the conclusion that the machine-based joinery technique, which is used in the practice class, is the best method to bring the best results in manufacturing the wooden furniture.