• Korean Journal of Optics and Photonics
• /
• v.15 no.5
• /
• pp.423-428
• /
• 2004

The development of a compact and high performance MWIR thermal imaging sensor based on the SOFRADIR 320${\times}$240 element IRCCD detector is described. The sensor has 20 magnification zoom optics with the maximum 40$^{\circ}$${\times}$30$^{\circ}$ of super wide field of view and 7.6 cycles/mrad of resolving power with the operation of attached micro-scanning system. In order to correct nonuniformities of detector arrays, we have proposed a multi-point correction method using defocusing of the optics and we have acquired the highest quality images. The MRTD of our system shows good results below 0.05K at spatial frequency 1 cycles/mrad at narrow field of view. Experimental data and obtained performances are presented and discussed.

• Journal of the Institute of Convergence Signal Processing
• /
• v.10 no.3
• /
• pp.170-175
• /
• 2009

In this paper, we propose real time automatic speaker verification (ASV) system to protect personal information on personal digital assistant (PDA) device. Recently, the capacity of PDA has extended and been popular, especially for mobile environment such as mobile commerce (M-commerce). However, there still exist lots of difficulties for practical application of ASV utility to PDA device because it requires too much computational complexity. To solve this problem, we apply the method to relieve the computational burden by performing the preprocessing such as spectral subtraction and speech detection during the speech utterance. Also by applying the hidden Markov model (HMM) optimal state alignment and the sequential probability ratio test (SPRT), we can get much faster processing results. The whole system implementation is simple and compact enough to fit well with PDA device's limited memory and low CPU speed.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1994.04c
• /
• pp.6-6
• /
• 1994

Har dmaterials such as cemented carbides with or without coated layer, cermets, ceramics and diamond or c-BN high pressure sintered compact are used for cutting tools, wear -resistant parts, rock drilling bits and/or high pressure vessels. These hardmaterials contain not only hard phase, but also second consituent as the element for forming ductile phase and/or sintering aid, and the mechanical properties of each material depend on (1) the amount of the second constituent as well as (2) the grain size of the hard phase. The hardness of each material mainly depends on these two factors. The fracture strength, however, largely depends on other microstructur a1 factors as well as the above two factors. For all hardmaterials, the fracture strength is consider ably affected by (3) the size of microstructur a1 defect which acts as the fracture source. In cemented carbides, the following factors which are generated mainly due to the addition of the second constituent are also important; (4) the variation of the carbon content in the normal phase region free from V-phase and graphite phase, (5) the precipitation of $Co_3$ during heating at about $800^{\circ}C$,(6) the domain size of binder phase, and (7) the formation of ${\beta}$-free layer or Co-rich layer near the surface of sintered compacts. For cemented carbides coated with thin hard substance, the important factors are as follows; (8) the kind of coated substance, (9) the formation of ${\eta}$-phase layer at the interface between coated layer and substrate, (10) the type of residual stress (tension or compression) in the coated layer which depends on the kind of coating method (CVD or PVD), and (11) the properties of the substrate, and (12) the combination, coherency and periodicity of multi-layers. In the lecture, the details of these factors and their effect on the strength will be explained.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.41 no.3
• /
• pp.55-65
• /
• 2004

When a neural network is used to solve a given problem it is necessary to match the complexity of the network to that of the problem because the complexity of the network significantly affects its learning capability and generalization performance. Thus, it is desirable to have an algorithm that can find appropriate network structures in a self-organizing way. This paper proposes algorithms which automatically organize feed forward multi-layer neural networks with sigmoid hidden neurons for given problems. Using both constructive procedures and pruning procedures, the proposed algorithms try to find the near optimal network, which is compact and shows good generalization performance. The performances of the proposed algorithms are tested on four function regression problems. The results demonstrate that our algorithms successfully generate near-optimal networks in comparison with the previous method and the neural networks of fixed topology.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.2
• /
• pp.101-107
• /
• 2016

This paper presents the characteristics of a double-cone broadband antenna with compact and three-dimensional structure that can be used in UWB system. The theoretical analysis is conducted using a finite difference time domain(FDTD) method. The parameters are the radius, a height of broadband double-cone antennas with shorting plate, and the number of plates on a ground plane. This paper examines influence of structural parameters on return loss. The results show that a condition for an optimum structure of broadband double-cone antennas with shorting plate exists. It also shows that the broadband double-cone antennas with shorting plate have radiation patterns similar to those of a dipole antenna. To verify the theoretical analysis, computed results are compared to experimental results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.4
• /
• pp.424-434
• /
• 2015

Adaptive beamforming algorithms have been widely used to remove interference and jamming in the phased array radar system. Advances in the field programmable gate array(FPGA) technology now make possible the real time processing of adaptive beamforming (ABF) algorithm. In this paper, the FPGA based real-time implementation method of adaptive beamforming system(beamformer) in the pre-processor module for active electronically scanned array(AESA) radar is proposed. A compact FPGA-based adaptive beamformer is developed using commercial off the shelf(COTS) FPGA board with communication via OpenVPX(Virtual Path Cross-connect) backplane. This beamformer comprises a number of high speed complex processing including QR decomposition & back substitution for matrix inversion and complex vector/matrix calculations. The implemented result shows that the adaptive beamforming patterns through FPGA correspond with results of simulation through Matlab. And also confirms the possibility of application in AESA radar due to the real time processing of ABF algorithm through FPGA.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.9
• /
• pp.1048-1057
• /
• 2012

In this paper, a new compact dual-band unequal power divider is suggested. Instead of the quarter wavelength transmission line(TX-line)s for the branches of the conventional Wilkinson's power divider, we use composite right- and left-handed(CRLH) phase-shift lines and can reduce the physical length. With the non-linear dispersion of the meta-meterial, each branch in the proposed divider is designed to have $+90^{\circ}$ and $-90^{\circ}$ at $f_1$ and $f_2$ respectively. To validate the proposed method, the performances of the circuit and full-wave simulation results are shown with the CRLH dispersion curve. The measurement results are compared with the simulation results. Also, the size reduction effect by the proposed scheme is addressed.

• The Bulletin of The Korean Astronomical Society
• /
• v.39 no.1
• /
• pp.50.1-50.1
• /
• 2014

The Multi-purpose InfraRed Imaging System (MIRIS) is the main payload of Science and Technology Satellite 3 (STSAT-3), which was launched onboard Dnepr rocket from Russian Yasny Launch Base in November 2013. The MIRIS is an infrared (IR) camera, and the telescope has to be cooled down to below 200K in order to reduce thermal background noise. For the effective cooling and low-power consumption, we applied passive cooling method to the thermal design of the MIRIS. We also conducted thermal analysis and tested for the passive cooling before the launch of STSAT-3. After the launch, we have received State-of-Health (SOH) data from the satellite on orbit, including temperature monitoring results. It is important that the temperature of the telescope was shown to be cooled down to below 200K. In this paper, we present both the temperature data of the MIRIS on orbit and the thermal analysis results in the laboratory. We also compare these results and discuss the verification of the passive cooling.

• Korean Chemical Engineering Research
• /
• v.51 no.5
• /
• pp.602-608
• /
• 2013

Gas hydrate studies are attracting attention of many researchers as an innovative, economic and environmentally friendly technology when it is applied to $CO_2$ capture, transport, and storage. In this study, we investigated whether $CO_2$ hydrate shows the self-preservation effect or not, that is the key property for developing a novel $CO_2$ transport/storage method. Especially the degree of self-preservation effect for $CO_2$ hydrate was studied according to the particle size of $CO_2$ hydrate samples. We prepared three kinds of $CO_2$ hydrate samples varying their particle diameter as millimeter, micron and nano size and measured their change of weight at $-15{\sim}-30^{\circ}C$ under atmospheric pressure during 3 weeks. According to our experimental result, the lower temperature, larger particle size, and compact structure for higher density are the better conditions for obtaining self-preservation effect.

• Journal of the Korean Society of Costume
• /
• v.65 no.5
• /
• pp.103-112
• /
• 2015

This study examines the fashion illustrations textbooks that have been published in the domestic market, and identifies its characteristics and problems in regards to its use in developing creative students. The purpose of the study is to propose ways to improve the development of the fashion illustration textbooks. The research method of this study are as follows: First, the teaching materials on fashion illustration in Korea were researched to examine the current state of publication. Second, its contents were analyzed to identify its characteristics. Third, an improvement plan of educational materials on fashion illustration in Korea were proposed. As for the scope of study, 18 volumes of fashion illustration teaching materials published in Korea during 2004-2014 were targeted. It should be noted that translated publications, digital fashion illustration materials and teaching materials for specialized and professional organizations were excluded. Conclusions of this study are as follows: First, examination of the textbooks revealed that additional content is needed regarding theoretical understanding of fashion illustration, as well as illustrations of men and children, as there was an insufficient amount of those topics. Second, the contents on the illustration application using current trends were lacking in the unit on illustration application. Accordingly, it is necessary to develop contents that reflect these trends. Lastly, the textbooks should be packaged with compact discs CDs containing video clips to assist students to get a better grasp of the material. The result of this study can be used to develop new teaching materials on fashion illustration, and be utilized as basic information in the curriculum design of fashion illustration.