• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 Proceedings ICPE 01 2001 International Conference on Power Electronics
• /
• pp.761-767
• /
• 2001

In this paper, filtering techniques to reduce the adverse effects of motor leads on high-frequency PWM inverter fed AC motor drives will be examined. The filter was designed to keep the motor terminal from the cable surge impedance to reduce overvoltage reflections, ringing, and the dv/dt, di/dt. Therefore, filtering techniques are investigated to reduce the motor terminal overvoltage, ringing, and EMI noise in inverter fed ac motor drive systems. The output filter is used to limit the rate of the inverter output voltage and reduce EMI(common mode noise) to the motor. The performance of the output filter is evaluated through simulations (PSIM) and experiment on PWM inverter-fed ac motor drive(3phase, 3hp(2.2kw), input voltage 220/380V, induction motor). An experimental PWM drive system reduction of conducted EMI was implemented on an available TMS320C31 microprocessor control board. Finally, experimental results showed that the inverter output filter reduces more CM noise than the LPF(low pass filter) and reduce overvoltage and ringing at the motor terminal.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제10권4호
• /
• pp.300-308
• /
• 2010

This paper describes the development of a low-power electrocardiogram (ECG) touch sensor intended for the use with two dry metal electrodes. An equivalent ECG extraction circuit model encountered in a ground-free two-electrode configuration is investigated for an optimal sensor read-out circuit design criteria. From the equivalent circuit model, (1) maximum sensor resolution is derived based on the electrode's background thermal noise, which originates from high electrode-skin contact impedance, together with the input referred noise of instrumentation amplifier (IA), (2) 60 Hz electrostatic coupling from mains and motion artifact are also considered to determine minimum requirement of common mode rejection ratio (CMRR) and input impedance of IA. A dedicated ECG read-out front end incorporating chopping scheme is introduced to provide an input referred circuit noise of 1.3 ${\mu}V_{rms}$ over 0.5 Hz ~ 200 Hz, CMRR of IA > 100 dB, sensor resolution of 7 bits, and dissipating only 36 ${\mu}W$. Together with 8 bits synchronous successive approximation register (SAR) ADC, the sensor IC chip is implemented in 0.18 ${\mu}m$ CMOS technology and integrated on a 5 cm $\times$ 8 cm PCB with two copper patterned electrodes. With the help of proposed touch sensor, ECG signal containing QRS complex and P, T waves are successfully extracted by simply touching the electrodes with two thumbs.

• 한국의학물리학회지:의학물리
• /
• 제13권3호
• /
• pp.156-162
• /
• 2002

본 연구에서는 뇌파 신호를 측정할 수 있는 고정밀도의 뇌파측정시스템을 제작하였다. 전치증폭기는 분리증폭기의 방식으로 잡음제거 능력을 향상하였으며, 높은 사용자 안전도를 갖도록 제작하였다. 제작된 뇌파측정시스템은 주파수 대역별로 알파, 베타, 세타로 자동으로 분류될 수 있도록 A/D 변환하였다. 변환된 데이터는 DSP를 이용하여 실시간으로 FFT처리를 하였다. 실험은 현재 병력이 없고 건강 상태가 양호한 만 20세에서 26세까지의 학생을 대상으로 실시하였다. 외부의 물리적인 자극이 뇌파에 미치는 영향을 조사하기 위하여, 현재 시판되고 있는 뇌파 자극기인 MS제품을 이용하여 시각과 청각의 두 상태로 외부자극을 주고, 그 반응을 측정하여 비교하였다. 피검자의 감성평가 측정결과 본 연구에서 제작한 뇌파측정기가 유효함을 확인하였으며, 심리적인 상태변화를 조사할 수 있었다.

• Earthquakes and Structures
• /
• 제22권1호
• /
• pp.1-13
• /
• 2022

When a building suffers damages under moderate to severe loading condition, its physical properties such as damping and stiffness parameters will change. There are different practical methods besides various numerical procedures that have successfully detected a range of these changes. Almost all the previous proposed methods used to work with translational components of mode shapes, probably because extracting these components is more common in vibrational tests. This study set out to investigate the influence of using both rotational and translational components of mode shapes, in detecting damages in 3-D steel structures elements. Three different sets of measured components of mode shapes are examined: translational, rotational, and also rotational/translational components in all joints. In order to validate our assumptions two different steel frames with three damage scenarios are considered. An iterative model updating program is developed in the MATLAB software that uses the OpenSees as its finite element analysis engine. Extensive analysis shows that employing rotational components results in more precise prediction of damage location and its intensity. Since measuring rotational components of mode shapes still is not very convenient, modal dynamic expansion technique is applied to generate rotational components from measured translational ones. The findings indicated that the developed model updating program is really efficient in damage detection even with generated data and considering noise effects. Moreover, methods which use rotational components of mode shapes can predict damage's location and its intensity more precisely than the ones which only work with translational data.

• 전자공학회논문지
• /
• 제50권12호
• /
• pp.40-48
• /
• 2013

본 논문에서는 0.18um CMOS(1P6M) 공정을 이용하여 무인차량용 단거리 라이다 시스템을 위한 멀티채널 트랜스임피던스 증폭기(TIA) 어레이 회로를 구현하였다. 트랜스임피던스 증폭기 어레이 구조는 전압모드 $4{\times}4$ 채널 Inverter TIA 어레이와 전류모드 $4{\times}4$ 채널 Common-Gate(CG) TIA 어레이 두 가지를 설계했으며, 전체적으로 $4{\times}8$의 32-채널을 갖도록 설계하였다. 먼저, Inverter TIA는 피드백 저항을 가진 Inverter 입력구조와 CML 출력버퍼단으로 구성되어 있으며, 저잡음 및 저전력 특성뿐 아니라, virtual ground를 갖도록 설계함으로써 DC 전류조절이 가능하여 이득과 출력 임피던스 컨트롤이 가능하도록 하였다. 또한, CG-TIA는 on-chip bandgap reference로부터 bias 전압을 이용하고, 소스팔로워 출력버퍼를 사용하여 고주파수 이득을 높였으며, 기본적인 구조 상 CG-TIA는 채널당 칩 면적이 Inverter TIA에 비해 1.26배 작게 설계되었다. 포스트 레이아웃 시뮬레이션 결과, 제안한 Inverter TIA 어레이는 각 채널당 57.5-dB${\Omega}$ 트랜스임피던스 이득, 340-MHz 대역폭, 3.7-pA/sqrt(Hz) 평균 잡음전류 스펙트럼 밀도, 및 2.84-mW (16채널 45.4-mW) 전력소모를 가졌다. CG-TIA 어레이는 채널당 54.5-dB${\Omega}$ 트랜스임피던스 이득, 360-MHz 대역폭, 9.17-pA/sqrt(Hz) 평균 잡음전류 스펙트럼 밀도, 4.24-mW (16채널 67.8-mW) 전력소모를 가졌다. 단, 펄스 시뮬레이션 결과, CG-TIA 어레이가 200-500-Mb/s 동작속도에서 훨씬 깨끗하게 구분 가능한 출력펄스를 보였다.

• 전력전자학회논문지
• /
• 제22권4호
• /
• pp.277-284
• /
• 2017

For passive power factor correction, the valley fill circuit approach is attractive for low power applications because of low cost, high efficiency, and simple circuit design. However, to vouch for the product quality, two dc-link capacitors in the valley fill circuit should be selected to withstand the peak rectified ac input voltage. The common mode (CM) and differential mode (DM) choke should be used to suppress the electromagnetic interference (EMI) noise, thereby resulting in large size volume product. This paper presents the practical design and implementation of a valley fill flyback converter with reduced dc link capacitors and EMI magnetic volumes. By using the proposed over voltage protection circuit, dc-link capacitors in the valley fill circuit can be selected to withstand half the peak rectified ac input voltage, and the proposed CM/DM choke can be successfully adopted. The proposed circuit effectiveness is shown by simulation and experimentally verified by a 78W prototype.

• 한국산업정보학회논문지
• /
• 제18권5호
• /
• pp.15-18
• /
• 2013

본 논문은 뇌전도 신호 처리를 위한 아날로그 전단부를 제시한다. 일반적으로 뇌전도 신호는 낮은 주파수 대역에 존재하고 신호의 크기가 미약하므로 이를 처리하기 위한 아날로그 전단부는 높은 전압 이득 및 공통모드 제거비를 가져야 하며 저주파 잡음을 효과적으로 억제해야 한다. 본 논문에서 제시하는 아날로그 전단부는 가변 이득 계측 증폭기와 대역통과 필터로 구성되어 있다. 낮은 주파수의 잡음을 제거하기 위하여 주파수 chopping을 적용하였다. 본 논문의 회로는 0.18um CMOS 공정을 이용하여 제작하였으며 측정 결과 최대 60dB의 전압이득과 100dB 이상의 공통모드 제거비를 내는 것을 확인하였다.

• 대한의용생체공학회:의공학회지
• /
• 제26권4호
• /
• pp.215-221
• /
• 2005

We describe the development of a prototype multi-channel electrical impedance tomography (EIT) system. The EIT system can be equipped with either a single-ended current source or a balanced current source. Each current source can inject current between any chosen pair of electrodes. In order to reduce the data acquisition time, we implemented multiple digital voltmeters simultaneously acquiring and demodulating voltage signals. Each voltmeter measures a differential voltage between a fixed pair of adjacent electrodes. All voltmeters are configured in a radially symmetric architecture to optimize the routing of wires and minimize cross-talks. To maximize the signal-to-noise ratio, we implemented techniques such as digital waveform generation, Howland current pump circuit with a generalized impedance converter, digital phase-sensitive demodulation, tri-axial cables with both grounded and driven shields, and others. The performance of the EIT system was evaluated in terms of common-mode rejection ratio, signal-to-noise ratio, and reciprocity error. Future design of a more innovative EIT system including battery operation, miniaturization, and wireless techniques is suggested.

• 센서학회지
• /
• 제26권5호
• /
• pp.342-347
• /
• 2017

We present a precision instrument amplifier (IA) designed for bio-potential acquisition. The proposed IA employs a capacitively coupled instrument amplifier (CCIA) structure to achieve a rail-to-rail input common-mode range and low gain error. A positive feedback loop is applied to boost the input impedance. Also, DC servo loop (DSL) with pseudo resistors is adopted to suppress electrode offset for bio-potential sensing. The proposed amplifier was designed in a $0.18{\mu}m$ CMOS technology with 1.8V supply voltage. Simulation results show the integrated noise of $1.276{\mu}Vrms$ in a frequency range from 0.01 Hz to 1 KHz, 65dB SNR, 118dB CMRR, and $58M{\Omega}$ input impedance respectively. The total current of IA is $38{\mu}A$. It occupies $740{\mu}m$ by $1300{\mu}m$ including the passive on-chip low pass filter.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제2B권3호
• /
• pp.115-124
• /
• 2002

This paper presents an active auxiliary edge-resonant DC link snubber with a ringing surge damper and a three-phase voltage source type zero voltage soft-switching inverter with the resonat snubber treated here for the AC servo motor driver applications. The operation of the active auxiliary edge-resonant DC link snubber circuit with PWM voltage is described, together with the practical design method to select its circuit parameters. The three-phase voltage source type soft-switching inverter with a single edge-resonant DC link snubber treated here is evaluated and discussed for the small-scale permanent magnet (PM) type-AC servo motor driver from an experimental point of view. In addition to these, the AC motor stator current and its motor speed response for the proposed three-phase soft-switching inverter employing Intelligent Power Module(IPM) based on IGBTS are compared with those of the conventional three-phase hard-switching inverter using IPM. The practical effectiveness of the three-phase soft-switching inverter-fed permanent magnet type AC motor speed tracking servo driver is proven on the basis of the common mode current in a novel type three-phase soft-switching inverter-fed AC motor side and the conductive noise on the mains terminal interface voltage as compared with those of the conventional three-phase hard-switching inverter-fed permanent magnet type AC servo motor driver for the speed tracking applications.