• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.4
• /
• pp.89-95
• /
• 2013

In this work, the evaluation of swirl nozzle injector performance was conducted by investigating effective area ($A_{eff}$), injection mass ($m_{inj}$), injection rate ($Q_{inj}$), and injection delay ($t_{delay}$) under various test conditions. To achieve these, fuel injection analysis system which was composed of fuel supply system, injection system, and control system was installed. At the same time, the swirl nozzle that had 12 orifice hole with $120^{\circ}$ injection angle was used in this work. It was revealed that the difference of injection mass ($m_{inj}$) between base and swirl nozzle injector increased as the injection pressure ($P_{inj}$) and energizing duration ($t_{eng}$) decreased under the same test conditions. The maximum injection rate ($Q_{inj}$) of swirl nozzle injector was higher than base nozzle injector about 2~5%. The injection performance of swirl nozzle was better than base nozzle at low injection pressure ($P_{inj}$) and short energizing duration ($t_{eng}$) conditions.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.1
• /
• pp.25-32
• /
• 2010

With the latest automobile technology, though the third generation common rail system requires high injection pressures up to 1,800bar, the next generation diesel engine is expected to require more higher pressures than the third generation. The common rail pipe requires higher strength because it is one of the parts in the common rail system, which is influenced directly by fuel under high pressure. Preform design is very important for preventing head of the common rail pipe from folding in the heading process. In this study, die angle, curvature, outer diameter of die and length of trapped part are selected as main parameters to obtain best preform shape minimizing radius of folding. Therefore optimal design is carried out by finite element analysis and Taguchi method through main parameters. Results of the finite element analysis have good agreements with those of the experiments in the actual field.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.6
• /
• pp.107-116
• /
• 2012

In this study, the trucks(2.9-liter) have been developed to use DME as fuel, and performance test of the vehicle's DME engine, power, emissions, fuel economy and vehicle aspects was conducted. For experiments, the fuel system(common-rail injectors and high-pressure pump included) and the engine control logic was developed, and ECU mapping was performed. As a result, the rail pressure from 40MPa to approximately 65% increase compared to the base injector has been confirmed that. Also, the pump discharge flow is 15.5 kg/h when the fuel rail pressure is 400rpm(40MPa), and the pump discharge flow is 92.1 kg/h when the fuel rail pressure is 2,000rpm(40MPa). The maximum value of full-load torque capability is 25.5 kgfm(based on 2,000 rpm), and more than 90% compared to the level of the diesel engine were obtained. The DME vehicle was developed in this study, 120 km/h can drive to the stable, and calculated in accordance with the carbon-balance method of fuel consumptions is 5.7 km/L.

• Journal of Mechanical Science and Technology
• /
• v.20 no.9
• /
• pp.1436-1448
• /
• 2006

This paper describes the effects of injection rate shaping on the combustion, fuel consumption and emission of $NO_x$ and soot of a medium duty diesel engine. The focus is on the influence of four different injection rate shapes, square type 1, square type 2, boot and ramp, with a variation of maximum injection pressure and start of injection (SOI). The experiments were carried out on a 1 liter single cylinder research diesel engine equipped with an amplifier-piston common rail injection system, allowing the adjustment of the injection pressure during the injection event and thus injection rate as desired. Two strategies to maintain the injected fuel mass constant were followed. One where rate shaping is applied at constant injection duration with different peak injection pressure and one strategy where rate shaping is applied at a constant peak injection pressure, but with variable injection duration. Injection rate shaping was found to have a large effect on the premixed and diffusion combustion, a significant influence on $NO_x$ emissions and depending on the followed strategy, moderate or no influence on soot emission. Only small effects on indicated fuel consumption were found.

• 한국연소학회:학술대회논문집
• /
• 2002.06a
• /
• pp.33-38
• /
• 2002

An optical single cylinder diesel engine equipped with a common-rail injection system has been built to investigate diesel combustion and emission characteristics. Three optical widows (piston crown quartz for bottom view of the cylinder, upper piston quartz for allowing laser sheet and liner quartz for side view) have been placed in the optical engine to visualize spray characteristics and combustion process inside the cylinder. Before doing further research using various optical diagnostics with the optical engine, fundamental combustion experiments and flame visualization incorporating a high speed motion analyser have been carried out with a wide range of engine operating conditions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.5
• /
• pp.40-57
• /
• 2004

The effects of triple (pilot, main and after) injection on combustion and emission characteristics in a HSDI (High-Speed Direct Injection) diesel engine were investigated using a single-cylinder optical diesel engine equipped with a common-rail injection system. The pilot injection affected the spray and combustion evolution of the following main injection. It was found that the pilot injection reduced the ignition delay, which led to lowered NOx (Nitric Oxides) level, and increased IMEP (Indicated Mean Effective Pressure) due to slow combustion pace during an expansion stroke. The after-injection was shown to be effective in reducing PM (Particulate Matter) even when a small amount of fuel was added. The results suggest that a proper combination of individual injection strategy could bring about a good synergetic effect on engine performance and emission.

• Journal of Institute of Convergence Technology
• /
• v.2 no.1
• /
• pp.24-30
• /
• 2012

In this study, the trucks(2.9-liter) have been developed to use DME as fuel, and performance test of the vehicle's DME engine, power, emissions, fuel economy and vehicle aspects was conducted. For experiments, the fuel system(common-rail injectors and high-pressure pump included) and the engine control logic was developed, and ECU mapping was performed. As a result, the rail pressure from 40MPa to approximately 65% increase compared to the base injector has been confirmed that. Also, the pump discharge flow is 15.5 kg/h when the fuel rail pressure is 400rpm(40 MPa), and the pump discharge flow is 92.1 kg/h when the fuel rail pressure is 2,000rpm(40MPa). The maximum value of full-load torque capability is 25.5kgfm(based on 2,000rpm), and more than 90% compared to the level of the diesel engine were obtained. The DME vehicle was developed in this study, 120 km/h can drive to the stable, and calculated in accordance with the carbon-balance method of fuel consumptions is 5.7 km/L.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.1
• /
• pp.53-59
• /
• 2011

The using of diesel engine will be increased in the world for fuel economy. But diesel engine emits harmful emissions such as much NOx, smoke etc. In this study, experiments were performed to investigate the spray characteristics of diesel spray in a common-rail system according to fuel temperature, injection pressure, injection period and fuel viscosity etc. using a high speed video camera. Diesel oil has different spray patten due to injection pressure and injection period in a common-rail system. A Filter pressure was influenced by fuel temperature which was turned to fuel viscosity related to a fluid flowing. The effect of the bio-diesel fuel mixing ratio on the spray and atomization characteristics was also investigated at various experimental conditions. It shows that the droplet atomization characteristics of bio-diesel fuel showed deteriorated results as the mixing ratio of biodiesel increased because of the high viscosity.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.3019-3025
• /
• 2008

An experimental study was performed to assess the effect of diesel and JP-8 aviation fuel on the spray characteristics, performance and emissions in a single cylinder optical diesel engine. Both fuels were injected via an 8-hole solenoid-driven injector in a common-rail injection system. For better understanding of spray development, the macroscopic images were captured with high speed camera, offered evidences for the results of performance and emissions. From macroscopic spray images, the spray tip penetration of JP-8 shorter than that of diesel while spray angle of JP-8 was wider than that of diesel. It indicates that the vaporization of JP-8 is superior to that of diesel. The lower cetane number of JP-8 resulted in increased portion of premixed combustion. The IMEP with JP-8 is lower than that of diesel-fueled engine. Especially, using JP-8 has a potential for reducing soot.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.12
• /
• pp.1305-1311
• /
• 2004

This study presents a mathematical model and a sliding mode observer of the injection system for common rail diesel engines. The injector model consists of three subsystems: the actuator subsystem, the mechanical subsystem, and the hydraulic subsystem. In the actuator subsystem, the constitutive relations of piezoelectricity are used to model the actuator made up of piezoelectric material. Based on the proposed model, the observer estimates the injection rate and injection timing, and can play a vital role of sensorless control of fuel injection in the near future. The sliding mode theory is applied to the observer design in order to overcome model uncertainties. The injector model and observer are evaluated through the injector experiments. The simulation results of the injector model are in good agreement with the experimental data. The sliding mode observer can effectively estimate the injection timing and the injection rate of the injector.