• Journal of Advanced Marine Engineering and Technology
• /
• 제37권1호
• /
• pp.53-58
• /
• 2013

비에스테르화 대두유의 활용 가능성을 평가하기 위해 현재 대부분의 디젤 자동차에 채택되어 있는 전자 제어 분사식 과급디젤기관에 경유, 에스테르화 바이오 디젤유 5% 및 비에스테르화 대두유 5% 혼합유를 사용하여 성능 실험을 실시하였다. 그 결과, 에스테르화 바이오 디젤유 5%와 비에스테르화 대두유 5%의 연소성능이 대부분 비슷하지만 NOx는 비에스테르화한 것이 더 적게 배출되었고 이는 Fuel NO에 의한 것을 밝혔다.

• 한국자동차공학회논문집
• /
• 제22권3호
• /
• pp.105-113
• /
• 2014

Spray and combustion process with waste cooking oil (WCO) biodiesel and commercial diesel were analyzed in an optically-accessible single-cylinder compression ignition diesel engine equipped with a high pressure common-rail injection system. Direct imaging method was applied to investigate spray and combustion characteristics. From the mie-scattering results, it was verified that WCO biodiesel had a longer injection delay compared to diesel. Spray tip penetration length of WCO biodiesel was longer and spray angle was narrower than those of diesel due to poor atomization characteristics. In terms of combustion, WCO biodiesel showed later start of combustion, while flame was vanished more rapidly. Analysis of flame luminosity showed that WCO biodiesel combustion had lower intensity and lasted for shorter duration.

• 한국자동차공학회논문집
• /
• 제17권1호
• /
• pp.105-113
• /
• 2009

The performance of a direct-injection type diesel engine often depends on the strength of swirl or squish, shape of combustion chamber, the number of nozzle holes, etc. This is of course because the combustion in the cylinder was affected by the mixture formation process. In this paper, combustion process of biodiesel fuel was studied by employing the piston which has several grooves with inclined plane on the piston crown to generate swirl during the compression stroke in the cylinder in order to improve the atomization of high viscosity fuel such as biodiesel fuel and toroidal type piston generally used in high speed diesel engine. To take a photograph of flame, single cylinder, four stroke diesel engine was remodeled into two stroke visible engine and high speed video camera was used. The results obtained are summarized as follows; (1) In the case of toroidal piston, when biodiesel fuel was supplied to plunger type injection system which has very low injection pressure as compared with common-rail injection system, the flame propagation speed was slowed and the maximum combustion pressure became lower. These phenomena became further aggravated as the fuel viscosity gets higher. (2) In the case of swirl groove piston, early stage of combustion such as rapid ignition timing and flame propagation was activated by intensifying the air flow in the cylinder. (3) Combustion process of biodiesel fuel was improved by the reason mentioned in paragraph (2) above. Consequently, the swirl grooves would also function to improve the combustion of high viscosity fuel.

• 한국자동차공학회논문집
• /
• 제19권5호
• /
• pp.14-21
• /
• 2011

In diesel engines, accurate EGR control is important due to its effect on nitrogen oxide and particulate matter emissions. Conventional EGR control system comprises a PI feedback controller for tracking target air mass flow and a feedforward controller for fast response. Physically, the EGR flow is affected by EGR valve lift and thermodynamic properties of the EGR path, such as pressures and temperatures. However, the conventional feedforward control output is indirectly derived from engine operating conditions, such as engine rotational speed and fuel injection quantity. Accordingly, the conventional feedforward control action counteracts the feedback controller in certain operating conditions. In order to improve this disadvantage, in this study, we proposed feedforward EGR control algorithm based on a physical model of the EGR system. The proposed EGR control strategy was validated with a 3.0 liter common rail direct injection diesel engine equipped with a DC motor type EGR valve.

• 한국자동차공학회논문집
• /
• 제20권2호
• /
• pp.123-134
• /
• 2012

A typical cooling system of an engine relies on a water pump that circulates the coolant through the system. The pump is typically driven by the crankshaft through a mechanical link with engine starting. In order to reduce the friction and warm-up time of an engine, the clutch-type water pump (CWP) was applied in 2.0 liter diesel vehicle. The clutch-type water pump can force cooling water to supply into an engine by the operation of an electromagnetic clutch equipped as the inner part of pump system. The onset of CWP is decided by temperature of cooling water and engine oil. And, the control logic for an optimal operation of the clutch-type water pump was developed and applied in engine and vehicle tests. In this study, the warm-up time was measured with the conventional water pump and clutch-type water pump in engine tests. And the emission and the fuel consumption were evaluated under NEDC mode in vehicle tests. Also, tests were carried out for the various temperature conditions starting the operation of CWP. From the results of the study, the application of CWP can improve the fuel consumption and $CO_2$ reduction by about 3%.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 춘계학술대회 초록집
• /
• pp.220.2-220.2
• /
• 2011

Biodiesel and biodiesel blend fuel are receiving increasing attention as alternative fuels for diesel engines without substantial modifications. Biodiesel fuels and blending have been widely studied and applied in diesel engine because of biodiesel's lower sulfur, lower aromatic hydrocarbon and higher oxygen content. Biodiesels have the potential to be oxidized in different condition. It has reported that oxidation deterioration of biodiesel is different in the condition of storage and oxidation causes chemical property change of methyl esters. Sunlight intensity, temperature, material of container and contact surface with oxygen are key dominant factors accelerating oxidation deterioration. In this study, we chose temperature among key oxidation conditions and metal container filled with biodiesel was heated at about $110^{\circ}C$ for 10 days in order to accelerate oxidation deterioration. To better understand the effect of biodiesel blends on emission, steady state tests were conducted on a heavy duty diesel engine. The engine was fueled with Ultra Low Sulphur Diesel(ULSD), a blend of 10% and 20%(BD10, BD20) on volumetric basis, equipped with a common rail direct injection system and turbocharger, lives up to the requirements of EURO 3. The experimental results show that the blend fuel of normal biodiesel with BD10 and BD20 increased NOx. The result of PM was similar to diesel fuel on BD10, but the result of PM on BD20 was increased about 63% more than its of diesel. The blend fuel of Oxidation biodiesel with BD10 and BD20 increased NOx as the results of normal biodiesel. But PM was all increased on BD10 and BD20. Especially THC was extremely increased when test fuel contains biodiesel about 140% more than its of diesel. Through this study, we knew that oxidation deterioration of biodiesel affects emission of diesel engine.

• 전기전자학회논문지
• /
• 제18권1호
• /
• pp.152-158
• /
• 2014

본 연구에서는 저온유동성 성능검사 시스템 구현을 통해 디젤 차량용 통합형 연료히터의 성능을 평가한다. 저온 유동성 시험장치에서 $+20{\sim}-30^{\circ}C$ 온도범위에 따라 분리형과 통합형 연료히터 성능을 비교하고, 필터 전후에 따라 유압과 시동시간, 히터의 소모전력을 측정한다. 이때 다양한 종류의 필터면적을 사용함으로써 통합형 연료히터와 분리형을 비교한 결과 시동 시간이 23% 향상되었고, 저온시동성능은 19% 정도 향상된다.

• 대한기계학회논문집B
• /
• 제35권12호
• /
• pp.1375-1381
• /
• 2011

커먼레일 분사 시스템이 장착된 대형 단기통 가시화 엔진에서 디젤과 JP-8 의 연소 및 배기 특성을 분석하였다. 두 연료 적용 시, 배기 배출 경향을 분석하기 위해 직접 화염가시화와 이색법을 적용하였다. 연소 과정은 직접 화염 가시화로부터 화염 강도 분석을 통해 이루어 졌다. 이색법 결과는 화염 온도 및 KL 값을 도출하여 분석을 하였다. 직접 화염 가시화 결과, JP-8 연소 시, 점화 지연 기간이 길며, 디젤 연소에 비해 화염이 빠르게 소멸되는 것을 확인하였다. 화염 강도 분석을 통해 디젤 연소의 경우, 연소 전 기간에 걸쳐 높은 화염 강도 수준을 유지하며 화염 지속 기간이 긴 것을 알 수 있었다. 이색법 결과를 통해, JP-8 연소의 경우, 국부적으로 고온의 화염 면이 더 많이 분포하는 것을 확인하였으며, 이는 $NO_x$가 더 많이 배출된 경향을 설명해준다. 또한 KL 치 분석 결과, JP-8 연소 시 낮은 수준의 KL 값이 더 고르게 분포하는 것을 알 수 있었으며, 이는 JP-8 연소 시 스모크 가 덜 배출된 결과를 뒷받침 해준다.

• 대한기계학회논문집B
• /
• 제36권2호
• /
• pp.217-224
• /
• 2012

비도로용 차량의 경우 대부분 디젤엔진을 사용하여 엔진의 특성상 PM과 NOx의 배출이 많은 단점이 있다. 승용 및 상용 디젤 차량의 경우 CRDI 및 후처리 장치를 적용하였고 후처리 장치로 DOC/DPF를 장착함으로써 PM은 약 90% 이상 저감 가능하다. 상반관계인 NOx는 EGR 사용을 통해 1차적으로 NOx 배출량을 감소시키고 LNT, LNC, Urea-SCR 등의 DeNOx 시스템으로 NOx의 배출량을 보다 현저히 저감시켜 배기규제를 만족시키고 있다. 본 연구에서는 tier 4 interim 배기규제를 만족하기 위해 56kW급 오프로드 차량으로 연구를 진행하였다. NOx의 감소를 위해 WGT와 전자 제어방식의 HPL EGR 시스템을 적용하였고 CO와 THC, PM 배출가스를 줄이기 위해 DOC와 DPF를 사용하였다. EGR 시스템을 적용하기 위해 각 조건에 대한 기본 실험을 실시하여 EGR map을 작성하였다. 작성된 map을 NRTC 모드에서 시험하여 map의 적용성을 검증하고 tier 4 interim 배기규제 만족여부를 파악하였다.