• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.6
• /
• pp.491-497
• /
• 2012

A hull-form for a 32,000G/T class Ro-Pax ferry has developed in accordance with a need of ferry operators to reduce fuel oil consumption(FOC) due to the drastic increase in oil prices recently and strengthening of environmental rules and regulations such as CO2 emission. A twin-skeg type is applied as the hull-form in lieu of an open-shaft type in order to improve propulsion performance. In order to achieve this object, flow control devices are installed to reduce a propeller induced vibration which is a main reason to obstruct the application of twin-skeg type passenger vessels owing to an uncomfortable vibration level. Numerical simulation by using an in-house code and a commercial code (Fluent) has performed to find out an optimum design of the flow control devices and to check an improvement in cavity volume. Model tests in Samsung Ship Model Basin are carried out to evaluate propulsion performance with the developed twin-skeg type hull and a reference hull of open-shaft type. In conclusion, it is shown that the twin-skeg type hull is better than the open-shaft in FOC by around 7% and in cavity volume by 20% as well.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.6 no.1
• /
• pp.25-34
• /
• 1969

From viewpoints of over-all ship economy the straight framed V-bottom hull forms with chines are considered to be attractive even for usual commercial vessels, because increments of resistance over that of round hull forms, if any, can be well compensated with reduction in construction cost.[1] To investigate the influences of both prismatic coefficient and chine elevation on resistance performance, three models of straight-framed V-bottom hull forms which are similar to Prof. C. Ridgely-Nevitt's W-18, W-8, and W-20[2],[3] in size and hull form coefficients were tested at the SNU Ship Model Towing Tank for resistance measurements. They are of Cp=0.60, 0.65 and 0.70 and of ${\Delta}/(0.01L)^3=300$. Influence of variation of chine elevation on resistance performance were observed with the test results obtained at normal condition, and at the trimed by the stern by 2% and 4% of $L_{bp}$ at normal condition under same displacement. The hull form characteristics are shown in Table 1, and in Fig. 1, 2, 3, 4 and 5. The test results are shown in Fig 8, 9 and 10 in the form of Cr vs. $V/\sqrt{L}$ curves taking Cp as a parameter for normal condition, trim by the stern in 2% and 4% $L_{bp}$ at normal condition , respectively. Cr vs. $V/\sqrt{L}$ curves taking trim condition as a parameter are also shown in Fig 11, 12 and 13 for Cp=0.60 and 0.70, respectively. The best and the worst trim condition at given $V/\sqrt{L}$ in viewpoint of Cr are plotted for each Cp-value as shown in Fig 14, 15 and 16. From the above results the following conclusions are derived: (1) In general, the resistance performance of the straight-framed V-bottom hull forms are not inferior to those of round hull forms. At a certain range of $V/\sqrt{L}$ the former gives less resistance than the latter. (2) Regarding influences of Cp on Cr, it is observed that, at $V/\sqrt{L}$ less than about 0.925, the greater Cp-value gives the more increment of Cr, and that, at $V/\sqrt{L}$ greater than about 0.925 the smaller Cp-value gives the more increment of Cr. It is also noteworthy that the model of Cp=0.70 has remarkable hump on Cr vs. $V/\sqrt{L}$ curve between $V/\sqrt{L}=0.80$ and 0.90. (3) For higher speed within the test range, the chine elevation having the steeper slope around bow and the easier slope around amidship and stern, refered to watering, give the better results in resistance performance. (4) Assuming the chine elevations adopted for the tested models were not of the best, we would expect further improvement of resistance performance for such form. Hence, a systematic study on chine elevation is very disirable to prepare design data of general purpose for the such hull forms.

• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.2
• /
• pp.79-89
• /
• 2004

The viscous free surface flow around KRISO container ship (KCS) is computed using the finite volume based multi block RANS code, WAVIS developed at KRISO. The free surface is captured with the Level-Set method and the realizable k-$\varepsilon$ model is employed for turbulence closure. The computations are carried out at model scale. For accurate free surface solution and its stable convergence the computations are performed with a suitable grid refinement around the free surface by applying an implicit discretization method based on a finite volume method to the Level-Set formulation. In all computational cases the numerical results agree well with experimental measurements.

• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.1
• /
• pp.15-22
• /
• 2004

Twin-skeg type stern shapes are recently adopted for very large commercial ships. However it is difficult to apply a CFD system to a hull form having twin-skeg, since grid topology around a twin-skeg type stern is more complicated than that of a conventional single-screw ship, or of an open-shaft type twin-screw ship with center-skeg. In the present study a surface mesh generator and a multi-block field grid generation program have been developed for twin-skeg type stern. Furthermore, multi-block flow solvers are utilized for potential and viscous flow analysis around a twin-skeg type stern The present computational system is applied to a 15,000TEU container ship with twin-skeg to prove the applicability. Wave profiles and wake distribution are calculated using the developed flow analysis tools and the results are compared with towing tank measurements.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.4
• /
• pp.432-438
• /
• 2017

The primary objective of the current work was to develop a standardized retrofit hull form capable of saving energy based on existing vessels. The bow shape of existing vessels was investigated, giving consideration to design draft and speed. Resistance performances were assessed for existing vessels according to operating conditions. Commercial CFD codes and model test materials were used for assessment of effective power. Three retrofit hull forms with minimum resistance were selected given real operating conditions. These vessels were named after customized ready-made hull forms to enable ship owners to make easier choices. The effective power of each vessel was estimated under real operating conditions. Subjects were operated with the lowest draft, and performance for retrofit No. 3 showed an 11-16% improvement in effective power at low speed ranges of 16-18 knots compared to existing vessels. When operated with a middle draft, performance for retrofit No. 3 showed a 6-11% improvement in effective power at low speed ranges compared to existing vessels. When operated with the highest draft, performance for all vessels showed little difference in effective power.

• Journal of Ocean Engineering and Technology
• /
• v.16 no.3
• /
• pp.65-71
• /
• 2002

From the definition of the cruise ship mission based on the investigation of the customer needs and statistical estimates and to design of the residence area of the cruise ship, in this study a conceptual design of the traditional ship parts (the lower hull) was carried out. for the light weight estimation of the cruise ship, several methods that have been used for commercial ships were evaluated to adapt for the cruise ship, the main particulars of the ship were determined with the light weight estimation and the assumed dead weight. From these main particulars of the ship, the hull form was developed with CFD verification and the general arrangement for the lower hull was achieved. For several loading conditions the intact stability of ship was checked.

• Journal of the Society of Naval Architects of Korea
• /
• v.46 no.2
• /
• pp.97-104
• /
• 2009

Ever increasing fuel prices, almost doubled in the last three years, and global pressure to reduce their environmental impact have been enforcing commercial vessel operators and designers to re-assess current vessel designs with emphasis on their propulsion systems and operational practices. In this paper the "Inclined Keel Hull (IKH)" concept, which facilitates to use larger propeller diameter in combination with lower shaft speed rates and hence better transport efficiency, is explored for a modern 3600 TEU container vessel with the aim of fitting an 13 % larger diameter propeller (and hence resulting 20% lower rpm) to gain further power saving over the similar size basis container ship with conventional "level keel" configuration. It appears that successful application of the "inclined keel Hull" concept is a fine balance amongst the maximum gain in propulsive efficiency, minimum increase in hull resistance and satisfaction of other naval architectural and operational requirements. In order to make the concept economically more viable, this paper concentrates on the fore body design with the possible combination of increase of volume in its fore body to recover the expected volume loss in the aft body due to the space for larger propeller and its low wave-making resistance to minimize the efficiency loss using a well-established optimization software.

• Journal of Navigation and Port Research
• /
• v.37 no.5
• /
• pp.481-486
• /
• 2013

In this study, a commercial seakeeping program Seakeeper, integrated into Maxsurf, which is based on the linear strip theory was employed to compare the effect of bulbous bow (with/without) on motion response characteristics in a 18-meter catamaran. The seakeeping analyses were conducted at several Beaufort wind conditions such as scale No. 3 ($\bar{T}=2.98s$, $H_{1/3}$ =0.6m), No. 4 ($\bar{T}=3.85s$, $H_{1/3}$ =1m) and No. 5 ($\bar{T}=5.44$, $H_{1/3}$ =2m) based on ITTC wave spectrum. Pitch motion response spectrum was calculated at Head sea, Head & bow sea and Beam sea as encounter angles. Hull form of a catamaran with bulb showed the maximum 20% decrease of pitch motion response as compared to that of hull form without bulb.

• Journal of Ship and Ocean Technology
• /
• v.9 no.3
• /
• pp.23-32
• /
• 2005

Ship STEP(Standard for the Exchange of Product Model Data) which is composed of AP 215 (Ship Arrangement), AP 216(Ship Hull Form), AP 218 (Ship Structure), has been developed more than last 10 years and it is now at the stage just before IS(International Standard). It is expected that ship STEP would be used for the seamless data exchange among various CAD/CAM/CAE systems of shipbuilding process. In this paper the huge and complicated data structure of ship STEP is briefly reviewed at the level of ARM(Application Reference Model) and some abstract test cases which will be included as part of the standards are introduced. Basically ship STEP has common data model to be used without losing compatibility among those three different ship AP's, and it is defined as the modeling framework. Typical cases of data exchange during shipbuilding process, such as hull form data exchange between design office and model basin, midship structure data between shipbuilding yard and classification society are reviewed and STEP physical data are generated using commercial geometric modeling kernel. Test cases of ship arrangement at initial design stage and hydrodynamic data of crude oil carrier are also included.

• Journal of Ocean Engineering and Technology
• /
• v.29 no.3
• /
• pp.224-230
• /
• 2015

Vessels are traditionally optimized for a single condition, normally the contract speed at the design draft. The actual operating conditions quite often differ significantly. At other speed and draft combinations, adjusting the trim can often be used to reduce the hull resistance. Changing the trim is easily done by shifting ballast water. There are several ways to assess the effect of the trim on the hull resistance and fuel consumption, including in-service measurements, model tests, and CFD. In this paper, CFD is employed for the assessment of the resistance performance according to the trim conditions. The commercial CFD code of the STAR-CCM+ is utilized to evaluate the ship’s resistance performance on a 6,800 TEU container ship. To validate of the effectiveness of STAR-CCM+, the experimental result of the KCS hull form is compared with the result from STAR-CCM+. It is found that the total resistance of the 6,8000 TEU container ship was reduced by 2.6% in the case of a 1-m trim by head at 18knots.