• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.48 no.6
• /
• pp.71-81
• /
• 2011

Unlike a typical internal combustion engine vehicle, the powertrain system of the pure electric vehicle, consisting of battery, inverter and motor, has direct effects on the vehicle performance and dynamics. Then, the specific modeling of such complex electro-mechanical components enables the insight into the longitudinal dynamic outputs of the vehicle and analysis of entire powertrain systems. This paper presents the dynamic model of electric vehicle powertrain systems based on theoretical approaches to predict and analyze the final output performance of electric vehicles. Additionally, the correlations between electric input signals and the final output of the mechanical system are mathematically derived. The proposed model for powertrain dynamics of electric vehicle systems are validated with a reference electric vehicle model using generic simulation platform based on Matlab/Simulink software. Consequently, the dynamic analysis results are compared with electric vehicle simulation model in some parameters such as vehicle speed/acceleration, and propulsion forces.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.3
• /
• pp.18-24
• /
• 2005

To evaluate structural safety factor of the jet vane for the thrust deflection system under the dynamic pressure and very high temperature(2700$^{\circ}C$ ) of the combustion gas flow, the high temperature tension tests of refractory metals and 3-D nonlinear numerical simulations are performed. Through the analysis of high temperature structure behavior for jet vane, the structure safety of jet vane is evaluated, and numerical results are compared with static ground tests of jet vanes. It has been found that most of structural and thermal loading is concentrated on the vane shaft which worked as safe under 1400$^{\circ}C$. From the comparison of static ground tests and numerical results, the evaluation criterion using the vane load and shaft displacement is more useful to estimate the structural safety than using the equivalent stress.

• Journal of Power System Engineering
• /
• v.13 no.5
• /
• pp.52-58
• /
• 2009

A gas turbine consists of an upstream compressor and a downstream turbine with a combustion chamber, and also the compressor and the turbine are generally coupled using a single shaft. Many casing bolts are used to assemble two horizontally separated casings, the gas turbine casing and the compressor casing, in both of axial and vertical directions. Because drilled holes for casing bolts in vertical direction are often too close to drilled holes for casing bolts in axial direction, one can observe cracks in the area frequently during operations of a gas turbine. In this study of the root cause analysis for the cracking initiating from the drilled holes of the casings of a gas turbine, the finite element analysis(FEA) was applied to evaluate the thermal and mechanical characteristics of the casings. By applying the field operation data recorded from combined cycle power plants for FEA, thermal and thermo-mechanical characteristics of a gas turbine are analyzed. The crack is initiated at the geometrical weak point, but it is found that the maximum stress is relieved when the same type of cracks is introduced on purpose during FEA. So, it is verified that the local fracture could be delayed by machining the same type of defects near the hole for casing flange bolts of the gas turbine, where the crack is initiated.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.10
• /
• pp.801-807
• /
• 2020

Opening characteristics of a main oxidizer shut-off valve at different valve inlet pressures have been experimentally investigated. The pilot pressure at the moment of the valve opening increases linearly with increasing the valve inlet pressure and the increased pilot pressure reduces the valve travel time. As the pilot pressure increases at the moment of valve opening, the time to start opening the valve is delayed resulting in increasing the valve opening time. With the increment of the valve inlet pressure, the valve opening time is mainly determined by the time required for the pilot pressure to start opening the valve. Therefore the design of a pilot gas supply system can readily control the valve inlet pressure at the valve opening as well as the amount of oxidizer supplied to a combustion chamber during the engine startup.

• Proceedings of the Korea Society of Environmental Toocicology Conference
• /
• 2002.10a
• /
• pp.171-171
• /
• 2002

Recent industrial society has human widely exposed to PAHs that are comming from the incomplete combustion of organic material as widerspread environmetal contaminants. Biological activities of PAHs are not known although PAHs are considered as carcinogens. PAHs in the mammalian cells affect CYP1A1 gene expression as well as other phase II drug metabolizing enzymes as UDPGT, NMOR etc. The mechanism of action of PAHs has been studied extensively, however it is not clear how PAHs turn on CYP1A1 in human breast cancer. Our labolatory have been studied the effect of PAHs in the human breast cancer cell lind MCF7. In this study, we examined the ZR-75-1 human breast cancer cells as a new system to evaluate bioactivity of PAHs. ZR-75-1 human breast cancer cell line has been estabilished from the breast cnacer patient, has estrogen receptors and progesteron receptors. We have been able to estbilish long term culture system of this cells then used for the study to observe the effect of PAHs. We demonstrate that PAHs induced the transcription of an aryl hydrocarbon-responsive reporter vector containing the CYP1A1 promoter and 7-ethoxyresolufin O-deethylase(EROD) activity of CYP1A1 enzyme in a concentration-dependant manner. RT-PCR analysises indicated that PAHs significantly up-regulate the constitutive level of CYP1A1 mRNA. Apparently, ZR-75-1 cells have Aryl hydrocarbon recetors, therefore it would be good experimental tool to study the cross-talk between PAHs and steroid actions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.2
• /
• pp.7-13
• /
• 2010

To satisfy the needs on fuel economy and engine performance, continuous variable valve lift systems are applying to engines. In the CVVL system, fuel economy can be improved by reducing pumping loss during the induction process, and engine performance can be also improved by controlling volumetric efficiency and the residual gas fraction. Because the residual gas fraction directly affects volumetric efficiency, engine performance, combustion efficiency and emissions in SI engines, controlling residual gas fraction is one of the important things in engine development process. This analysis investigates the residual gas fraction and volumetric efficiency with changes of intake valve lifts and intake valve timings. In this study, unsteady state solutions were solved during exhaust and induction processes. Results show variation of the residual gas fraction and volumetric efficiency by changing intake valve timing and lift. Decreasing intake valve lift leads to increase the residual gas fraction and to decrease volumetric efficiency.

• Tribology and Lubricants
• /
• v.28 no.6
• /
• pp.315-320
• /
• 2012

For proper functioning, general machines usually need lubricant oil as a cooling, cleaning, and sealing agent at points of mechanical contact. The quality of lubricant oil can deteriorate during operation owing to various causes such as high temperature, combustion products and extraneous impurities. In this study, a heavy load stopped during operation, and the oil was analyzed to check whether any impurities were added. Extraction using acetonitrile followed by reaction with BSTFA(bistrimethylsilyl trifluoroacetamide) showed that, trimethylsilylated ethylene glycol was present in the lubricant oil. To quantify the ethylene glycol in the oil, deuterium-substituted ethylene glycol, which acted as an internal standard, was added to the sample and then extracted with the solvent. Next, the extract was reacted with the derivatizing agent(BSTFA) and then analyzed with GC/MS. The detection limit of this method was found to be $0.5{\mu}g/g$ and the recovery of oil containing $20,000{\mu}g/g$ of ethylene glycol was measured to be 94.8%. A damaged O-ring and eroded cylinder liner were found during the overhaul, which implied the leakage of coolant containing ethylene glycol into the lubricating system. The erosion of the cylinder liner was assumed to be due to cavitation of the coolant in the cooling system.

• Journal of Korean Society on Water Environment
• /
• v.36 no.1
• /
• pp.55-68
• /
• 2020

Because of the intensified environmental problems such as climate change and resource depletion, sewage treatment technology focused on energy management has recently attracted attention. The conversion of primary sludge from the primary sedimentation tank and excessive sludge from the secondary sedimentation tank into biogas is the key to energy-positive sewage treatment. In particular, the primary sedimentation tanks recover enriched biodegradable organic matter and anaerobic digestion process produces methane from the organic wastes for energy production. Such technologies for minimizing oxygen demand are leading the innovation regarding sewage treatment plants. However, sewage treatment facilities in Korea lack core technology and operational know-how. Actually, the energy potential of sewage is higher than sewage treatment energy consumption in the sewage treatment, but current processes are not adequately efficient in energy recovery. To improve this, it is possible to apply chemically enhanced primary treatment (CEPT), high-rate activated sludge (HRAS), and anaerobic membrane bioreactor (AnMBR) to the primary sedimentation tank. To maximize the methane production of sewage treatment plants, organic wastes such as food waste and livestock manure can be digested. Additionally, mechanical pretreatment, thermal hydrolysis, and chemical pretreatment would enhance the methane conversion of organic waste. Power generation systems based on internal combustion engines are susceptible to heat source losses, requiring breakthrough energy conversion systems such as fuel cells. To realize the energy positive sewage treatment plant, primary organic matter recovery from sewage, biogas pretreatment, and co-digestion should be optimized in the energy management system based on the knowledge-based operation.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.4
• /
• pp.333-342
• /
• 2016

Liquid rocket propulsion is a system that produces required thrust for satellites and space launch vehicles by using chemical reactions of a liquid fuel and a liquid oxidizer. Monomethylhydrazine/dinitrogen tetroxide, liquid hydrogen/liquid oxygen and RP-1/liquid oxygen are typical combinations of liquid propellants commonly used for the liquid rocket propulsion system. The objective of the present study is to investigate useful design and performance data of liquid rocket engine by conducting a numerical analysis of thermochemical reactions of liquid rocket propellants. For this, final products and chemical compositions of three liquid propellant combinations are calculated using equilibrium constants of major elementary equilibrium reactions when reactants remain in chemical equilibrium state after combustion process. In addition, flame temperature and specific impulse are estimated.

• Korean Chemical Engineering Research
• /
• v.46 no.6
• /
• pp.1057-1062
• /
• 2008

To overcome disadvantages of conventional two interconnected fluidized beds system, a novel two-interconnected fluidized bed process has been adopted to 3kW chemical-looping combustor. This system has two bubbling beds, solid injection nozzles, solid conveying lines, and downcomers. In this study, effects of operating variables such as gas velocity through the solid injection nozzle, fluidizing velocity, solid height, geometry of solid intake hole, bed temperature on solid circulation rate have been investigated in a 3kW chemical-looping combustor. The solid circulation rate increased as the solid height and the opening area of solid intake holes increased. The effect of the fluidizing velocity and the bed temperature were negligible. Moreover, long-term operation of continuous solid circulation up to 50 hours has been performed to check feasibility of stable operation. The pressure drop profiles in the bubbling beds and the downcomers were maintained steadily and solid circulation was smooth and stable.