• 한국표면공학회지
• /
• 제25권5호
• /
• pp.215-221
• /
• 1992

This research is aimed at developing(110) preferred TiS2 cathode films and glass typed solid electro-lytes which have high ionic migrations and low electron conductivities for thin secondary solid batteries. To obtain preferred oriented TiS2 thin films on a substrate by CVD method using TiCl4 and H2S gases three factors of heating temperature, inner pressure of furnace and TiCl4/H2S gas mole fraction were ex-amined systematically. To obtain solid films of Li2O-B2O3-SiO2 electrolytes by r.f. sputtering for thin proto-type batteries of Li/Li2O-B2O3-SiO2TiS2, sputtering conditions were examined. TiS2 cathode films showed columnar structure, namely c axis oriented parallely. At low pressure of reaction chamber and low heating temperature, surface of smooth TiS2 films couldd be obtained. Ionic conductivity of Li2O-B2O3-SiO2 films manufactured by r.f. magnetron sputtering were 3$\times$10-7$\Omega$-1cm-1 and electron conductivities were 10-11$\Omega$-1cm-1. Open cell voltage of thin lithium batteries were 2.32V with a designed prototype cell.

• 한국표면공학회지
• /
• 제18권3호
• /
• pp.105-115
• /
• 1985

Lead-tin-copper ternary alloy electrodeposition is conducted onto the inner bore surface of plain bearings as an overlay in order to investigate the effect of slot width, current density and fluoboric acid concentration on the uniformity of overlay. The thickness of overlay is analyzed by means of current distribution resulting from the overvoltage of plating bath and the apparent distance between cathode and anode. The result demonstrate that the uniformity of overlay is remarkably dependent of the slot size and current density, but has little bearing on the fluoboric acid concentration over 100g/L. This present study indicates that uniform overlay is obtainable within the tolerable thickness of ${\pm}2{\mu}m$ by using the slot width of 22mm. The surface morphology examination also shows the important role of concentration polarization of the micro-uniformity of overlay. The micro-uniformity has improved at the low concentration polarization which resulted from operating at the low current density and high fluoboric acid concentration. The surface morphology of deposits exhibits the vivid pyramid crystalline in the plating condition of low concentration polarizatio and all deposits have columnar structure parallel to the applied electric field regardless of the electroplating condition used.

• 한국표면공학회지
• /
• 제45권3호
• /
• pp.123-129
• /
• 2012

Nanocrystalline CrN coatings were fabricated by DC and ICP (inductively coupled plasma) assisted magnetron sputtering techniques. The effect of ICP power, ranging from 0 to 500 W, on coating microstructure, preferred orientation mechanical properties were systematically investigated with HR-XRD, SEM, AFM and nanoindentation. The results show that ICP power has an significant influence on coating microstructure and mechanical properties of CrN coatings. With the increasing of ICP power, coating microstructure evolves from the columnar structure of DC process to a highly dense one. Grain size of CrN coatings were decreased from 11.7 nm to 6.6 nm with increase of ICP power. The maximum nanohardness of 23.0 GPa was obtained for the coatings deposited at ICP power of 500 W. Preferred orientation in CrN coatings also vary with ICP power, exerting an effective influence on film nanohardness.

• Bulletin of the Korean Chemical Society
• /
• 제18권1호
• /
• pp.56-61
• /
• 1997

Lead zirconate titanate (PZT) thin fills were deposited onto the Pt/Ti/SiO2/Si substrate by the pulsed laser deposition with the second harmonic wavelength (532 nm) of Nd:YAG laser. In order to determine the optimum conditions for the film deposition, the phase of the films were investigated as functions of ambient oxygen pressure, substrate temperature, and laser fluence. Also the chemical composition analysis was conducted for the PZT films deposited under various ambient oxygen pressure. When the distance between substrate and bulk PZT target is set to 20 mm, the optimum conditions have been determined to be 3 torr of oxygen pressure, 1.5 J/cm2 of laser fluence, and 823-848(±10) K range of substrate temperature. At these conditions, perovskite phase PZT films were obtained on platinized silicon. The chemical composition of the films is very similar to that of PZT bulk target. The physical structure of the deposited films analyzed by scanning electron microscopy shows a columnar morphology perpendicular to the substrate surface. Capacitance-Voltage hysteresis loop measurements show also a typical characteristics of ferroelectric thin film. The dielectric constant is found to be 528 for the 0.48 μm thickness of PZT thin film.

• 한국표면공학회지
• /
• 제54권3호
• /
• pp.139-143
• /
• 2021

Cr-Al-N coatings were deposited onto WC-Co substrates using a cathodic arc evaporation (CAE) system. CAE technique is recognized to be a very useful process for hard coatings because it has many advantages such as high packing density and good adhesion to metallic substrates. In this study, the influence of deposition temperature as a key process parameter on film growth behavior and mechanical properties of Cr-Al-N coatings were systematically investigated and correlated with microstructural changes. From various analyses, the Cr-Al-N coatings prepared at deposition temperature of 450℃ in the CAE process showed excellent mechanical properties with higher deposition rate. The Cr-Al-N coatings with deposition temperature around 450℃ exhibited the highest hardness of about 35 GPa and elastic modulus of 442 GPa. The resistance to elastic strain to failure (H/E ratio) and the index of plastic deformation (H³/E² ratio) were also good values of 0.079 and 0.221 GPa, respectively, at the deposition temperature of 450℃. Based on the XRD, SEM and TEM analyses, the Cr-Al-N coatings exhibited a dense columnar structure with f.c.c. (Cr,Al)N multi-oriented phases in which crystallites showed irregular shapes (50~100nm in size) with many edge dislocations and lattice mismatches.

• Applied Microscopy
• /
• 제50권
• /
• pp.18.1-18.7
• /
• 2020

The olfactory anatomy and histology of Lethenteron reissneri were researched using a stereo microscope, a light microscope, and a scanning electron microscope. As in other lampreys, it shows same characters as follows: i) a single olfactory organ, ii) a single tubular nostril, iii) a single olfactory chamber with gourd-like form, iv) a nasal valve, v) a nasopharyngeal pouch, vi) a sensory epithelium (SE) of continuous distribution, vii) a supporting cells with numerous long cilia, viii) an accessory olfactory organ. However, the description of a pseudostratified columnar layer in the SE and Non SE is a first record, not reported in sea lamprey Petromyzon marinus. In particular, both 19 to 20 lamellae in number and olfactory receptor neuron's quarter ciliary length of the knob diameter differ from those of P. marinus. From these results, it might be considered that the olfactory organ of L. reissneri shows well adaptive structure of a primitive fish to slow flowing water with gravel, pebbles, and sand and a hiding habit into sand bottom at daytime. The lamellar number and neuron's ciliary length may be a meaningful taxonomic character for the class Petromyzonida.

• 한국재료학회지
• /
• 제12권6호
• /
• pp.452-457
• /
• 2002

Titanium oxide films were prepared by RF reactive magnetron sputtering. The effect of sputtering conditions on structural and optical properties was investigated systemically as a function of sputtering pressure(5~20 mTorr) and $O_2/Ar$ flow ratio(0.08~0.4). The results of the X-ray diffraction showed that all films had only the anatase $TiO_2$ phase. At low sputtering pressure and $O_2/Ar$ flow ratio, the films had preferred orientations along [101] and [200] directions. As the sputtering pressure and $O_2/Ar$ flow ratio increased, the intensity of the 101 and 200 diffraction peaks decreased gradually. The microstructure of the sputtered films showed the fine grain size (20nm~50nm) and columnar microcrystals perpendicular to the substrate. With increasing the sputtering pressure and decreasing $O_2/Ar$ flow ratio, the sputtered films showed the more porous columnar structure. XPS analysis showed that stoichiometric $TiO_2$ films were deposited at 7 mTorr sputtering pressure and 0.2 $O_2/Ar$ flow ratio. The results of the X-ray diffraction showed that all films had only the anatase $TiO_2$ phase. Ellipsometeric analysis showed that the refractive index increased from 2.32 to 2.46 as the sputtering pressure decreased. The packing density calculated using the refractive index varied from 0.923 to 0.976, indicating that $TiO_2$films became denser as the sputtering pressure decreased.

• 한국양식학회지
• /
• 제17권3호
• /
• pp.215-220
• /
• 2004

돌돔, Oplegnathus fasciatus의 소화관은 식도, 위, 장 및 항문이 일련의 관을 이루고 있고,전체적으로 지방 덩어리가 싸고 있다. 어체 체장에 대한 식도에서 항문까지의 소화관 길이의 비(relative length of gut: RLG)는 일반적인 잡식성 어류와 비슷한 평균 1.78 (n=30)의 값을 가진다. 식도는 근육층이 잘 발달되어 있으며, 점막주름의 상피층은 입방상피 또는 원주상피로 구성되고 상피세포 사이에는 다수의 산성 점액분비세포들이 분포하며, 상피세포의 정단부에서 미세융모의 관찰은 어렵다. 위의 근육층은 외부로부터 종주근, 환상근층으로 구성된다. 위의 점막주름은 규칙적인 형태로서 상피층에는 pit, 상피 및 위선이 아주 잘 발달되어 있으며, 점막상피 세포질의 정단부에서는 영양분 흡수계통의 물질들이 관찰된다. 50∼60개의 유문수를 가지는 돌돔 유문수의 점막상피층에서는 원주형의 상피세포와 중성의 점액분비세포들이 관찰되며, 상피세포의 정단면에는 미세융모가 발달되어 있다. 장의 점막상피층에서는 원주상피세포와 중성과 산성의 점액분비세포들이 관찰되며, 종주근층의 두께가 전장, 중장, 후장으로 갈수록 두꺼워진다. 산성의 점액분비세포의 출현빈도는 중장부에서 가장 발달된 양상을 보이며 후장부로 갈수록 감소하는 경향을 보인다.

• 한국재료학회지
• /
• 제8권4호
• /
• pp.368-374
• /
• 1998

Zr합금의 부식거동을 평가하기 위하여 여러 가지 1족 알칼리 수산화물 용액 (LiOH, NaOH, KOH, RbOH, CsOH)에서 autoclave를 이용하여 300일까지 부식시험을 실시하였다. 산화막 특성은 TEM을 이용하여 천이전과 천이후에 동일 산화막두께를 갖도록 준비된 부식시편에 대해 수행되었다. 실험결과를 고려할 때 금속이온은 부식과정에서 매우 중요한 역할을 하는 것으로 사료된다. 즉 $Li^+$가 $Zr^{4+}$ 치환하여 산소농도는 증가하고 부식은 가속되는데 산화막 내부의 barrier layer에서 $Li^-$치환이 부식을 제어하는 것으로 판단된다.동일 두께의 산화막 일지라도 산화막의 구조는 모두 다르다. 32.5mmol LiOH에서 생성된 산화막온 천이전,후에 관계 없이 많은 기공이 함유된 등축정 구조를 갖는다. 반면에 NaOH에서 생성된 산화막은 천이전에는 주상정 구조를 갖지만 천이후에는 다공성의 등축정 구조로 바뀐다. KOH용액에서는 천이전에는 주상정과 비정질 산화막의 이중 구조를 갖지만 천이후에는 비정질 산화막은 사라직 전반적으로 주상정 구조가 형성된다. 부식거동과 산화막 관찰로부터 금속이온의 산화막내 치환이 부식속도와 산화막 미세구조를 지어한다는 것을 알 수 있었다.

• 한국표면공학회지
• /
• 제46권6호
• /
• pp.258-263
• /
• 2013

4 mol% Yttria-stabilized zirconia (4YSZ) coatings are fabricated by Air Plasma Spray (APS) and Electron Beam Physical Vapor Deposition (EB-PVD) with top coating of thermal barrier coating (TBC). NiCrAlY based bond coat is prepared as 150 ${\mu}m$ thickness by conventional APS (Air Plasma Spray) method on the NiCrCoAl alloy substrate before deposition of top coating. Each 4YSZ top coating shows different tribological behaviors based on the inherent layer structures. 4YSZ by APS which has splat-stacked structure shows lower friction coefficient but higher wear rate than 4YSZ by EB-PVD which has columnar structure. For 4YSZ by APS, such results are expected due to the sliding wear accompanied with local delamination of splats.