• YAKHAK HOEJI
• /
• v.3 no.1
• /
• pp.48-50
• /
• 1957

The micro-assay methods of vanillin have been shown quite few, though several methods have been introduced for determination. A new sensitive micro-determination of vanillin, applying the yellow color reaction of vanillin and anillin, is shown in this paper. The absorption maximum of the yellow coloring matter, 4-Oxy-3-methoxy-henzal aniline, was 435 mu. The one dimensional ascending paper chromatographic method is applyed for isolation of vanillin from the mixed sample. The microdetection of vanillin is studied only in this paper. Vanillin was detected by the yellow spot on paper trip by the coloring reagent of aniline after several hours paper strip chromatographic at the following condition; paper strip ................ 2.5 X 35cm Whatman Filter Paper No.2 developing Solvent ......... petroleum-benzene-methanol n-butanol-water coloring agent ............. aniline. The Rf-value on petroleum benzene and methanol was 0.63 and that on n-butanol and water was 0.90. The minimum detectable amount of vanillin by this method was 10 micrograms. It is recommendable, if interference substances as aromatic aldehydes present, that the application of this aniline reaction and Foline Denis reaction on the same paper chromatogram is appreciable.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.8
• /
• pp.176-182
• /
• 2018

One of the most important factor of esthetic prosthesis is the color of the teeth. Zirconia is produced in the process of design, milling, coloring, drying, and sintering. The effect of the drying degree of zirconia colorant on the color tone is examined. For the experiment, a total of 45 zirconia specimens(15 for each) were fabricated by using cad/cam system. The zirconia specimens(L block(LAZOR), Z block(Zircos-E block posterior), A block(AlphaZ)) were then subjected to zirconia sintering in accordance with the manufacturer's instructions, using a chemical coloring agent to Non-drying(0sec), intermediate (10sec), and completely dried (10min) temperature holding times. The color tone was measured using a spectrophotometer. The results were analyzed with a One-way analysis of variance and the Tukey post-hoc test (${\alpha}=.05$) The $L^*$ values of L, A specimens, $a^*$ values of A specimens, and $b^*$ values of Z specimens were not statistically different according to the degree of drying (p>0.05), While the $L^*$ value of Z specimen, $a^*$ value of L, Z specimen, $b^*$ values of L, A specimens were statistically different according to the degree of drying(p <0.05). In conclusion, the drying of zirconia colourants improves zirconia brightness and increases the optical properties of the enamel.

• Applied Microscopy
• /
• v.38 no.3
• /
• pp.159-165
• /
• 2008

Morphological and physicochemical changes of a woman's virgin hair treated with various dye depths were investigated by using scanning electron microscopy and thermal analyzer. With the hair treated with the dye of the high brightness level, the speed of weight decrease was slower than compared with thermal analysis weight of a normal hair sample. We confirmed that the moisture content and protein composition of hair were changed depending on level depth of coloring agent. Moreover oxidative residues and dye molecules penetrated into the hair cause chemical changes of hair structure. As a result, the heat reaction speed of hair treated with high level coloring agent was made slower than normal hair.

• Textile Coloration and Finishing
• /
• v.31 no.4
• /
• pp.241-248
• /
• 2019

In this study, improving the wash and rubbing fastness of a natural coloring matter from Madder extract dyed on Tencel nonwoven. The cationic finishing agent(RBP), nonionic finishing agent(HPX) and mordant(PAW) were used to improving the color fastness. The two types(exhaustion and pad-dry-cure) finishing process were investigated with various finishing agent concentration. The color strength, wash and rubbing fastness of Tencel nonwoven dyed with Madder extract have been evaluated by various dye concentration and finishing agent. The exhaustion process treated with the cationic finishing agent(RBP) was effective to improving washing and rubbing fastness.

• Journal of Wetlands Research
• /
• v.16 no.2
• /
• pp.275-280
• /
• 2014

Because ammonia in water body can cause water pollution as a result of generating ammonium ion, it is of importance in the management of water quality. This work performed to analyze the ammonium ion by measuring the color band length on the basis of modifying the indophenol method. When 1-naphthol was employed as a coloring agent, the maximum absorbance was shown near 720nm, where the proper injection was in the range of 0.5-1.5ml. About 80% of absorbance was observed after the color development was made within the 20 minutes. In the manufacturing of coloring agent, the proper concentration of NaOH was 1.5-2.5M, and the effect of pH on the color development is negligible. In addition, the color development was effectively in the region of room temperature.

• Textile Coloration and Finishing
• /
• v.24 no.4
• /
• pp.305-312
• /
• 2012

In this study, we investigated the effects of oxidative permanent hair coloring agents on the dyeability and the damage of human hair. p-phenylenediamine and toluene-2.5-diamine sulfate were used as a hair coloring agent precursers. The degree of dyeability was checked by the change of CIELAB $L^*$ value according to dyeing time. And the damage of hair was evaluated by the tensile strength and morphological change of hair in SEM. When the hair was dyed, the CIELAB $L^*$ value was decreased with dyeing time regardless of the type of precursers. But when the hair was dyed after nutritional treatment, the CIELAB $L^*$ value showed lower level. This means that the nutritional treatment covers the scale of hair and protects the hair from the chemicals.

• Journal of the Korea Concrete Institute
• /
• v.23 no.3
• /
• pp.265-272
• /
• 2011

Even though concrete is the most important material for building structures, its intrinsic gray color degrades urban esthetics. In order to improve this problem, coloring methods of mixing pigment in concrete batch and painting the surface of concrete surface have been tried. However, applications of the coloring methods in construction field are difficult due to high cost and low durability. Recently, acid stain agent is emerging as a new coloring method for concrete. It is able to apply a remarkably thin colored layer on a concrete surface from chemical reaction between acid and alkaline solutions. This study has examined the changes and variations of the surface layer of mortar specimen from chemical reaction of acid stained agents. The colors were changed into natural irregular stains according to aging. After the staining, no shape change was found from visible inspections. Microstructure of the colored surface applied with acid stained agent was much rougher than that of original mortar. When the colored layer was compared to original surface, crystals of hydrate such as $Ca(OH)_2$ and C-S-H gel were observed. Surface hardness was same or slightly higher in the colored layer. The value of pH was reduced by approximately 10%, weight contents of elements such as Ca, Si, and Al were low. In the chemical composition of the colored layer, the non-cement based elements of Mn, Cr, and Cu increased. Also, Fe and alkali elements of K and Na increased.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.24 no.3
• /
• pp.73-80
• /
• 1998

This Study was performed to get the suitable oil dispersion agent by assessment of color strength of organic pigment in non-aqueous systems. Organic pigment is used as a color expression material with other body pigments in the make-up products. But occasionally aggregation or agglomeration occurs for the lack of affinity with medium, This function is the cause of disturbing homogeneous dispersion, and then bring about an instability of products. Our study, research of dispersion mechanism between the pigment and oil phase, has been executed to solve this problem, and find a oil dispersion agent having optimum dispersion condition. Generally dispersion is related to between the solid-liquid mutual properties and electrical phenomena associated with solid-liquid interface. This factor is determined to input energy, milling time, optical properties, particle size, rheological properties, etc. Ideal dispersion state is told that coloring primary solid particle is homogeneously dispersed in medium. Good dispersed colorants are strongly and clearly appeared. We are already known that the particle size of organic pigment, chemical properties and viscosity of medium, refractive index. Consequently We determine the affinity of medium and organic pigment by measuring of color strength in the same mechanical condition. UV-VISIBLE RECORDING SPECTRO PHOTOMETER is used for measuring apparatus. We can decided the dispersion level of oil dispersion agent by measuring absorbance of color strength in the visible range that diluted medium for colloid colorant particles.

• Fashion & Textile Research Journal
• /
• v.15 no.5
• /
• pp.808-814
• /
• 2013

In this study, The mixture of three kinds of pre-treatment agents, Carboxymethyl cellulose sodium salt(CMC), Sodium alginate and Dextrin, have been prepared for the better coloration of digital textile printing. To get sharpness of outline during digital printing process, the optimal formulation is the CMC and Sodium alginate mixture 1:1 ratio by volume. Cyan, Yellow, and Black colours are excellent on the Sodium alginate mixtures. But, Magenta is excellent in the CMC and Dextrin mixture. Sharpness and printability are closely related to viscosity of the mixture. The most optimal sharpness of outline achieved with a consideration of coloring, and field operations account for production when the viscosity of the mixed pre-treatment agent approximately is 10~13 cSt. Change in shade and staining of wash fastness for all the treated samples with the mixtures rated 4-5 grade. Both dry rubbing fastness to shade change and staining are good in the treated samples, whereas wet rubbing fastness rated 2-3 grade. To improve wet rubbing fastness, the Sodium alginate and Dextrine mixture, which rated 3-4 grade for Black color, is applicable. With exception of 3 rating to black color, Light fastness is 4 rating for the remaining three colors in the regardless of treatment condition and mixing of the pre-treatment agent. Dry cleaning fastness of all samples are also 4-5 rating.

• Textile Coloration and Finishing
• /
• v.20 no.3
• /
• pp.18-24
• /
• 2008

The purpose of this study is to develop the dyeing method with dry leaves of indigo plant. Coloring matter was extracted from dry leaves of indigo plant with hot sodium hydroxide solution. The extract was reduced with sodium dithionite, and it was used for dyeing cotton fabrics under various conditions. UV-visible absorption spectra of extract, reduction rate of extracts by reducing agent, and the surface color of dyed cotton, lightfastness were examined. For the initial 20 minutes, the absorbance of indigo solution rapidly decreased. However, several hours later, the decreasing rate retarded. By repeating the dyeing process, the shade looked deeper and deeper. At $30-40^{\circ}C$, the value of K/S reached the highest point. The concentration of indigo solution in dye bath seemed to playa critical role for the reaction of the reducing agent. It was observed that the surface color of cotton fabrics was getting bluish and its degree of value and chroma seemed slightly decreased as the K/S value was increasing. The lightfastness was clearly enhanced by increasing the K/S value.