• Journal of KSNVE
• /
• v.10 no.3
• /
• pp.474-479
• /
• 2000

Piston slap is not only one of the major sources of noise and vibration in internal combustion engines but also a cause of the deterioration of engine performance. The basic mechanism associated with the piston slap seems to be quite simple but the phenomenon is in fact complicated with regard to many mechanical elements associated, First of all the impact force of piston slap must be identified to estimate engine block surface vibration, In this paper model of collision point is proposed to calculate the impact force when slap surface vibration. In this paper model of collision point is proposed to calculate the impact force when slap occurs. The parameters of the model are estimated by employing the concept of point mobility, . The predicted and experimentally observed vibration results confirm that the proposed method is practically useful.

• Journal of Auto-vehicle Safety Association
• /
• v.10 no.3
• /
• pp.7-12
• /
• 2018

The Korean New Car Assessment Program (KNCAP) is a program to evaluate the safety of automobiles. In the safety assessment method, there are frontal collision, partial frontal collision, side collision, pillar collision, and left stability in the collision safety category. Among them, Korean in-depth analysis data shows that there are a lot of side collision accidents and it is necessary to protect them. This study will analyze the side collision accident that occurred in actual traffic accident based on Korea In-Depth Accident Study (KIDAS) and investigate the effect of center airbag on passenger in under side collision. In addition, with simulated side collision scenarios in the various side impact directions, it was investigated how the center airbag affects the driver and passenger in terms of kinematic and injury levels.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.12 no.1
• /
• pp.241-257
• /
• 2020

The rapid proliferation of oil/gas drilling and wind turbine installations with jack-up rig-formed structures increases structural safety requirements, due to the greater risks of operational collisions during use of these structures. Therefore, current industrial practices and regulations have tended to increase the required accidental collision design loads (impact energies) for jack-up rigs. However, the existing simplified design approach tends to be limited to the design and prediction of local members due to the difficulty in applying the increased uniform impact energy to a brace member without regard for the member's position. It is therefore necessary to define accidental load estimation in terms of a reasonable collision scenario and its application to the structural response analysis. We found by a collision probabilistic approach that the kinetic energy ranged from a minimum of 9 MJ to a maximum 1049 MJ. Only 6% of these values are less than the 35 MJ recommendation of DNV-GL (2013). This study assumed and applied a representative design load of 196.2 MN for an impact load of 20,000 tons. Based on this design load, the detailed design of a leg structure was numerically verified via an FE analysis comprising three categories: linear analysis, buckling analysis and progressive collapse analysis. Based on the numerical results from this analysis, it was possible to predict the collapse mode and position of each member in relation to the collision load. This study provided a collision strength assessment between attendant vessels and a jack-up rig based on probabilistic collision scenarios and nonlinear structural analysis. The numerical results of this study also afforded reasonable evaluation criteria and specific evaluation procedures.

• Journal of Digital Convergence
• /
• v.16 no.9
• /
• pp.173-178
• /
• 2018

The vehicle collision speed in mid and high range can be checked by EDM(Event Driven memory) data recorded when the air bag works. But it's difficult to estimate the low speed of vehicle collision. And estimating the speed is important because the injury level can be changed by the impact speed. The study proposed an estimating algorithm by analysing the images recorded in car blackbox instrument. Low speed rear collision accidents simulated with wire winding motor for various vehicle types. The study estimated the impact speed with the ratio of the distance change between two vehicles and the length change of the number plate of front vehicle. The closer the vehicles are, the larger the plate length is. You can estimate the impact speed with the ratio. The impact speed is calculated with the initial distance for a specific length of number plate in the algorithm. The results can be applied to the linear rear collision because the angle of impact was not considered in this study.

• Nuclear Engineering and Technology
• /
• v.45 no.4
• /
• pp.553-564
• /
• 2013

This study evaluates the local damage of a turbine in an auxiliary building of a nuclear power plant due to an external impact by using the LS-DYNA finite element program. The wall of the auxiliary building is SC structure and the material of the SC wall plate is high manganese steel, which has superior ductility and energy absorbance compared to the ordinary steel used for other SC wall plates. The effects of the material of the wall, collision speed, and angle on the magnitude of the local damage were evaluated by local collision analysis. The analysis revealed that the SC wall made of manganese steel had significantly less damage than the SC wall made of ordinary steel. In conclusion, an SC wall made of manganese steel can have higher effective resistance than an SC wall made of ordinary steel against the local collision of an airplane engine or against a turbine impact.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1995.10a
• /
• pp.234-241
• /
• 1995

Offshore structures are exposed to higher probability of collision with ship because of their limited mobility. In general, the consequence of the collision is reported to be relatively small and it is desirable to consider minor collisions in the design stage. It is important to have a comprehensive understanding of the dynamic responses of a tubular, their main member, under collision to design offshore structure against possible accidents. It is needed to estimate the probable extent of damage of a tubular, depth of dent, affected by the time history of impact load in ender to design a tubular strong enough for collision. In this paper, dynamic behaviors of a tubular due to the lateral impact are investigated through the numerical simulations with hydrocode DYNA3D, a three dimensional elasto-plastic large deformation impact contact problem analyzing program.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.383-388
• /
• 2008

A modeling method for the impact analysis of plate structures employing Hertzian contact theory is presented in this paper. Since local deformation as well as bending deflection of the plate occurs due to the collision, it has to be considered for the impact analysis. When the coefficient of restitution is employed for the impact analysis, the local deformation is not considered. For more accurate and reliable impact analysis, however, the local deformation should be considered. The effects of the location of collision and the collision mass on the impact duration time and the contact force magnitude are investigated through numerical studies employing Hertzian contact theory.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.293-296
• /
• 2002

This work presents the reconstruction of impact force produced by the collision between two elastic structures. The 2-DOF impactor was designed. The shape control of impact farce using correlations of the dynamic characteristics and impact force history between two elastic structures is accomplished. The effects of the relative motion between impactor and elastic structure on the impact force shape are studied. Reconstruction characteristics of impact force in cantilever beam are reviewed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.10
• /
• pp.5963-5967
• /
• 2014

Reducing the impact of collisions of cars is a major issue for reducing the injury and death of passengers. According to the statistical data of the Road Traffic Authority, the deaths from side collision accidents caused by the collision of passenger cars is greater than the deaths from head-on collision accidents. To accommodate this, vehicle designers have added a reinforcing material called the impact frame and impact beam on the inside of the door. Many experiments are needed to develop the door impact beam. These reinforcements to develop a collision experiment is essential. Collision experiments are costly and time consuming. This study used a drop Impactor to obtain the impulse and a strain experimental device was developed for this purpose. The economic costs were reduced and the ideal experiment device configuration was determined. A comparison of the experimental results with numerical value analysis revealed $3.5{\tiimes}10-3sec$ strain ranging from $3.49{\tiimes}10-3$ to $3.99{\tiimes}10-3$.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.1
• /
• pp.175-183
• /
• 2022

The collision between a ship and bridge across a waterway may result in extremely serious consequences that may endanger the safety of life and property. Therefore, factors affecting ship bridge collision must be investigated, and the impact force should be discussed based on various collision conditions. In this study, a finite element model of ship bridge collision is established, and the peak impact force of a ship bridge collision based on 50 operating conditions combined with three input parameters, i.e., ship loading condition, ship speed, and ship bridge collision angle, is calculated via numerical simulation. Using neural network models trained with the numerical simulation results, the prediction model of the peak impact force of ship bridge collision involving an extremely short calculation time on the order of milliseconds is established. The neural network models used in this study are the basic backpropagation neural network model and Elman neural network model, which can manage temporal information. The accuracy of the neural network models is verified using 10 test samples based on the operating conditions. Results of a verification test show that the Elman neural network model performs better than the backpropagation neural network model, with a mean relative error of 4.566% and relative errors of less than 5% in 8 among 10 test cases. The trained neural network can yield a reliable ship bridge collision force instantaneously only when the required parameters are specified and a nonlinear finite element solution process is not required. The proposed model can be used to predict whether a catastrophic collision will occur during ship navigation, and thus hence the safety of crew operating the ship.