• Journal of the FoodService Safety
• /
• v.3 no.1
• /
• pp.38-44
• /
• 2022

This study investigated the microbiological hazards in the manufacturing processes of Naengmyeon. Sanitary indicative bacteria, such as aerobic plate counts and coliforms as well as pathogenic bacteria, were examined from raw materials, manufacturing processes, working area, 17 utensils and equipment. The aerobic plate counts for raw materials and arrowroot starch estimated as 0.77±0.68~5.02±0.28 and 5.02±0.28 log CFU/g, respectively. Coliforms were detected from wheat flour, buckwheat flour, and potato starch. Staphylococcus aureus was detected to be 0.61±1.06 log CFU/g in wheat flour and 0.20±0.35 log CFU/g in buckwheat flour. During the manufacturing process, aerobic plate counts for kneading process were 4.54±0.34 log CFU/g. But after the press out and heat process, contamination of aerobic plate counts and coliforms decreased and remained at a low level until the release process. Aerobic plate counts before washing disinfection of screw were 3.28±0.62 log CFU/100 cm², the level of which was high in utensils and equipment that had contact with employees or water. These results represent not only an important indicator for the hygienic level but also a scientific basis for analyzing biological hazards, which lead to the introduction of HACCP for the production of safe and hygienic cold noodles processed by manufacturers.

• Journal of the Korean Institute of Oriental Medical Informatics
• /
• v.11 no.1
• /
• pp.26-47
• /
• 2005

In this dissertation, I will focus on the channel entry, the effect, and the treatment throughout books of oriental medicine from ancient to modern in order to classify the medicines of the liver as main or supplementary organ. The results are as follows: 1. The kinds of the medicines of working of the liver(本臟) were 29, which were Amydae carapax(鱉甲), Chrysanthemi Flos(菊花), Cassiae Torae Semen(草決明), Plantaginis Semen(車前子), Scirpi Seu Sparganii(三稜), Ulmi Pasta Semen(蕪荑), Cinnamomi Cortex(肉桂), Fraxini Cortex(秦皮), Chaenomelis Fructus(木果), Corii Asini Colla(阿膠), Chuanxiong Rhizoma(川芎), Adenophorae Radix(沙蔘), Coicis Semen(薏苡仁), Acanthopanacis Cortex(五加皮), Zizyphi Spinosae Semen(酸棗仁), Picrorrhizae Rhizoma(胡黃連), Gentianae Radix(草龍膽), Citri Reticulatae Virdie Pericarpium(靑皮), Paeoniae Alba Radix(白芍藥), Paeoniae Rubra Radix(赤芍藥), Bupleuri Radix(柴胡), Peucedani Radix(前胡), Naturalis Indigo(靑黛), Citrus unshiu(橘葉), Rhinocerotis Cornu(犀角), Aucklandiae Radix(木香), Polygonati Odorati Rhizoma, Farfarae Flos(款冬花), Evodiae Fructus(吳茱萸), Citri Reticulatae Pericarpium(陳皮) . 2. The kinds of the medicines of working of other viscera(他臟) were 7, which were Astragaliadix(黃耆), Ginseng Radix(人蔘), pinelliae Rhizoma(半夏), Myristicae Semen, Euryales Semen, Arecae Semen, Piperis Longi Fructus. 3. Medicines, effected on the heart functioned through any other viscera are as follows: Arecae Semen works to treat Spleen Gi Entering the Liver(脾氣入肝), Piperis Longi Fructus, pinelliae Rhizoma(半夏), Euryales Semen and Myristicae Semen operate to treat Spleen Cold Entering the Liver(脾冷入肝), Astragali Radix(黃耆) and Ginseng Radix(人蔘) work to treat Spleen Vacuity Entering the Liver(脾虛入肝). In the study of concerning the medicines effected on the liver, It is considered that it dedicated to development of the medicines related to the disease of the liver and making efficient use of the medicines.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.2
• /
• pp.244-251
• /
• 2011

Pipe rolling process using the planetary rolling mill for AISI 304 stainless steel has been studied by using finite element method. Mannesmann method using three-roll is applied to this rolling process. Commonly, rolling process has started from the cold working and finished to the hot working. This rolling process has more advantage that make reduction of process and cost than existing extrusion process. This process includes various and complex process parameters. Each of the process parameters affects forming result. Therefore, all of the process parameters should be considered in FEA. In this study, possibility and productivity of forming pipe for AISI 304 stainless steel had been investigated. Also, preheating process and variations of rotation velocity and product thickness were considered in FEA. Rolling process for AISI 304 stainless steel pipe was successfully simulated and it should be useful to determine optimal rolling condition.

• Korean Journal of Materials Research
• /
• v.4 no.2
• /
• pp.241-249
• /
• 1994

We studied on the effects of hot-worm rolling on recrystalized structures and tensile strength in over-aged 7075 A1 alloy, to develop the process for improving properties. It showed more clear effect of the grain refinement with over-aging before plastic deformation. That means, the coarse precipitates from over-aging play a roll as nucleation sites in the course of recrystallization. And on this study, the relations between yield strength and grain size was not satisfied with Hall-Petch equation because of the elongated structure, but the yield strength is proportional to aspect ratio of grains. In TMT process for improving strength and toughness, the worm working is available for increase of those properties than cold working.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.5
• /
• pp.58-66
• /
• 2011

A 2-loop waste heat recovery system with Rankine steam cycles for the improvement of fuel efficiency of gasoline vehicles has been investigated. A high temperature loop(HT loop) is a system to recover the waste heat from the exhaust gas, a low temperature loop(LT loop) is for heat recovery from the engine coolant cold relatively. This paper has dealt with a layout of a LT loop system, the review of the working fluids, and the design of the cycle. The design point and the target heat recovery of the LT boiler, a core part of a LT loop, has been presented and analytically investigated. Considering the characteristics of the cycle, the basic concept of the LT boiler has been determined as a shell-and tube type counterflow heat exchanger, the performance characteristics for various design parameters were investigated.

• Solar Energy
• /
• v.17 no.4
• /
• pp.23-33
• /
• 1997

In this paper, performance of various working fluids is evaluated for the closed Ocean Thermal Energy Conversion(OTEC) power plant operating on Rankine cycle. The evaporator and condenser are modeled via UA and LMTD method while turbine and pump are modeled by specifying isentropic efficiencies. R22, Propane, Propylene, R134a, R125, R143a, R32, R410A and Ammonia are used as working fluids. Results show that newly developed fluids such as R410A and R32 that do not cause stratospheric ozone layer depletion perform as well as R22 and ammonia. The superheat at the evaporator exit and subcooling at the condenser exit do not affect the performance of the simple OTEC power cycle. Turbine efficiency and heat exchanger size influence greatly the performance of the Rankine cycle. Finally, it was shown that closed OTEC power plants can practically generate electricity when the difference in warm and cold sea water inlet temperatures is greater than $20^{\circ}C$.

• Journal of Bio-Environment Control
• /
• v.6 no.3
• /
• pp.216-224
• /
• 1997

In the recent 10 years the protected cultivation area in Korea has been increased rapidly, and now it is very important issue to develop the heating and cooling system using the renewable energy, because the greenhouse heating and cooling cost is increased with the fossil fuel price rises. Actually the development of the cooling system is more difficult than that of the heating system, since the cooling load of greenhouse in the summer season is 2―3 times larger than the heating load in the winter season. In this study low temperature phase change materials (LTPCM) for the cold storage system were selected and developed. The theoretical and experimental analysis of thermal characteristics of LTPCM makes it possible to control the phase change temperature and stabilize the thermo-physical properties. LTPCM developed in this study has good advantages to be used as the cold storage not only for the house and working space in factory but also for the cold storage of agricultural and live-stock products.

• Journal of the Korean Institute of Gas
• /
• v.18 no.6
• /
• pp.7-13
• /
• 2014

As the interest on the air pollution is gradually rising up at home and abroad, automotive and fuel researchers have been working on the exhaust emission reduction from vehicles through a lot of approaches, which consist of new engine design, innovative after-treatment systems, using clean (eco-friendly alternative) fuels and fuel quality improvement. This research has brought forward various main issues : whether PM emissions should be regulated for diesel and gasoline vehicles and whether gasoline and LPG powered vehicles can be further neglected from PM emission inventories. Finally, the greenhouse gas ($CO_2$, $CH_4$, $N_2O$) regulation has been discussed including automotive emission regulation. The greenhouse gas and emissions (PM) particle of automotive had many problem that cause of ambient pollution, health effects. This paper discussed the influence of LPG fuel on automotive cold startability and exhaust emissions gas. Also, this paper assessed emission characteristics due to the test temperature. These test temperature were performed by dividing the temperature of the test mode and the lowest local temperature in winter. Through this study, the correlation of cold startability, exhaust emission and greenhouse gas emission was analyzed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.41 no.4
• /
• pp.345-352
• /
• 2017

In this study, the effect of cryogenic liquefied natural gas leakage and loading on liquefied natural gas cargo hold is investigated to observe the performance of the polymer foam material that comprises the cryogenic insulation of the cargo hold. The primary barriers of liquefied natural gas carrier that are in contact with the liquefied natural gas will leak if damage is accumulated, owing to fluid impact loads or liquefied natural gas loading / unloading over a long period. The leakage of the cryogenic fluid affects the interior of the polymer foam, which is a porous closed cell structure, and causes a change in behavior with respect to the working load. In this study, mechanical properties of polyisocyanurate foam specimen, which is a polymer material used as insulation, are evaluated. The performance of the specimens, owing to the cold brittleness and the impregnation effects of the cryogenic fluids, are quantitatively compared and analyzed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.7
• /
• pp.635-643
• /
• 2017

The purpose of this study is to investigate the influence of the cold reduction rate and an ultrasonic fatigue test (UFT) on the fatigue behaviors of STS 304L. The tensile strength, yield strength, hardness value and fatigue limit in the UFT fatigue test linearly increased as thickness decreased from 1.5 mm to 1.1 mm, as the cold reduction rate of STS 304L increased. As a result of the UFT fatigue test (R = -1) of four specimens, the fatigue limit of the S-N curve formed a knee point in the region of $10^6$, and the 2nd fatigue limit caused by giga cycle fatigue did not appeared. In the case of t = 1.1 mm, the highest fatigue limit was 345 MPa, which was 64.3% higher than the original material (t = 1.5 mm). As a result of the UFT fatigue test of STS 304L, many small surface cracks occurred, grown, coalesced while tearing.