• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1499-1502
• /
• 2003

This paper describes the result of carbody and vibration test for freight car. The purpose of the test is to evaluate an safety which carbody structure shall be considered fully sufficient rigidity so as to load a freight car under maximum load and operating condition on line track. The test carbody is constructed by RS korea co., LTD. in accordance with KNR specfication. The test cases of the carbody is tested the vertical load and compressive load to verify the strength and stillness. The vibration test is tested for analysis and evaluation of vibration, to allow for the fact that mechanical vibration in railway vehicles have specific characteristics.

• Design & Manufacturing
• /
• 제10권3호
• /
• pp.34-38
• /
• 2016

Roll forming is a continuous production process that is mass-produced. The roll forming process is produced in various forms. The special feature of roll forming is a continuous production. Therefore, the process of cutting the material is essential. The troubles in a shearing process affects the low productivity. Accordingly, it is important to reduce the factors that inhibit the material flow. And it is difficult to apply the common shear angle. Because it is not a simple forms, such as a progressive die. This study shows how to select the angle of a shear punch and the shape of a cutting punch in the product with a specific shape. Conclusively through three different model, it is advantageous to apply the different shear angle and clearance along the forms.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1990년도 춘계학술대회 논문집
• /
• pp.83-88
• /
• 1990

The study is concerned with the theoretical and experimental investigation of axisymmetric fluid pressure-drive hydronforming of sheet metal by forming over the die cavity. The rigid-plastic finite element method is employed to calculate the stress and strain distribution The effect of blank size and die radius is also studied in the finite element analysis. Experiments are carried out for hydroforming of cold rolled steel sheets under various process conditions. The computational results are compared with the experimental results for the forming pressure vs. pole displacement relations and strain distributions. Comparison has shown that theoretical predictions by the finite element method are in good agreement with the experimental observations. Thus, it is shown that the rigid-plastic finite element method is effectively used in the analysis of axisymmetric fluid pressure-driven hydroforming process.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.161-164
• /
• 1999

In order to investigate the effect of punching condition on the stretch flange formability of sheet for deep drawing hole expansion tests at various edge condition were done. Edge conditions were changed by altering tool clearances artifical defects grinding and deburring. For a determination of optimum edge condition of side panel of automobile punched section analysis and forming results were studied and the laboratory test results were used. In case of considered side panel tool clearance should be less than 15% and punched edge should be uniform without defects for safe forming

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.61-66
• /
• 2000

The fatigue crack initiation life is studied on automotive spot weldment made from cold rolled carbon steel(SPC) sheet by using DCPDM and local strain approach. It can be found that the fatigue crack initiation behavior in spot weldment can be definitely detected by DCPDM system. The local stresses and strains are estimated by elastic-plastic FEM analysis and the alternative approximate method based on Neuber's rule were applied to predict the fatigue life of spot weldment. A satisfactory correlation between the predicted life and experimental life can be found in spot weldment within a factor of 4.

• 한국생산제조학회지
• /
• 제6권3호
• /
• pp.52-57
• /
• 1997

Electronic Speckle Pattern Interferometry(ESPI) using the Model 95 Ar. laser, a video system and an image processor was applied to the in-plane displacement measurements. Unlike traditional strain gauges or Moire method, ESPI method requires no special surface preparation or attachments and can be measured in-plane displacement with no special surface preparation or attachments and can be measured in-plane displacement with no contact and real time. In this experiment specimen was loaded in parallel with a loadcell. The specimen was the cold rolled steel sheet of 2mm thickness, which was attached strain gauges. The study provides an example of how ESPI have been used to measure strain displacement in this specimen. The results measured by ESPI compare with the data which was measured by strain gauge method in tensile testing.

• Journal of Welding and Joining
• /
• 제17권4호
• /
• pp.69-75
• /
• 1999

Spot welding has been used in the sheet metal joining processes because of its high productivity and convenience. In this study, predicting methods of fatigue life of spot welded joint have been investigated and fatigue and static tests were conducted with the peel-tension specimens using cold rolled steel plate(SPCC). Fatigue life of peel-tension spot welded joint was influenced by tail effect. Fatigue life evaluation using modified stress index parameter, considering the effective eccentric length, can predict the life more exactly than conventional stress index parameter.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2018년도 춘계학술대회 논문집
• /
• pp.33.2-33.2
• /
• 2018

현재 업계에서 사용 중인 대부분의 탈지제는 중온 및 고온에서 사용하는 제품이 많으며, 거품의 발생 또한 많으므로 소포제를 넣지 않고서는 사용이 불가능한 약품이 대부분이다. 탈지제 거품의 발생은 탈지제의 세정력을 높이기 위해 주로 사용되는 음이온성 계면활성제의 특성에 의해 나타나게 되는데, 본 연구에서는 음이온성 계면활성제를 사용하지 않음으로 기포의 발생을 억제하고, 동시에 상온에서 사용할 수 있는 약품을 개발함으로써 생산 공정에서의 원가절감과 신뢰성 및 양산성의 향상을 도모하는데 그 목적이 있다.

• Design & Manufacturing
• /
• 제2권2호
• /
• pp.38-42
• /
• 2008

This study is performed for investigating the effects of shearing characteristics in fine blanking, such as camber, burr-height and dimensional accuracy, etc by experiments. Conventional hydraulic press equipped with specially designed hydraulic unit is used for experiments. Cold rolled steel sheet(3.0mm) materials which got properties, 2212.39kgf of maximum, $29.490kgf/mm^2$ of stress and 41.33% of strain were used. it can be concluded that the center distance of vee indenter ring can be obtained 2.0mm in SPCC 3.0t.

• 한국표면공학회지
• /
• 제39권5호
• /
• pp.210-214
• /
• 2006

In order to enhance the electromagnetic shielding efficiency of commercialized cold-rolled steel sheets, we have prepared Ni deposited steel sheets by the electrodeposition method. Surface alloying with Ni and Fe was achieved on a steel sheet by diffusion annealing process. Shielding effectiveness measurement results showed that annealed Ni electrodeposited steel sheets enhanced the shielding efficiency up to about 3 dB in the frequency range of 20 to 200Hz, compared with that of non-deposited steel sheets.