• 콘크리트학회논문집
• /
• 제25권1호
• /
• pp.53-61
• /
• 2013

코일철근의 직선화 가공성을 향상시키기 위한 마디 형상으로, 철근 축과 마디 사이각 $50^{\circ}$, 마디 윗면 폭(crest width) $0.15d_b$, 마디의 종단면 각도(flank inclination) $55^{\circ}$에 초승달 모양 지압면을 가진 생선뼈 마디(fishbone-shaped transverse rib)를 제안하였다. 이 형상은 직선화 기계의 롤러 홈(groove)과 철근 외부의 접촉면적을 넓혀 마디 손상을 최소화하며 직선도를 향상시키고 가공 생산성을 높일 것으로 기대된다. 제안된 형상을 포함하여 마디 각도가 상이한 3종류의 코일철근(SD500D16 강종)에 대한 부착강도 평가를 위해 겹침이음실험을 실시하였다. 3종의 코일철근은 기존 부착강도 평가식에 따른 예측값보다 평균 10%이상 높은 부착강도를 지닌 것으로 평가되었다. 이것은 코일철근의 상대마디면적비가 기존 평가식 유도에 사용된 실험보다 높기 때문으로 판단된다. 부착강도에 대한 직선철근과 코일철근의 상관계수(correlation coefficient)는 0.94이상 이였으며, 코일철근의 부착성능이 직선철근과 거의 유사함을 알 수 있다. 따라서 실험에 사용된 코일철근의 정착길이와 이음길이 설계에 현행설계기준을 적용하는 것이 타당한 것으로 평가된다.

• 설비공학논문집
• /
• 제27권4호
• /
• pp.213-219
• /
• 2015

A thermal storage tank with internal heat exchange coils is commonly used in solar thermal systems with a collector area below $100m^2$. The coils are installed in the lower part of the tank because the temperature of the upper part of the tank can drop if the outlet temperature of the collector becomes lower than the upper temperature of the tank, which is a kind of temperature reversal. As an alternative to the well-mixed storage tank with lower coil only, we have proposed a tank with lower and upper coils and have achieved superior thermal stratification in the tank, which results in increased collector efficiency and solar fraction. But, the phenomenon of temperature reversal was often observed in the tank when the load or solar radiation changed rapidly. In the present work, revised control was successfully applied, i.e., to heat only the lower coil using a three way valve if temperature reversal occurs and to operate the collector at a low flow rate when the quality of solar radiation is not good.

• 한국전기전자재료학회논문지
• /
• 제25권12호
• /
• pp.1000-1003
• /
• 2012

The superconducting fault current limiter (SFCL) can quickly limit the fault current shortly after the short circuit occurs and recover the superconducting state after the fault removes and plays a role in compensating the voltage sag of the sound feeder adjacent to the fault feeder as well as the fault current limiting operation of the fault feeder. Especially, the flux-lock type SFCL with an isolated transformer, which consists of two parallel connected coils on an iron core and the isolated transformer connected in series with one of two coils, has different voltage sag compensating and current limiting characteristics due to the winding direction and the inductance ratio of two coils. The current limiting and the voltage sag compensating characteristics of a SFCL using a transformer winding were analyzed. Through the analysis on the short-circuit tests results considering the winding direction of two coils, the SFCL designed with the additive polarity winding has shown the higher limited fault current than the SFCL designed with the subtractive polarity winding. It could be confirmed that the higher fault current limitation of the SFCL could be contributed to the higher load voltage sag compensation.

• International Journal of Precision Engineering and Manufacturing
• /
• 제2권3호
• /
• pp.54-60
• /
• 2001

A newly designed inductive micro displacement detecting system is presented. The proposed inductive system consists of driving coils, position-detecting coils, cores, and closed-loop formed magnetic blocks. The cores and magnetic blocks are made of Mn-Zn ferrite. When AC sine wave is applied to the driving coils, the time derivative flux is generated within the system, and then induced voltages arise in the position-detecting coils according to the core\`s position. Putting the cores to be moved proportionally to the input displacement, the induced voltage is proportional to input displacement. The parameters that affect the system characteristics are turn ratio, air-gap size, excitation frequency, overlap area, load resistance, capacitance effect, and so forth. Based on the experimental results, the system parameters are selected in such a way as to have high sensitivity ad stable responses. The sensitivity of the proposed inductive displacement-detecting system is greater than 2800mV.V-1mm-1 and the linearity error is below $\pm$0.10% in the range of $\pm$200㎛.

• 한국해양공학회지
• /
• 제24권5호
• /
• pp.22-30
• /
• 2010

The fuel tank of a ship is filled with heavy fuel oil (HFO) that has a very high viscosity. In order to inject the HFO into the engine easily, heating coils are usually installed inside the fuel tank to heat the HFO and lower its viscosity. Currently, several different types of heating coils are used, e.g., fin-type, bare-type, drum-type, and shell-and-tube-type. It is well known that the shell-and-tube-type heating coil has good performance and high efficiency. In this study, experiments were conducted to determine the heat transfer efficiencies of three different shell-and-tube-type heating coils. Heat transfer efficiency was evaluated by using FLUENT 6.3.26 software. Also, structural safety was assessed by using ANSYS.simulation software.

• Transactions on Electrical and Electronic Materials
• /
• 제17권5호
• /
• pp.297-301
• /
• 2016

The effects of ambient temperature and diameter on the insulation lifetime of winding coils prepared with polyamideimide (PAI), flexural PAI (nanosilica 5 wt%) and anti-corona PAI (nanosilica 15 wt%) wires were investigated. The winding coils were made of enameled wire with enamel thickness of 30~50 μm. The thickness and width of the rectangular copper wires were 0.77~0.83 mm and 1.17~1.23 mm, respectively. The insulation breakdown lifetime decreased with increasing ambient temperature regardless of wire type and winding coil diameter under an inverter surge of 1.5 kV/20 kHz. The insulation breakdown lifetimes of φ5 mm winding coils at 150, 200, and 250℃ were 11.38, 5.19, and 4.22 min respectively, and those of φ10 mm winding coils at 150, 200, and 250℃ were 11.32, 5.79, and 4.57min respectively. The winding coil diameter had little effect on the insulation lifetime.

• Journal of Chest Surgery
• /
• 제38권1호
• /
• pp.72-75
• /
• 2005

페 절제술 후의 기관지 늑막루는 지금까지 치료법이 발달하였음에도 불구하고 높은 치명률을 보인다. 수술적 치료를 포함하여 많은 치료법이 발전하였는데 1990년 코일을 이용하여 기관지를 막는 방법이 소개되었다. 이 코일은 물리적인 폐쇄와 섬유화를 유발하여 기관지의 공기 누출을 막을 수 있다. 최근 수술 후 발생한 기관지 늑막루에서 코일을 이용한 치료법을 경험하였기에 보고하고자 한다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2012년도 추계학술대회 논문집
• /
• pp.31-32
• /
• 2012

This paper presents a new design of magnetic bearing structure for application in Nuclear Power Plant (NPP). The proposed design includes so-called saturated coils which is used to generate the bias flux for bearing almost the whole mass of the rotor, and so-called linear auxiliary coil controlled to stabilize the suspension. The saturated coil is considered as an special electromagnet which is controlled to operate in the region of magnetic saturation in order to minimize the bias current as well as to enhance the magnetic flux density. This strategy will result in a very compact size of magnetic bearing as well as increasing the speed of the response of the current controller. The novel structure is expected to be applied to design very high power gas turbine generator of next generation of fast reactor in which the mass of rotor can reach 50 tons. The total power of the NPP can reach 2,000 MW. Moreover, the issue of arc occurrence between coils is also discussed and two solutions are proposed.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제52권3호
• /
• pp.101-106
• /
• 2003

The high temperature superconductor transformers gain interests from the industries. This paper described construction and test results of 10㎸A HTS transformer Three phase transformer with double pancake windings were constructed. To reduce the leakage magnetic field, secondary coil were placed between the two primary coils. BSCCO-2223 wire. silicon sheet steel core and FRP cryostats were used to construct the transformer. Three coils were stacked in one cryostat. Two double pancake coils were connected in series for the primary coil and one double pancake coil was used for the secondary coil. Total number of turns of the primary winding and the secondary winding were 112turns and 98urns, respectively, The rated voltages of each winding were 440/220V. The rated currents of each winding were 13.1/26.2A. After the tests of basic properties of the three phase HTS transformer using no-load test, short-circuit test and full-load test, continuous operation of 100 hours with pure resistive load has been carried out. Test results proved over-load capability and reliability of the HTS transformer.

• 한국지능시스템학회:학술대회논문집
• /
• 한국지능시스템학회 2008년도 춘계학술대회 학술발표회 논문집
• /
• pp.205-208
• /
• 2008

이 논문은 파이프의 결함을 진단하기 위해서 파이프에 유도 비틀림파를 가진하고 수신하는 개선된 방법을 제시한다. 기존에 니켈 스트립을 파이프에 부착하고 잔류자계를 이용한 Mode 선택 가진 방법에서 나타난 잔류자계의 정량화 문제점, 다른 모드가 동시에 가진되는 문제점 등을 해결하기 위해서 새로운 형태의 Crossed Coils센서를 제안한다. 제안된 센서를 통해 모드 선택이 가능함을 확인하였고, 차후 모드분석을 통하여 Torsional Mode의 최적 가진 조건을 찾을 수 있음을 보인다.