• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.798-800
• /
• 2003

Recently, in optical storage device technical trends, the size of optical drive is slimmer to adopt notebook computer and the power of actuator is higher to achieve the high transfer rate. However, these trends of optical disc drives tend to increase the temperature of the actuator part, it causes some problems on the performance of optical parts - the resonance frequency of the actuator is down to lower band and the objective lens, coil and magnet are easily damaged. In this study, to overcome these thermal problems, the numerical simulations of heat transfer were performed. As the result of simulations, the thermal characteristic of the hybrid actuator is better than the previous design. And, it shows the good dynamic performance in experiment.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.879-881
• /
• 2003

For quite a long time various researches and developments of superconducting magnetic energy storage(SMES) device for enhancement of power quality control of sensitive electric toad. This paper describes the design, fabrication and experimental results for the 3MJ SMES magnet made by using the design code of a SMES device that we developed. A computer code was developed to find the parameters of the SMES magnet which has minimum amount of superconductors for the same stored energy, and the 3MJ SMES magnet was designed based upon that.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.965-967
• /
• 1993

In this paper, Take two perment magnets and three iron bars and wind copper wire around one or the bars. This paper demonstrate that the method or calculation yields the right results with MAXWELL-2D program package for computing magnetic field, also indicate the value to which the current in the coil has to be limited to prevent saturation of the iron or the cores. The Finally procedures for design of LDM are discussed.

• Proceedings of the KIEE Conference
• /
• 2005.10c
• /
• pp.135-137
• /
• 2005

In servo system demanding precision dynamic characteristics, application of the Permanent Magnet Linear Synchronous Machines (PMLSM) has advantage of analysis convenience by simple geometry and thrust ripple reduction from the sinusoidal back electromotive force and excited stator. Therefore, this paper presents design of surface-mounted PMLSM with slotless iron cored stator according to coil turns to satisfy the rate thrust. Also, from dynamic analysis for servo application of manufactured motor with heavy mass, we offer accurate range of the DC link voltage and acceleration in rate speed. This is applied to speed reference profile considering system characteristics in total length of moving position.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.2
• /
• pp.110-119
• /
• 1994

The Robust Controller for scan-loop is designed using LQG/LTR Methodology. The design and analysis of spiral, rosette and conical scan patterns are discussed. The perfermance and robustness of the LQG/LTR controller are analyzed through experiments and cpmpared with those of the P-controller. Especially to improve the scan performance at large look angle, the cage coil output is linearized using a binomial equation. It is demonstrated that the scan-loop system by the LQG/LTR control is very robust to phase uncertainties.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.11
• /
• pp.199-207
• /
• 1998

This paper presents the design and the control of three degree-of-freedom(DOF) fine positioning device based on an electro-magnetic force. The device is designed by use of a magnetic circuit theory and it is capable of fine motion due to the electro-magnetic force. The device consists of permanent magnets, yokes and coils. The magnetic fluxes generated from the permanent magnets constitute magnetic paths through steel, whereas the coils are arranged into the gap between two surfaces of the yokes. Therefore, by supplying current to the coils, the coils are capable of some motions due to Lorentz forces. For the optimal design of the actuating system, the system parameters are defined and investigated under the given constraints. From the system modeling in small displacement, three decoupled equations of motion are obtained. To get better performance of the system, a PID controller is implemented. Experimental results are presented in terms of time response and accuracy.

• Proceedings of the KSR Conference
• /
• 1999.11a
• /
• pp.360-367
• /
• 1999

An inverter-driven induction motor is used as the traction motor for a high speed drive system that required safety, reliabillity, performance, compact size owing to the space and weight alloted for attaching to train, etc. particularly it is possible to happen the saturation effects of flux density at constant voltage-frequency region and then increase very higher than the at lowed capacity of no-load current and temperature in any case. therefore the optimum design of core, optimum voltage-frequency ratio, adoption of high grade magnetic core have been developed and researched for preventing these problems. this paper show the saturation effects of traction rotor by measuring the induced voltage of search coil at stator teeth and presents optimum voltage-frequency ratio as well as optimum core design through the comparison with efficiency, power factor, load current and no-load current for korea high speed train.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.10
• /
• pp.146-153
• /
• 1996

This paper presents the development of a collocated capacitance sensor and its application to the controller design for magnetic bearing supported rotor systems. The main feature of the sensor is that it is made of a compact printed circuit board(PCB) so that it can be built into the actuator coil of the magnetic bearing unit. The singnal processing unit hax been also developed. The experi- mental results of the sensor performance evaluation on sensitivity, bandwidth and resolution are presented. Then, simulation study shows the advantages of the collocated sensor for magnetic bearings over the nonco- llocated sensor. Finally, the experimental result on the performance of the collocated sensor based contrl- ler for a magnetic bearing rotor system is presented.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.157-159
• /
• 1996

For the optimal design of the induction heating cooker, precise and accurate analysis of the magnetic field inside the jar must be achieved first. Until now, design methods based on experience has been used in industry field. But this takes a lot of trial and error, high cost and also long development time. So the analysis of the magnetic field distribution is very important. In this paper the magnetic field inside the induction heating cooker is analyzed by using axisymmetrical FEM(finite element method). And the method of the coil location design for the optimal heat source distribution using sensitivity analysis is developed. In addition, the shielding effect of the non-axisymmetrical 3-D ferrite structure used in induction heating cooker is also analyzed by the integral method.

• Progress in Superconductivity and Cryogenics
• /
• v.6 no.3
• /
• pp.38-43
• /
• 2004

1MW class superconducting synchronous motor is designed considering several conditions such as superconducting wire length, machine efficiency and size. As the machine is larger and larger, the superconducting machine shows the advantages more and more over the conventional machines. Although the advantages at 1MW rating are not so great, the design approach to get an appropriate result would be very helpful for larger superconducting synchronous machine design. Major design concerns are focused on reducing expensive Bi-2223 HTS(High Temperature Superconducting) wire which is used for superconducting field coil carrying the rating current around 30K(-243$^{\circ}C$) while the machine efficiency is higher than conventional motors or generators with the same rating. Furthermore, some iron cored structure is considered to reduce the HTS wire requirement without bad effect on machine performances such as sinusoidal armature voltage waveform, synchronous reactance and so on.