• 소성∙가공
• /
• 제7권2호
• /
• pp.139-149
• /
• 1998

The technology of Semi-Solid Forging(SSF) has been actively developed to fabricate near net shape products using light and hardly formable materials. Generally the SSF process is composed of slug is compressed during a certain holding time in order to completely fill the die cavity and accelerate the solidification rate. The decision of compression time is important since it can affect microstructural characteristics, mechanical properties and shape of products.. In order to determine it proper overall heat transfer coefficient between the slug and dies should be investigated. This paper presents the procedure to find the overall heat transfer coefficient between the slug and dies by nonlinear optimization of temperature and solid fraction for a cylindrical slug at compression step in closed-die semi-solid forging. In finite ele-ment heat transfer analysis release of latent heat during solidification was considered. The influence of the predicted compression time on miscrostructural characteristics mechanimcal properties and shape of products is finally investigated by experiment.

• 한국콘텐츠학회논문지
• /
• 제22권7호
• /
• pp.46-54
• /
• 2022

소셜 네트워크에서 영향력을 판별하기 위한 기존 기법들은 소셜 네트워크에서 활동하지 않는 사용자의 수가 증가되는 상황에서 활동을 중단하기 전에 기존 관계를 삭제하거나 갱신하지 않기 때문에 정확하게 사용자의 영향력을 판별하지 못한다. 본 논문에서는 소셜 네트워크의 사용자 생성 일자를 기반으로 한 시간적 k-쉘 분해 방법을 사용하여 영향력 있는 사용자들을 판별하는 기법을 제안한다. 소셜 네트워크에서 오래된 사용자들의 영향력이 높아지는 문제점을 해결하기 위해 주변 이웃의 노화에 따른 감쇠 계수를 k-쉘 분해와 연령 별 차수 중심성을 적용한다. 연령-감쇠 k-쉘 분해와 연령 별 차수 중심성에 감쇠 계수 및 연령에 따른 가중치들을 적용해 현 시점에서 영향력 있는 사용자들을 판별한다. 제안하는 기법의 우수성을 입증하기 위해 다양한 성능 평가를 수행한다.

• 소성∙가공
• /
• 제20권3호
• /
• pp.243-249
• /
• 2011

In this study, an approach designed to compute high temperature friction coefficients for SCM 435 steel through a pilot hot rolling test and a finite element analysis, is proposed. Single pass pilot hot flat rolling tests with reduction ratios varying from 20 to 40% were carried out at temperatures ranging from 900 to $1200^{\circ}C$. In the proposed approach, the friction coefficient is calculated by comparing the measured strip spread and the roll force with the simulation results. This study showed that the temperature and reduction ratio had a significant influence on the friction coefficient. As both material temperature and reduction ratio become higher, the friction coefficient increases monotonically. This finding is not in agreement with the Ekelund model, which is widely used in the analysis of the hot rolling process. In the present work, the friction coefficient at a reduction ratio of 40% was found to be 1.2 times greater than that at a reduction of 30%. This higher friction coefficient means that an increment of the roll thrust force is expected at the next stand. Therefore, a roll pass designer must understand this phenomenon in order to adjust the reduction ratio at the stands while keeping the driving power, the roll housing structure and the work roll strength within the allowable range.

• 소성∙가공
• /
• 제30권2호
• /
• pp.83-90
• /
• 2021

In this paper, a parametric study on the influence of friction between materials on pull force in single clinching is conducted using an axisymmetric elasto-plastic finite element method and law of Coulomb friction. An appropriate finite element analysis model is given, which minimizes the effect of the material model and numerical factors including the number of quadrilateral finite elements and blank radius. It is emphasized that the elasto-plastic material model should be employed because the elastic deformation of the internal region is affected more by the pull force. It has been shown that the pull force increases as friction coefficient increases and that the optimized friction coefficient is around 0.4, which is qualitatively comparable with its theoretical value. When the friction coefficient reaches 0.5 in the example studied, the neck fracture is predicted.

• 한국지반신소재학회논문집
• /
• 제19권2호
• /
• pp.1-11
• /
• 2020

대구경 현장타설말뚝의 수평지지 특성은 말뚝의 강성, 인접지반의 수평지반반력에 따라 크게 좌우된다. 특히 말뚝설계 시 많이 활용되는 경험적인 수평지반반력계수는 그 결과의 값에 따라서 지지력의 차이가 크므로 수평지지력을 평가하는 데 매우 중요한 요소임에도 불구하고 대구경 현장타설말뚝에 대한 지반반력계수의 평가가 미흡한 실정이다. 또한, 말뚝의 취약부인 수평하중에 대한 영향범위와 최대 모멘트의 발생위치는 서로 상관관계가 있을 수 있고, 수평하중에 대한 말뚝의 보강영역을 판단하는데 주요 고려사항임에도 기존 연구에서는 이 관계에 대해 평가되지 않았다. 이에 본 연구는 대구경 현장타설말뚝의 수평지반반력계수를 평가하고, 말뚝의 영향범위(1/β)와 최대 모멘트의 발생위치(z_m)의 관계를 조사하고자 대구경 현장타설말뚝에 대한 현장시험과 비선형 해석을 수행하였다. 연구결과, 대구경 현장타설말뚝의 수평지지력은 경험식을 통한 산정결과에 따라 최대 190%정도 차이를 보였다. 또한, 말뚝의 수평거동에 대한 영향범위와 최대 모멘트의 발생위치의 관계는 지반조건에 따라 선형적 관계인 것으로 평가되었다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1997년도 제26회 추계학술대회
• /
• pp.66-75
• /
• 1997

This study was undertaken to investigate tribology characteristics of the alumina ceramics($Al_2O_3$) of the various purity for the variation of ambient condition such as air and vacuum. The wear test was carried out under different experimental condition using the wear test device, which was designed for this study, and in which the annular surface of wear testing specimens as well as mate specimen made of STB2 steel, were subjected to sliding speed, applied load and the sliding distance. The results obtained were as follows. As the ambient pressure decreases, the friction coefficient increases because the protective layer made of absorption due to decrease of the amount of ambient gas can not be formed. As the friction coefficient paticularly for 85% alumina lower than 95% and 99.7% in the alumina purity increases by an influence of heat accumulation caused by small elastic modulus and thermal conductivity. The friction surface of ceramics can be protected in the air by the influence of the oxides transfered from STB2. However, in the vacuum, the protective layer made of the absorption substance can not be formed due to the decrease of ambient gas.

• Tribology and Lubricants
• /
• 제29권1호
• /
• pp.19-26
• /
• 2013

Cu-matrix sintered brake pads and low-alloy heat-resistant steel are commonly applied to basic brake systems in high-energy moving machines. In this research, we analyzed the tribological characteristics to determine the influence of the air velocity between the disk and pad. At a low brake pressure with airflow, the friction stability was decreased as a result of the lack of tribofilm formation at the disk surface. However, there were no significant changes in the friction coefficient under any of the test conditions. The wear rates of the friction materials were decreased with an increase in the airflow velocity. As a result, the airflow velocity influenced the friction stability, as well as the wear rate of the friction materials and disk, but not the friction coefficient.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.657-662
• /
• 2004

This paper presented is a case study of a real compressor rotor of a refinery plant for high speed balancing of flexible rotor. The rotor was tested in the expert high-speed balancing facility established by KIMM at early 2004. The capability of the facility can reach 40000rpm in rotation speed and 8 ton in rotor weight for high-speed balancing. The facility performs multi-plane at-speed balancing using influence coefficient from the vibration data measured at two pedestals. The test rotor had exceeded permissible criteria of vibration at initial run. But by processing a low-speed balancing at 1000 rpm and six trial run trying to calculate influence coefficient of rotor to the range of operating speed, the final result of high-speed balancing revealed a remarkable reduce of vibration at pedestal of the rotor.

• Journal of Mechanical Science and Technology
• /
• 제17권3호
• /
• pp.422-428
• /
• 2003

This study concerns the performance of the heat transfer of the thermosyphons having 60, 70, 80. 90 axial internal low-fins in which boiling and condensation occurr. Water, HCFC-141b and CFC-11 have been used as the working fluids. The operating temperature, the liquid charge ratio and the inclination angle of thermosyphons have been used as the experimental parameters. The heat flux and heat transfer coefficient at the condenser are estimated from experimental results. The experimental results have been assessed and compared with existing theories. As a result of the experimental investigation, it was found that the maximum heat flow rate in the thermosyphons is dependent upon the liquid charge ratio and inclination angle. A relatively high rate of heat transfer has been achieved by the thermosyphon with axial internal low-fins. The inclination of a thermosyphon has a notable influence on the condensation. In addition, the overall heat transfer coefficients and the characteristics at the operating temperature are obtained for the practical applications.

• 한국지능시스템학회:학술대회논문집
• /
• 한국퍼지및지능시스템학회 1998년도 The Third Asian Fuzzy Systems Symposium
• /
• pp.731-739
• /
• 1998

The probabilistic relaxation(PR) scheme based on the conditional probability and probability space partition has the important property that when its compatibility coefficient matrix (CCM) has uniform components it can classify m-dimensional probabilistic distribution vectors into different classes. When consistency or inconsistency measures have been defined, the properties of PRs are completely determined by the compatibility coefficients among labels of labeled objects and influence weight among labeled objects. In this paper we study the properties of PR in which both compatibility coefficients and influence weights are uniform, and then a learning rule for such PR system is derived. Experiments have been performed to verify the effectiveness of the learning rule.