• Journal of the Korean Ceramic Society
• /
• v.31 no.12
• /
• pp.1521-1528
• /
• 1994

To improve mechanical strength of bioglass, it is considered to use the glass as a coating material to alumina, but the difference in thermal expansion coefficient between two materials is too high to make a good coating. The aim of the present study, therefore, is to find out proper glass composition matching its thermal expansion coefficient to that of alumina without losing biocompatibility. In the present work, various glasses were prepared by substituting B2O3 and CaO for Na2O in the glass system of 55.1%SiO2-2.6%P2O5-20.1%Na2O-13.3%CaO-8.9%CaF2 (in mole%), and the thermal expansion property and reaction property in tris-buffer solution for the resulting glasses were measured. The thermal expansion coefficient of the glass was decreased with the substitution of B2O3 for Na2O, and it became close to that of alumina in the glass in which 8 mole% of CaO was substituted for Na2O. Hydroxyapatite formation was enhanced and silica rich layer thickness was decreased with B2O3 substitution for Na2O. CaO substitution for Na2O didn't deteriorated the hydroxyapatite development.

• Structural Engineering and Mechanics
• /
• v.60 no.2
• /
• pp.313-335
• /
• 2016

In this article, a four-variable refined plate theory is presented for buckling analysis of functionally graded plates subjected to uniform, linear and non-linear temperature rises across the thickness direction. The theory accounts for parabolic distribution of the transverse shear strains, and satisfies the zero traction boundary conditions on the surfaces of the plate without using shear correction factor. Young's modulus and Poisson ratio of the FGM plates are assumed to remain constant throughout the entire plate. However, the coefficient of thermal expansion of the FGM plate varies according to a power law form through the thickness coordinate. Equilibrium and stability equations are derived based on the present theory. The influences of many plate parameters on buckling temperature difference such ratio of thermal expansion, aspect ratio, side-to-thickness ratio and gradient index will be investigated.

• Journal of the Korean Ceramic Society
• /
• v.29 no.7
• /
• pp.533-538
• /
• 1992

Effect of Li2O.4B2O frit on the microstructural and thermal expansion behaviour of $\beta$-spodumene ceramics was investigated. With 4.0~8.0 wt.% frit addition, sintering temperature range was enlarged and densification was enhanced through liquid phase sintering. As the amount of frit addition was increased, thermal expansion coefficient was increased to 1.72$\times$10-6$^{\circ}C$-1 of its highest value, which indicated that the increment of thermal expansion coefficient due to the second phase was constrained.

• Journal of Engineering Education Research
• /
• v.16 no.2
• /
• pp.24-30
• /
• 2013

This paper deals with the measurement theory and technique of linear expansion coefficient for solid material using Michelson interferometer. The Michelson interferometer produces interference fringes by splitting a beam of monochromatic light so that one beam strikes a fixed mirror and the other a movable mirror. When the reflected beams are brought back together, an interference pattern results. Precise distance measurements until a quarter of wave length can be made with the Michelson interferometer by moving the mirror and counting the interference fringes which move by a photo diode. This paper represents the application of Michelson interferometer for measuring infinitesimal length system and shows the measurement method of linear expansion coefficients for various materials like copper, aluminum and iron. the results are good agreement with theoretical value within margin of error for each materials.

• Journal of the Korean Ceramic Society
• /
• v.29 no.8
• /
• pp.646-650
• /
• 1992

Effect of Li2O.4B2O3 frit addition on microstructural and thermal expansion behaviour of the $\beta$-spodumene ceramics made from kaolinite was investigated. With 2.0~4.0 wt% frit addition, the densification by liquid phase sintering caused low water absorption below 3% and enhancement of beding strength. As the amount of frit addition was increased, thermal expansion coefficient was increased to large scale, but in 2 wt% frit addition, its thermal expansion coefficient was constrained to 1.92$\times$10-6$^{\circ}C$-1.

• Journal of Conservation Science
• /
• v.27 no.4
• /
• pp.431-440
• /
• 2011

The thermal expansion coefficient of epoxy/inorganic additives composites was controlled by changing the amount of the inorganic additives such as talc and fused silica. The epoxy resin comprises hydrogenated bisphenol A (HBA)-based epoxide, difunctional polyglycidyl epoxide (DPE) as a diluent and isophorone-diamine (IPDA) as a crosslinking agent, which was subsequently mixed with inorganic additives (talc and fused silica). The thermal expansion coefficient was decreased by increasing amount of inorganic additives, nearly to fresh granite. Fused silica was more effective than talc in lowering the thermal expansion coefficient. Additionally, lexural and tensile strengths of the composites were getting lower and higher with the amount of the inorganic fillers, respectively. It was thus concluded that an epoxy composite containing inorganic fillers was developed to show much lower thermal expansion coefficient, similar to fresh granite, than the neat epoxy resin, and also proper mechanical strengths for applications.

• International Journal of Highway Engineering
• /
• v.10 no.1
• /
• pp.117-122
• /
• 2008

Quality control of the concrete pavement in the early stage of curing is very important because it has a conclusive effect on its life span. Therefore, examining and analyzing the initial behavior of concrete pavement must precede an alternative to control its initial behavior. There are largely two influential factors for the initial behavior of concrete pavement. One is the drying shrinkage, and the other is the heat generated by hydration and thermal change inside the pavement depending on the change in the atmospheric temperature. Thus, the coefficient of thermal expansion and drying shrinkage can be regarded as very important influential factors for the initial behavior of the concrete. It has been a general practice up until now to measure the coefficient of thermal expansion from completely cured concrete. This practice has an inherent limitation in that it does not give us the coefficient of thermal expansion at the initial stage of curing. Additionally, it has been difficult to obtain the measurement of drying shrinkage due to the time constraint. This research examined and analyzed the early drying shrinkage of the concrete and measurements of the thermal expansion coefficients to formulate a plan to control its initial behavior. Additionally, data values for the variables of influence were collected to develop a prediction model for the initial behavior of the concrete pavement and the verification of the proposed model. In this research, thermal expansion coefficients of the concrete in the initial stage of curing ranged between $8.9{\sim}10.8{\times}10^{-6}/^{\circ}C$ Furthermore, the effects of the size and depth of the concrete on the drying shrinkage were analyzed and confirmed.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.809-814
• /
• 2002

Recently, the properties of early-age concrete are increasingly important because these properties directly influence the behavior of early-age concrete structures including stress and cracking behavior. Nevertheless, the studies on early-age concrete are limited to strength and temperature development. The purpose of present study is to propose a simple and rational method which can predict the stress and strain behavior of young age concrete. A series of test have been done to measure the temperature development, strains and stresses in concrete members. The concept of equivalent age was used to define the degree of hydration and this degree of hydration was used to calculate the strength and elastic modulus. The critical degree of hydration and thermal expansion coefficient were calculated using experimental data. It is seen that the critical degree of hydration range from 0.05 to 0.11 based on the measuring method. The thermal expansion coefficient was calculated based on the measured non-mechanical strain and it is found that the coefficient decreases slightly with the increase of age. The consideration of critical degree of hydration in calculating stresses gives more accurate results. The present study provides useful method and data in evaluating early-age behavior of concrete structure.

• Journal of the Korean Ceramic Society
• /
• v.30 no.5
• /
• pp.381-388
• /
• 1993

Due to the anisotropy of thermal expansion, LAS system which has low thermal expansion property is hard to obtain a dense sintered body. Therefore, the thermal expansion coefficient and the mechanical strength were decreased. In this study, mullite, which has good mechanical properties in high temperature and comparatively low thmeral expansion coefficient, was taken as a additive in LAS system. And then, sintering, thermal, and mechanical properties were investigated. The results are follows; When mullite is added in eucryptite composition (Li2O.Al2O3.2SiO2) of LAS system, the creation of liquid phase results in the densification of sintered body and the specimen sintered at 136$0^{\circ}C$ for 2 hours shows optimum sintering condition. With the addition of mullite in eucryptite composition, mechanical strength is increased by the control of grain growth. Especially, flexual strength of EM0 specimen was about double value than the basic composition. Thermal expansion coefficients of EM0 and EM15 specimens sintered at 136$0^{\circ}C$ were -8.23$\times$10-6/$^{\circ}C$ and -4.90$\times$10-6/$^{\circ}C$ in the temperature range of RT.~80$0^{\circ}C$. As the mullite content are increased, negative thermal expansion ratios are decreased.

• Journal of the Korean Ceramic Society
• /
• v.46 no.5
• /
• pp.493-496
• /
• 2009

Phase stabilized leucite, which has high coefficient of thermal expansion, was synthesized, and its thermal expansion behavior was investigated. The homogeneous leucite phase was synthesized by solid state reaction from the mixture of $K_2CO_3-Al_2O_3-SiO_2$. and its stabilization from tetragonal to cubic phase was attempted by adding $Cs_2CO_3$ into starting materials. And fine powder with an average particle size of a few hundreds ${\mu}m$ were fabricated by planetary milling. During milling, amorphization of leucite was observed and recrystallized after heat treatment. The thermal expansion behavior of tetragonal and cubic leucite has measured and discussed. The average coefficient of thermal expansion of tetragonal and cubic phase leucite from room temperature to $750^{\circ}C$ was $21.4{\times}10^{-6}/^{\circ}C$ and $14.5{\times}10^{-6}/^{\circ}C$, respectively.