• Journal of the Korean Magnetics Society
• /
• v.5 no.5
• /
• pp.470-473
• /
• 1995

We have constructed an apparatus for in sity measurement of stress of the film prepared by sputtering using an optical noncontact displacement detector. A Change of the gap distance between the detector and the substrate, caused by stress of a deposited film, was detected by a corresponding change of the reflectivity. The sensitivity of the displacement detector was $5.9\;{\mu}V/{\AA}$ and thus, it was turned out to be good enough to detect stress caused by deposition of a monoatomic layer. The apparatus was applied to in situ stress measurements of Co/X(X=Pd or Pt) multilayer thin films prepared on the glass substrates by dc magnetron sputtering. At the very beginning of the deposition, both Co and X sublayers have subjected to their own intrinsic stresses. However, when the film was thicker than about $100{\AA}$, constant tensile stress in the Co sublayer and compressive stress in the X sublayer were observed, which is believed to be related to a lattice mismatch between the matching planes of Co and X.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1794-1796
• /
• 2000

Oxides of the form $Mn_{3}O_4$-$Co_{3}O_4$-NiO present properties that make them useful as multilayer chip NTC thermistor for mobile communication telephone. When $Mn_{2}Ni_{x}CO_{1-x}O_4$ composition with the X = 0.12$\sim$0.24 at sintered temperature 1250$^{\circ}C$, resistivity and B-constant were 300$\sim$450[${\Omega}-cm$] and 3250$\sim$3450, respectively. Multilayer chip NTC(Negative Temperature Coefficient) resistor were fabricated with 4 layer by a conventional multilayer capacitor techniques, using 100 pd paste as internal electrode and $Mn_{2}Ni_{0.20}CO_{0.8}O_4$ composition as NTC materials. In particular, resistance change ratio (${\Delta}R$), the important factor for reliability, varied within $\pm$3%, indicating the compositions of multilayer chip NTC thermistor products could be available for mobile communication telephone.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.05a
• /
• pp.130-133
• /
• 2002

Solder leaching resistance of the metal electrode is an important factor with regard to adhesion properties of ceramic substrate. In the Low Temperature Co-fired Ceramics (LTCC), Ag-Pd or Ag-Pt pastes are used instead of pure Ag paste to prevent leaching. Solder leaching behavior of the Ag-Pd paste in relation to LTCC raw material powder size was investigated. First fabrication of LTCC green tape with different particle size was done. LTCC substrates with Ag-Pd electrode were prepared using conventional multilayer ceramic process. Dipping test was performed to test solder leaching behavior of the electrode. Ag-Pd electrode on LTCC substrate with smaller particle size achieved higher solder leaching resistance.

• Journal of the Korean Magnetics Society
• /
• v.4 no.3
• /
• pp.256-262
• /
• 1994

$200{\AA}$ thick Co/Pd multilayered thin films were fabricated by sputtering. Two thicknesses of cobalt sublayer, $2{\AA}$ and $4{\AA}$ were chosen and the effects of sputtering pressure on the perpendicular magnetic anisotropy were investigated. It has been found that the optimum pressure for maximum perpendicular magnetic anisotropy(PMA) existed and the pressure for maximum PMA was lower for the multilayer with $2{\AA}$ cobalt layer than that with $4{\AA}$ cobalt thickness. As the sputtering gas presssure increased, domain wall motion with magnetization became difficult and the predominant mode of magnetization reversal changed from domain wall motion to magnetic moment rotation. It turned out that the perpendicular magnetic anisotropy was higher in case of $2{\AA}$ cobalt thickness than $4{\AA}$ cobait thickness.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2007.05a
• /
• pp.33.1-33.1
• /
• 2007

• Electrical & Electronic Materials
• /
• v.16 no.1
• /
• pp.59.1-59
• /
• 2003

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.169-169
• /
• 1999

We studied magnetic properties of co thin films deposited on Pd (111) surface, which attracted much attention recently due to the perpendicular magnetic anisotropy, using magnetic circular dichroism(MCD). Special attention was paid on the effect of Pd capping and interface roughness on the direction of magnetic easy axis, and for that purpose MCD signals for all Co thicknesses were measured with two different ways : in-plane and out-of-plane geometry. In case of bare Co films deposited on smooth Pd(111) surface, no MCD signal was observed under 4$\AA$ co thickness. At 4$\AA$ Co thickness, MCD signal at the out-of-plane geometry was observed, and for thicker Co films, only in-plane MCD signal was measured. This type of magnetic easy axis transition has been reported for other cases like Co/Pt system. The effect of 5$\AA$ Pd capping on these bare Co films made an remarkable change on the transition of magnetic easy axis. Out-of-plane MCD signals exists up to 20$\AA$ Co thickness, and disappears at 24$\AA$ Co thickness. In-plane MCD signals first appears at 10$\AA$ Co thickness and gradually increases up to 24$\AA$ Co thickness. Between 10$\AA$ and 20$\AA$ Co thickness, in-plane and out-of-plane MCD signal coexist. The formation of multi-domain structure or the existence of tilted magnetic easy axis is an possible scenario for such an interesting coexistence. The effect of interface roughness was also tested by measuring MCD signal on Co films deposited on un-annealed Pd(111) surface. Out-of-plane MCD signal was observed up to 8$\AA$ Co thickness and the anisotropy of MCD signal at 4$\AA$ Co thickness was very large with respect to that of Co film deposited on the smooth substrate. Above 8$\AA$ thickness, there exists only in-plane MCD signal. From above results, it was concluded that both Pd capping and interface roughness induce and reenforce the perpendicular magnetic anisotropy. The large perpendicular magnetic anisotropy of Co/Pd multilayer system made by sputtering method can be well understood from our results.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.11
• /
• pp.702-706
• /
• 2014

A comparative study has been attempted for microwave and conventional sintering of lead-free $Bi_{0.5}Na_{0.5}TiO_3(BNT)$-based multilayer ceramic actuators(MLAs). It was found that microwave sintering (MWS) could be successfully applied to the co-firing of piezoceramic/AgPd MLAs with a 10 times shorter firing cycle as well as $100^{\circ}C$ lower firing temperature ($850^{\circ}C$) for sufficient densification than conventional furnace sintering ($950^{\circ}C$). Furthermore, MWS-derived specimens showed better electric field-induced strain than that of CFS-derived specimens by effectively suppressing interdiffusions between ceramic and electrode layers.

• Journal of the Korean Magnetics Society
• /
• v.20 no.3
• /
• pp.89-93
• /
• 2010

We study the giant magneto-resistance (GMR), coercivity and their dependence on the ferromagnetic layers adjacent to the nonmagnetic layer in a spin-valve structure, [Pd/ferromagnetic] multilayers with perpendicular anisotropy. We fabricated a basic spinvalve structure of $[Pd/Co]_2$/ferro-magnetic layer/nonmagnet/ferro-magnetic layer/$[Pd/Co]_2$/FeMn and investigated the dependence of its GMR and magnetic properties such ad coercivity on the ferromagnetic material to reduce the coercivity of the free layer. We try to reduce the freelayer coercivity by controlled the anisotropy, we insert the material NiFe, $Co_8Fe_2$, $Co_9Fe_1$ to ferromagnetic layers adjacent to the Cu layer. Then, we have been able to reduce the coercivity as low as 100 Oe, and also achieved 6.7% of magneto-resistance ratio when the ferromagnetic layer thickness was 0,7 nm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.735-738
• /
• 2003

Downsizing electronics requires precision position control with an accuracy of sub-micron order, which demands development of ultra-fine displacive devices. Piezoelectric transducer is one of devices transferring electric field energy into mechanical energy and being capable for fine displacement control. The transducer has been widely used as fine Position control device Multilayer piezoelectric actuator, one of typical piezo-transducer, is fabricated by stacking alternatively ceramic and electrode layers several hundred times followed by cofiring process. Electrode material should be tolerable in the firing process maintaining at ceramic-sintering temperatures up to $1100{\sim}1300^{\circ}C$. Ag-Pd can be used as stable electrode material in heat treatment above $960^{\circ}C$. Besides, adding small quantity ceramic powder allow the actuator to be fabricated in a good shape by diminishing shrinkage difference between ceramic and electrode layers, resulting in avoidance of crack and delamination at and/or nearby interface between ceramic an electrode layers. This study presents synthesis of nano-oxide-added Ag/Pd powders and its feasibility to candidate material tolerable at high temperature. The powders were formed in a co-precipitation process of Ag and Pd in nano-oxide-dispersed solution where Ag and Pd precursors are melted in $HNO_3$ acid.