• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.4
• /
• pp.140-146
• /
• 1996

A large portion(above 70%) fo the hydrocorbon and NOx emissions for a typical vehicle occur mainly before the conventional underbody catalyst reaches activation temperature. To meet the stringent regulation as EC stage 2, the emissions produced during this period must be reduced. One of alternative techniques is to place CCC(Close-Coupled Catalyst) near the exhaust manifold. In this study, the characteristics of CCC are observed through EEC mode.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.477-478
• /
• 2006

Close-coupled atomizers are of great interest and controlling their performance parameters is critical for metal powder producing and spray forming industries. In this study, designed close-coupled nozzle systems were used to investigate the effect of the nozzle types and protrusion length of the melt delivery tube on the pressure formation at the melt delivery tube tip. The observed metal flow rate was not behaving as what was earlier assumed, namely that, deeper aspiration enhanced metal flow rate. Higher aspiration pressure at the tip of the melt delivery tube increases the stability of atomization process.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.2
• /
• pp.9-16
• /
• 2004

Close-coupled catalyst (CCC) can reduce the engine cold-start emissions by utilizing the energy in the exhaust gas. However, in case the engine is operated at high engine speed and load condition, the catalytic converter may be damaged and eventually deactivated by thermal aging. Excess fuel is sometimes supplied intentionally to lower the exhaust gas temperature avoiding the thermal aging. This sacrifices the fuel economy and exhaust emissions. This paper describes the results of an exhaust heat exchanger to lower the exhaust gas temperature mainly under high load conditions. The heat exchanger was installed between the exhaust manifold and the inlet of close-coupled catalytic converter. The exhaust heat exchanger successfully decreased the exhaust gas temperature, which eliminated the requirement of fuel enrichment under high load conditions. However, the cooling of the exhaust gas through the heat exchanger may cause the deterioration of exhaust emissions at cold start due to the increment of catalyst light-off time.

• Journal of Mechanical Science and Technology
• /
• v.18 no.11
• /
• pp.2032-2041
• /
• 2004

Results from an experimental study of flow distribution in a close-coupled catalytic converter(CCC) are presented. The experiments were carried out with a flow measurement system specially designed for this study under steady and transient flow conditions. A pitot tube was a tool for measuring flow distribution at the exit of the first monolith. The flow distribution of the CCC was also measured by LDV system and flow visualization. Results from numerical analysis are also presented. Experimental results showed that the flow uniformity index decreases as flow Reynolds number increases. In steady flow conditions, the flow through each exhaust pipe made some flow concentrations on a specific region of the CCC inlet. The transient test results showed that the flow through each exhaust pipe in the engine firing order, interacted with each other to ensure that the flow distribution was uniform. The results of numerical analysis were qualitatively accepted with experimental results. They supported and helped explain the flow in the entry region of CCC.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.7
• /
• pp.837-844
• /
• 2003

The exhaust gas flow in the inlet collector of close coupled catalyst(CCC) adapted to the exhaust manifold is very complex flow because the exhaust gas is a pulsation flow with several port flow. The distribution of gas flow and temperature in inlet collector effect to the efficiency of catalytic converter. In this study, it measures temperatures on several point in inlet collector with two kind of inlet collector volume. And it analyzes with CFD to exhaust manifold and close coupled catalyst for temperature and flow. Comparing to measured and analyzed result, it find increasing of collector volume effects to catalyst temperature distribution and uniformity of catalytic converter

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.4
• /
• pp.533-539
• /
• 2001

In this study, results from an experimental and numerical study of flow distribution in a close-coupled catalytic converter (CCC) are presented. The experiments were carried out using a glow measurement system. Flow distribution at the exit of the first monolith in the CCC was measured using a pitot tube under steady and transient flow conditions. Numerical analysis was done using a CF D code at the same test conditions, and the results were compared with the experimental results. Experimental results showed that the uniformity index of exhaust gas velocity decreases as Reynolds number increases. Under the steady flow conditions, flow through each exhaust pipe concentrates on a small region of the monolith. Under the transient flow conditions, flow through each exhaust pipe with the engine firing order interacts with each other to spread the flow over the monolith face. The numerical analysis results support the experimental results, and help explain the flow pattern in the entry region of the CCC.

• The Journal of the Acoustical Society of Korea
• /
• v.17 no.1E
• /
• pp.14-19
• /
• 1998

This article describes the application of a coupled finite element-boundary element method to obtain the steady-state response of a sonar transducer. The sonar shell is simulated to be driven by electrical charges applied onto inner and outer surfaces of the shell. It is shown that at relatively low input frequency a beam pattern which is almost close to omnidirection can be obtained. The coupled FE-BE method is described in detail.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.2 no.1
• /
• pp.37-43
• /
• 1998

This article describes the application of a coupled finite element-boundary element method to obtain the steady-state response of a sonar transducer. The particular structure considered is a flooded piezoelectric spherical shell. The sonar shell is simulated to be driven by electrical charges applied onto inner and outer surfaces of the shell. It is shown that at relatively low input frequency a beam pattern which is almost close to omnidirection can be obtained. The coupled FE-BE method is described in detail.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.335-340
• /
• 2000

Most vehicle's exhaust emissions come from the cold transient period of the FTP-75 test. In this study, UEGI technology was developed to help close-coupled catalytic converter (CCC) reach light-off temperature within a few seconds after cold-start. In the UEGI system, unburned exhaust mixture is ignited by four glow plugs installed upstream of the catalyst. Experimental results showed that the temperature of CCC rises faster with the UEGI technology, and the CCC reaches light-off temperature earlier. Under the conditions tested, the light-off time of the baseline case was 62 seconds and that of the UEGI case was 33 seconds.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.9
• /
• pp.1133-1138
• /
• 2004

Shape optimization method was coupled with a conventional CFD analysis to find the optimal shape of ex-manifold diffuser which decreases the maldistribution of flow above the catalyst. Shape optimization results show that flow uniformity above the catalyst was increased about 28% fur the axi-symmetric case and about 18% for the asymmetric case. The axi-symmetric type can be applied to the diffuser of under floor catalyst and the asymmetric type can be applied to the diffuser of close coupled catalyst.