• International Journal of Fluid Machinery and Systems
• /
• 제3권2호
• /
• pp.137-149
• /
• 2010

The purpose of the present research is to suppress cavitation instabilities by using a circumferential groove. The circumferential groove was designed based on CFD so that the tip leakage vortex is trapped by the groove and does not interact with the next blade. Experimental results show that the groove can suppress rotating cavitation, asymmetric cavitation and cavitation surge. However, weak instabilities with higher frequency could not be suppressed by the groove. From the analysis of pressure pattern similar to that for rotor-stator interaction, it was found that the higher frequency components are caused by the interaction of backflow vortices with the inducer blades.

• Tribology and Lubricants
• /
• 제25권2호
• /
• pp.96-101
• /
• 2009

In order to improve leakage characteristic, angled-circumferential-groove pump seal is suggested. CFD analysis using FLUENT has been performed to predict leakage and determine an optimum slanted-groove angle $\alpha$ which yields the best leakage reduction. The optimum value of $\alpha$ ranges from $45^{\circ}$ to $60^{\circ}$ and depends on the pressure difference of seal and number of grooves for the same groove geometry. The maximum leakage reduction ratio increases as increasing the pressure difference of angled-circumferential-groove pump seal with the optimum value of $\alpha$.

• Journal of Mechanical Science and Technology
• /
• 제14권7호
• /
• pp.737-743
• /
• 2000

This paper presents the effects of circumferential groove on the minimum oil film thickness in engine bearings. The fluid film pressures are calculated by using the infinitely short bearing theory for the convenience of analysis. Journal locus analysis is performed by using the mobility method. A comparison of minimum oil film thickness of grooved and ungrooved bearing is presented. It is found that circumferential $360^{\circ}$ groove only reduces the absolute magnitude of the oil film thickness, but $180^{\circ}$ half groove affects the shape of film thickness curve and position of minimum oil film thickness.

• Tribology and Lubricants
• /
• 제24권6호
• /
• pp.291-296
• /
• 2008

In order to improve the leakage prediction and rotordynamic analysis of an annular seal with a smooth rotor and circumferentially grooved stator, CFD analysis using FLUENT has been performed to determine the groove penetration angle a which is the angle of separation line between control volumes II and III in groove section of Ha and Lee's three-control-volume theory. Validation to the present analysis using new penetration angle determined by the CFD analysis is achieved by comparisons with the results of published Ha and Lee's analysis. For the leakage prediction the present analysis shows slight improvement and CFD results yields the best. Direct damping and cross-coupled stiffness coefficients are predicted better to the experimental ones. However, direct stiffness coefficient is predicted worse.

• 대한기계학회논문집A
• /
• 제37권11호
• /
• pp.1379-1386
• /
• 2013

본 논문에서는 용접부 중앙에 원주방향 관통균열이 있는 V-그루브 맞대기 용접 배관의 한계하중 해석을 수행하였다. V-그루브 맞대기 용접 배관이 그루브 각 $45^{\circ}$, $90^{\circ}$를 갖는 형상에 대한 한계하중 식을 제시하기 위해 용접 형상의 변화에 따른 용접부 너비를 정의하였고 강도불일치 비, 용접부 너비, 균열 길이 및 배관 반경 비에 대한 체계적인 변수 해석을 수행 하였다. 모재와 용접재는 탄성 완전소성재료로 가정하였으며 상불일치와 하불일치 조건에서의 인장 하중과 굽힘 하중에 대한 강도불일치 한계하중이 강도불일치 비($M_F$)와 형상변수(${\psi}$)를 통해 정량화 됨을 유한요소 해석을 통해 확인하였다.

• Tribology and Lubricants
• /
• 제13권4호
• /
• pp.40-46
• /
• 1997

The externally pressurized air journal bearings which have two circumferential grooves with inherently compensated restrictors are analyzed. Two circumferential grooves with restrictors are made on the bearing surface in order to increase the stiffness and damping coefficients. In this paper, the dynamic characteristics such as stiffness and damping coefficients of this type of bearings are calculated. As a result of theoretical analysis, it is verified that there exist the groove depth and the distance between two grooves which generate the maximum stiffness at the given bearing dimensions.

• Tribology and Lubricants
• /
• 제25권1호
• /
• pp.13-19
• /
• 2009

The spools in most hydraulic spool type control valve have several circumferential grooves to pre-vent well known hydraulic locking problems which result in high friction force and excessive wear. In this paper, a commercial computational fluid dynamics (CFD) code, FLUENT is used to investigate the flow and lubrication characteristics of grooved hydraulic spool valve. The stream lines and pressure distributions are obtained for various groove cross sectional shapes and film thicknesses. The stream lines are highly affected by groove cross sectional shape but pressure distributions mainly depend on the film shape and its magnitude. Therefore the numerical method adopted in this paper and results can be use in designing of various grooved spool valve.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1993년도 제18회 학술대회 초록집
• /
• pp.51-56
• /
• 1993

The conical bearing can be used to support the radial and thrust load simultaneously. Two circumferential grooves with discrete hole restrictions are made on the bearing surface in order to increase stiffness. In this paper, the dynamic characteristics of this type of bearings are calculated such as stiffness and champing coefficients. As a results of theoretical analysis, it is verified that there exist the groove depth and distance between two grooves which produce the maximum stiffness at the given bearing dimensions.

• Tribology and Lubricants
• /
• 제10권1호
• /
• pp.56-61
• /
• 1994

The conical bearing can be used to support the radial and thrust load simultaneously. Two circumferential grooves with discrete hole restrictions are made on the bearing surface in order to increase stiffness. In this paper, the dynamic characteristics of this type of bearings are calculated such as stiffness and damping coefficients. As a results of theoretical analysis, it is verified that there exist the groove depth and distance between two grooves which produce the maximum stiffness at the given bearing dimensions.

• Tribology and Lubricants
• /
• 제14권3호
• /
• pp.87-93
• /
• 1998

Crank pin bearing in two-stroke marine diesel engine is operated under quite severe conditions since the elements are big and heavy and the sliding speed is very slow. Therefore it is very difficult to form oil film. In this paper, two types of bearings with different groove shape are compared. One has circumferential oil groove at lower position and the other has lengthwise oil groove at upper position. Bearing clearance, oil inlet pressure and length to diameter ratio are selected as design parameters. Locus of journal center and minimum oil film thickness are investigated to compare two cases.