• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10a
• /
• pp.40-43
• /
• 1996

To design high quality products at low cost is one of very important task for engineers Design optimization for performances can be one solution in this task. This is robust design which has been proved effectively in many field of engineering design. In this paper, the concept of robust design is introduced and combined to fuzzy optimization and nonsingleton fuzzy logic system. The optimum parameter set points were obtained by the fuzzy optimization method and nonsingleton fuzzy logic system. These methods are applied to a filter circuit, a part of the audio circuit of mobile radio transceiver. The results are compared each other.

• Proceedings of the IEEK Conference
• /
• 2004.06b
• /
• pp.505-508
• /
• 2004

Gate length dependent data of intrinsic MOSFET equivalent circuit parameters are extracted using a direct extraction technique based on simple 2-port parameter equations. The relatively scalable data with respect to gate length are obtained. These data are verified to be acrurate by observing good correspondence between modeled and measured S-parameters up to 30GHz. These data will be helpful to construct RF scalable MOSFET model.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05b
• /
• pp.124-127
• /
• 2002

A CMOS voltage regulation circuit for use at low-voltage is proposed. Circuits for a positive and for a negative current regulation are presented and are designed with commercial CMOS technology. The voltage regulation that is stable over ambient temperature variations is an important component of most data acquisition systems. These results are verified by the H-SPICE simulation $0.8{\mu}m$ parameter. As the result, the temperature dependency of output voltage is $0.57mV/^{\circ}C$ and the power dissipation is 1.8 mV on 5V supply voltage.

• Proceedings of the KIEE Conference
• /
• 1990.11a
• /
• pp.380-383
• /
• 1990

When the MOSPET is applied as a switching device for the resonant inverter, a damped oscillating noise is appeared at specific frequency band. This damped Oscillation is caused by the series and parallel resonance due to distributed circuit parameter of snubber and main circuit. This paper describes the frequency-impedance characteristic of the resonant inverter and optimal snubber design strategy to reduce the RF noise.

• Proceedings of the KIEE Conference
• /
• 2003.10b
• /
• pp.86-88
• /
• 2003

The efficiency of electric machine is important due to increase of interest about energy saving. Single Phase Line Start Permanent Magnet Synchronous Motor has high efficiency and power factor. LSPMSM offer a high efficiency as compared induction motor which are used in the home appliance. The analysis and design of LSPMSM is difficult because of unbalanced rotating magnetic field, nonlinear characteristics and rotor saliency. To consider these effects, F.E.M(Finite Element Methods) is coupled equivalent circuit methods. In this paper, a methods of analysis and design using F.E.M and equivalent circuit is represented.

• Proceedings of the KWS Conference
• /
• 1999.10a
• /
• pp.142-145
• /
• 1999

The dynamic resistance monitoring is one of the important issues in that in-process and real time quality assurance of resistance spot weld is needed to increase the product reliability. Secondary dynamic resistance patterns, as a real manner, are hard to adapt those factors in real time and in-plant system. In the present study, a new dynamic resistance detecting method is presented as a practical manner of weld quality assurance at the primary circuit. By the correlation analysis, it is found that the primary dynamic resistance patterns are basically similar to those of the secondary. Various dynamic resistance indices are characterized with the primary curve. And quality of the weld, like the tensile shear strength, is estimated using adaptive neuro-fuzzy estimation system which is consisted of the Sugeno fuzzy algorithm. Through the fuzzy clustering and parameter optimization, real time weld quality assurance system with less efforts is proposed.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.9
• /
• pp.8-13
• /
• 2011

In this paper, a mathematical model of the power LED system including the drive circuit will be presented to control the power LEDs current. Using this mathematical model, the constant current adaptive controller will be designed. A constant current drive circuit for power LEDs will be configured using Buck-type converter. Precise constant current controller design is enabled by presenting the mathematical model of power LEDs including the current driving circuits. Using the mathematical model of power LEDs and its drive circuits, the constant current adaptive controller will be designed to obtain the robustness for the parameter uncertainties. In order to verify the validity of the proposed controller, computer simulations are performed.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.941-942
• /
• 2011

A thermal equivalent circuit of IPMSM considering eddy current loss of PM and core loss of rotor is proposed. This thermal equivalent model is represented by the thermal resistances and thermal capacitances. In order to determine the factor of each parameter, a heating test is processed. Additionally, the eddy current loss of PM is calculated by a transient 3D finite element analysis. Finally, this thermal equivalent model is verified by a temperature test in a 25kW 12-pole/18-slot IPMSM with varying load.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.101-102
• /
• 2011

The attraction force is an important parameter for permanent-magnet(PM) linear machines. This paper aims to analysis lumped magnetic circuit model of a magnetic levitation system. It accounts for the fringing effect and leakage flux which may greatly affect the accuracy of the analytical model for the optimal lumped magnetic circuit model. consequentially it will be able to apply to prospective permanent-magnet(PM) linear machines for accurate analysis.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.502-504
• /
• 1994

This paper describes an induction heating system which is full-bridge parallels resonant inverter. This system consists of current-fed type inverter, and a parallels resonant circuit with a matching transformer. A parallels resonant scheme is employed, and operating range of the proposed circuit with operating frequency and load parameter is demonstrated from the result of steady state. Also, this equipments testing result introduces, good efficiency and reliability of the system. Finally, this paper experimental results are given.