• Korean Membrane Journal
• /
• 제4권1호
• /
• pp.7-11
• /
• 2002

A radial pleat module using a polysulfone membrane was developed. The permeation characteristics of the radial pleat module were compared with those of a flat plate module. The average module efficiency of the radial pleat module for the applied pressure range was 82% and was always greater than that of the spiral wound module. For the radial pleat module, in general, as the applied pressure increases, the flux increases and the rejection reduces. The concentration polarization causes the decrease of the flux for the long time operation. But it has been found that the radial pleat module is more efficient for the reduction of the concentration polarization because it has the more effective area per unit volume and can induce the turbulent flow in the module.

• Current Photovoltaic Research
• /
• 제5권1호
• /
• pp.33-37
• /
• 2017

Today, photovoltaic power generation mostly uses Si crystalline solar cell modules. The most vulnerable part of the Si solar cell module is that the power generation decreases due to the temperature rise. But, it is widely used because of low installation cost. In the solar market, where Si crystalline solar cell modules are widely used. The CPV (Concentrated Photovoltaic) module appeared in the solar market. The CPV module reduces the manufacturing cost of the solar cell by using non-Si in the solar cell. Also, there is an advantage that a rise in temperature does not cause a drop in power generation. But this requires high technology to install and has a disadvantage that the initial installation cost is expensive compared to normal Si solar cell module. So that we built a testbed to see these characteristics. The testbed was used to measure the amount of power generation in a long-term outdoor environment and compared with the general Si solar cell module.

• Membrane and Water Treatment
• /
• 제8권6호
• /
• pp.529-541
• /
• 2017

A multi-effect air gap membrane distillation (ME-AGMD) module for pesticide wastewater treatment is studied with internal heat recovery, sensible heat of brine recovery, number of stages and the use of fresh feed as cooling water in a single module is implemented in this study. A flat sheet polytetrafluroethylene (PTFE) membrane was used in the 4-stage ME-AGMD module. The maximum value of permeate flux could reach $38.62L/m^2h$ at feed -coolant water temperature difference about $52^{\circ}C$. The performance parameter of the module like, specific energy consumption and gain output ratio (GOR) was investigated for the module with and without heat recovery. Also, the module performance was characterized with respect to the separation efficiency of several important water quality parameters. The removal efficiency of the module was found to be >98.8% irrespective water quality parameters. During the experiment the membrane fouling was caused due to the deposition of the salt/crystal on the membrane surface. The membrane fouling was controlled by membrane module washing cycle 9 h and also by acidification of the feed water (pH=4) using 0.1M HCl solution.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.1201-1206
• /
• 2003

A measurement device for gas flow rate using hot-wire module is developed for the utilization in low-accuracy industrial applications. The module has three wires of measuring and heating, and a bridge circuit is installed to detect electric current through the wire in the module. An amplification of the signal and conversion to digital output are conducted for the online measurement with a personal computer. In addition, temperature distribution in the module is numerically analyzed to examine the measured outcome from the module experiment. The flow rate of air and carbon dioxide gas is separately measured for the performance examination of the device. The experimental relation of measurement and flow agrees with the prediction from the numerical analysis. The outcome of the performance test indicates that the accuracy and reproducibility of the module is satisfactory for the purpose of industrial applications.

• Current Photovoltaic Research
• /
• 제6권2호
• /
• pp.62-67
• /
• 2018

Multi-wire busbar-type bifacial n-type Si solar cells have been used for the fabrication of monofacial and bifacial photovoltaic (PV) module, where bifacial module was equipped with transparent backsheet while monofacial module was prepared using white backsheet. The comparison of six-day accumulated power production obtained from outdoor test under gray cement ground conditions using 60cell monofacial and bifacial PV modules suggested the bifacial gain of over 20% could be achieved. Furthermore, the outdoor evaluation tests of bifacial modules with different ground conditions such as cement (reference), green paint, white paint and green artificial grass, were performed. It turned out white paint showed the best albedo and thus the highest power production, while green paint and artificial grass showed less power generation than cement ground.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.2490-2495
• /
• 2005

The scheduling of plant should be determined based on the product demands correctly forecasted by reasonable methods. However, because most existing forecasting packages need user's knowledge about forecasting, it has been hard for plant engineers without forecasting knowledge to apply forecasted demands to scheduling. Therefore, a forecasting module has been developed for plant engineers without forecasting knowledge. In this study, for the development of the forecasting module, an automatic method using the ARIMA model that is framed from the modified Box-Jenkins process is proposed. And a new method for safety inventory determination is proposed to reduce the penalty cost by forecasting errors. Finally, using the two proposed methods, the web-based automatic module has been developed.

• 멤브레인
• /
• 제18권1호
• /
• pp.1-6
• /
• 2008

아크릴 폐수를 응집-여과-중화의 전처리 공정에 적용하여 막오염 인자를 최소화 한 후 UF/RO 공정에 적용하였다. 막의 형태 및 종류에 따라 한외여과 및 역삼투 모듈을 조합을 이루어 전처리 수를 온도 및 압력변화에 따라 적용하여 분리 특성을 고찰하였다. 투과 플럭스는 모듈 set 1의 UF모듈보다 모듈 set 4의 UF모듈의 투과량이 약 $2{\sim}3$배 더 많이 배출됨을 확인하였다. 최종적인 투과량은 관형모듈과 조합을 이룬 모듈 set 2와 모듈 set 3이 좋은 결과를 나타내었다. 모든 UF 모듈에서 TDS, T-N 및 COD의 제거 효율은 온도 및 압력변화에 영향을 받지 않고 제거 효율 또한 낮음을 알 수 있었다. RO모듈에서 TDS, T-N 및 COD가 우수한 제거 효율을 보였다. 아크릴 폐수의 최종적인 수질결과는 공장폐수의 배출 허용기준을 만족하였고, 막모듈 조합은 폐수의 재활용 가능성을 확인할 수 있었다.

• Biotechnology and Bioprocess Engineering:BBE
• /
• 제8권4호
• /
• pp.213-220
• /
• 2003

Polymerase chain reaction (PCR) is one of the most widely used analytical tool and is an important module that would benefit from being miniaturized and integrated onto diagnostic or analytical chips. There are potentially two different approaches for the miniaturization of the PCR module: chamber-type and flow-type micro-PCR. These miniaturized PCRs have distinct characteristics and advantages. In this article, we review the necessity of micro-PCR, the materials for the chip fabrication, the surface modification, and characteristics of the two types of micro-PCR. The motivation underlying the development of micro-PCR, the advantages and disadvantages of the various materials used in fabrication and the surface modification methods will be discussed. And finally, the precise features of the two different types of micro-PCR will be compared.

• 멤브레인
• /
• 제19권3호
• /
• pp.183-188
• /
• 2009

아크릴폐수를 광촉매로 전처리하여 막오염인자를 최소화 한 후 막조합공정에 적용하였다. 한외여과막과 정밀여과막을 역삼투막과 조합을 이루어 막조합공정을 구성하였으며 광촉매처리수를 온도 및 압력변화에 따라 막조합공정에 적용하여 분리특성을 확인하였다. 정밀여과막 모듈 혹은 한외여과막 모듈의 투과수는 역삼투모듈로 보내지며 역삼투 모듈의 최종적인 투과량은 모듈 set 2 (MWCO 200,000 UF+RO)의 역삼투 모듈이 우수하였다. UF 및 MF 모듈에서 TDS, T-N 및 COD의 제거효율은 온도 및 압력변화에 영향을 받지 않고 제거효율 또한 낮음을 알 수 있었다. 그러한 결과로 RO 모듈에서 TDS, T-N 및 COD가 우수한 제거효율을 보였다. UF 및 MF모듈에서의 탁도 제거효율은 우수한 경향(제거효율 99% 이상)을 보였다. 막조합공정에서 처리된 광촉매처리수는 배출 허용기준치를 충족하고, 재활용이 가능하였다.

• Current Photovoltaic Research
• /
• 제7권3호
• /
• pp.71-75
• /
• 2019

Solar energy is one of the renewable energy sources. It can respond to expanding energy demand. A solar cell module is designed to have a durability that can be developed over a long period of 25 years to be installed outdoors and perform like a stable power supply. We need Standard Test Condition (STC)-based power output data before and after testing to measure the power output of existing modules. The modules are shown to reduce power output by comparing data before and after outdoor experiments regardless of whether they are indoor or outdoor. It is easy to compare the power output quantities through the module simulator in the indoor. However, it takes a lot of testing time and costs to compare the power output on outdoor in the case of a high number of modules and distance from the module simulator. It can save time and costs if we can check the power output using the data in outdoor. We have used the long-term outdoor test to find the elements out that corresponds to the reductions in power output quantities. We have conducted research that matched the actual and the tests.