• Korean Journal of Food Science and Technology
• /
• v.30 no.5
• /
• pp.1114-1119
• /
• 1998

The stabilities of O/W emulsions (lipophilic core material:lipophobic wall material=3:2, w/w) containing various kinds of emulsifiers were compared to determine the optimal conditions of the HLB (hydrophilic lipophilic balance) value, the concentration and composition of emulsifier, the ratio of core material to the wall material, and the concentration and composition of polymers in the wall material. The effect of different chemical types of emulsifiers and the influence of single vs. binary emulsifier systems were compared with 13 kinds of emulsifier HLB values of $0.6{\sim}16.7$ at the concentration of 0.50%(w/w). The emulsion system was stable (more than 99.0 of ESI value) when the HLB value of the emulsifier was more than 11.0 or less than 2.8 of emulsifier HLB value. But it was unstable (less than 40.0 of ESI value) at the HLB value of the emulsifier between 3.4 and 8.6. Especially, we could find out the emulsion containing the emulsifier of polyglycerol polyricinoleate (PGPR, HLB 0.6) became stable creamy state. And, the ESI value of binary emulsifier system containing 0.25%(w/w) of PGPR and 0.25%(w/w) of polyoxyethylene sorbitan monolaurate (PSML, HLB 16.7) was higher than that of any single emulsifier system at the concentration of 0.50%(w/w). The highest emulsion stability was obtained in the liquefied wall material composed of 0.25%(w/v) of waxy corn starch and 0.50%(w/v) of agar.

• Korean Journal of Soil Science and Fertilizer
• /
• v.7 no.3
• /
• pp.137-140
• /
• 1974

The present-state survey was carried out on reclaimed land of entire country to grasp the farming conditions, soil characteristics and productivities. The results was summarized as follows: 1) Among farmers participating in reclamation, small farmers, which hold land under cultivation less than 1 ha occupied 42 percent of total farmers; while big farmers, hold more than 3 ha, occupied only 11.1 percent. 2) The land use of reclaimed land by reclaimed year had such big variation that mulberry land was decreasing, however, grass land markedly increased. 3) Soils less than 15 percent slope in reclaimed land occupied 68.7 percent of total reclaimed land, and steep sloping land was reclaimed through bench-terraced method, while gently sloping land, through non terraced one. 4) The chemical properties of reclaimed land was very poor, except for phosphate, all element after 10 years of reclamation was under levels of land of cultivation. 5) Amount of fertilizer application to reclaimed land was under that of recommendation. 6) The yield of reclaimed land was 30 to 86 percent of average of land under cultivation.

• Food Science of Animal Resources
• /
• v.28 no.2
• /
• pp.160-164
• /
• 2008

This study was conducted to evaluate the quality attributes of cooked hams made with four hind leg muscles (Biceps femoris, Semimembranosus, Rectus femoris, Gluteus medius) and Longissimus dorsi. Muscles were prepared from three market-weighted crossbreeds ($L{\times}Y{\times}D$) and the pH, proximate chemical composition, color, texture attributes, and sensory properties of cooked pork muscle hams were evaluated. In the raw state, no significant differences in pH were found among the five muscle hams. However, Rectus femoris ham had the highest pH, while Longissimus dorsi ham had the lowest pH (p<0.05). All muscle hams had similar moisture, fat, and ash contents. The protein content (%) was highest in Longissimus dorsi ham (p<0.05). The Hunter L value was highest for Longissimus dorsi ham while Rectus femoris and Gluteus medius hams had the lowest Hunter L values (p<0.05). The Hunter a values were similar in Rectus femoris, Biceps femoris, and Gluteus medius hams, and lowest for Longissimus dorsi ham (p<0.05). Texture attributes were not significantly different among the five muscle hams (p>0.05). The results of sensory evaluation showed that Semimembranosus hams had the highest flavor score, but there were no significant differences among five muscle hams with regard to color, taste, and texture (p>0.05).

• Food Science of Animal Resources
• /
• v.28 no.1
• /
• pp.59-62
• /
• 2008

The aim of this work was to assess the Delvo test for the detection of antimicrobial residues in goat milk. A total of fifty six samples (eight farms, seven samplings each) were analyzed by the Delvo, Eclipse 100, and Parallux tests. None of the samples showed positive results with the Parallux test which is based on immune-chemical methods. However, 37.5% of samples showed positive results with the Delvo test. 3.6% of samples showed positive results with the Eclipse 100 test, which is based on a microbiological method. The Delvo test is included in the 'standard methods for the examination of raw milk' by the National Veterinary Research and Quarantine Service as a microbiological method used for the detection of antimicrobial residues. Because "raw milk" is defined as 'milked state of cow, ewe and goat milk for sale or for processing' in the Animal Food Products Processing Law, the Delvo test should be excluded from the 'standard method for the examination of raw milk', or additional official documents referring to the Delvo test as not appropriate for the detection of antimicrobial residues of goat milk are required.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.377-377
• /
• 2012

Microprocessor technology now relies on copper for most of its electrical interconnections. Because of the high diffusivity of copper, Atomic layer deposition (ALD) $TaN_x$ is used as a diffusion barrier to prevent copper diffusion into the Si or $SiO_2$. Another problem with copper is that it has weak adhesion to most materials. Strong adhesion to copper is an essential characteristic for the new barrier layer because copper films prepared by electroplating peel off easily in the damascene process. Thus adhesion-enhancing layer of cobalt is placed between the $TaN_x$ and the copper. Because, cobalt has strong adhesion to the copper layer and possible seedless electro-plating of copper. Until now, metal film has generally been deposited by physical vapor deposition. However, one draw-back of this method is poor step coverage in applications of ultralarge-scale integration metallization technology. Metal organic chemical vapor deposition (MOCVD) is a good approach to address this problem. In addition, the MOCVD method has several advantages, such as conformal coverage, uniform deposition over large substrate areas and less substrate damage. For this reasons, cobalt films have been studied using MOCVD and various metal-organic precursors. In this study, we used $C_{12}H_{10}O_6(Co)_2$ (dicobalt hexacarbonyl tert-butylacetylene, CCTBA) as a cobalt precursor because of its high vapor pressure and volatility, a liquid state and its excellent thermal stability under normal conditions. Furthermore, the cobalt film was also deposited at various $H_2/NH_3$ gas ratio(1, 1:1,2,6,8) producing pure cobalt thin films with excellent conformality. Compared to MOCVD cobalt using $H_2$ gas as a reactant, the cobalt thin film deposited by MOCVD using $H_2$ with $NH_3$ showed a low roughness, a low resistivity, and a low carbon impurity. It was found that Co/$TaN_x$ film can achieve a low resistivity of $90{\mu}{\Omega}-cm$, a low root-mean-square roughness of 0.97 nm at a growth temperature of $150^{\circ}C$ and a low carbon impurity of 4~6% carbon concentration.

• Textile Coloration and Finishing
• /
• v.5 no.4
• /
• pp.29-41
• /
• 1993

In order to surface Hydrophobilization of Poly(ethylene terephthalate) (PET) fiber samples were treated in the atmosphere of CF$_{4}$ or $C_{2}$F$_{6}$glow discharge. The sample used in this study was PET film which is 75$\mu$m thick made by Teijin, O-Type(Japan). The cleaned samples were placed in plasma reactor made of pyrex glass cylinder, and plasma processing was carried out by glow discharge of CF$_{4}$ or $C_{2}$F$_{6}$ gas, being continuously fed by gas flow and continuously pumped out by a vacuum system. Electric power source for generate plasma state was sustained alternating current(60Hz) and voltage was sustained 600 volt. The duration of plasma treatment varied from 15 to 120 seconds except special case, the monomer gase pressure varied from 0.02 to 0.3 Torr and power range was 10 to 90 watts. The hydrophobic features of changed PET surface were evaluated by contact angle measurement and surface chemical characteristics were analyzed by ESCA. Results can be summerized as follows. 1. The most favorable setting position of substrate was the center area between the two electrodes. 2. $C_{2}$F$_{6}$ discharge current was lower than that of CF$_{4}$ when same voltage was sustained. Treated efficiency between CF$_{4}$ and $C_{2}$F$_{6}$ did not revealed significant differences under same electric power(wattage). 3. When monomer pressure is very low below 0.02 torr, as though substrate is exposed to CF$_{4}$ or $C_{2}$F$_{6}$ plasma, it tend to be hydrophilic through a little of fluorine bond and a great deal of oxidizing reaction. 4. There brought good hydrophobilization when monomer pressure was more 0.1 torr and duration of glow discharge treatment was over 45 seconds. When monomer pressure was too high, discharge current became low. Although prolong the duration, there was no more high hydrophobilization. 5. According to ESCA analysis, there were a little CF bond and a prevailing CF$_{2}$ bond in CF$_{4}$-treated substrate. There were CF$_{3}$, a little CF and a prevailing CF$_{2}$ bond in $C_{2}$F$_{6}$-treated substrate.d substrate.

• Korean Journal of Ecology and Environment
• /
• v.41 no.2
• /
• pp.228-236
• /
• 2008

The purpose of this study was to evaluate fish metric attributes using a model of Lentic Ecosystem Health Assessment (LEHA) and apply the model to the dataset sampled from six sites of Namyang Reservoir during October 2005$\sim$May 2006. The model was composed of 11 metries and the metric attributes were made of physical, chemical and biological parameters. Trophic composition's metrics showed that tolerant species ($M_3$, 80%) and omnivore species ($M_4$, 92%) dominated the fish fauna, indicating a biological degradation in the aquatic ecosystem. The metric of $M_7$, relative proportions of exotic species, also showed greater than 8% of the total, indicating a ecological disturbance. The average value of LEHA model was 24.3 (n= 12) in the reservoir, indicating a "poor condition" by the criteria of An and Han (2007). Spatial variation based on the model values was low (range: $21{\sim}26$), and temporal variation occurred due to a monsoon rainfall. Electrical conductivity (EC) and tropic state index of chlorophyll-$\alpha$ [TSI(CHL)] was greater in the premonsoon than the postmonsoon.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.7
• /
• pp.46-52
• /
• 2006

The effects of surface treatment on the hydrogen storage properties of a $Mg_2Ni$ alloy particle were investigated by the microvoltammetric technique, in which a carbon-filament microelectrode was manipulated to make electrical contact with the particle in a KOH aqueous solution. It was found that the hydrogen storage properties of $Mg_2Ni$ at room temperature were improved by the surface treatment with a nickel plating solution. The sodium salts(sodium phosphate and sodium dihydrogen citrate) contained in the nickel plating solution made the alloy form an amorphous-like state, resulting in an improved hydrogen charge/discharge capacity at room temperature as high as about 150[mAh/g] from the original value of 17[mAh/g]. Potential-step experiment was carried out to determine the apparent chemical diffusion coefficient of hydrogen atom($D_{app}$) in the alloy. Since the alloy particle we used here was a dense, conductive sphere, the spherical diffusion model was employed for data analysis. $D_{app}$ was found to vary the order between $10^{-8}{\sim}10^{-9}[cm^2/s]$ over the course of hydrogenation and dehydrogenation process.

• Horticultural Science & Technology
• /
• v.29 no.2
• /
• pp.151-155
• /
• 2011

The fungus Botrytis cinerea causes fruit rot of strawberry and the damages can result in harvest losses upto 50%. Proper timing of fungicide application is essential for successful control of Botrytis fruit rot, fenhexamid plus iminoctadine tris, cyprodinil plus fludioxonil, fludioxonil alone, and Bacillus subtilis QST713 were applied to individual buds, flowers, and green and red fruit of cultivar 'Seolhyang' ex vivo. Cyprodinil plus fludioxonil or fludioxonil alone was applied i) before and after a 5-hr period of low-temperature ($0^{\circ}C$) incubation ex vivo ii) in field trials. Strawberry flowers and red fruit were more susceptible to B. cinerea than the green fruits. Incidence of Botrytis rot with fenhexamid plus iminoctadine tris and cyprodinil plus fludioxonil was the lowest at flowering, whereas B. subtilis QST713 did not significantly among treatments. In 2010, incidence of Botrytis fruit rot was significantly reduced when fludioxonil was applied two times at 1 week intervals from 50% bloom in field trials. Cultivars Redpearl and Seolhyang were more susceptible to low-temperature than cvs. Maehyang and Akihime. Cyprodinil plus fludioxonil application was effective when applied before onset of the low-temperature treatment period. Fludioxonil showed the most effective when it was sprayed one and more than two times in before and post low-temperature condition, respectively. These results demonstrate that fungicide selection and timing can interact with stage of fruit development and low-temperature in determining effectiveness of suppression of Botrytis fruit rot.

• Applied Chemistry for Engineering
• /
• v.9 no.4
• /
• pp.579-584
• /
• 1998

Polymer dispersed liquid crystal(PDLC) composite films were made by polymerization induced phase separation method using UV-curing to investigate the effect of fabrication conditions, such as photoinitiator concentration, film thickness, polymerization temperature, and electric field during polymerization, etc., on the electro-optic properties. As the amount of photoinitiator increased, the driving voltage of PDLC device increased due to the increase of small-size liquid crystal phases. This was considered as the results from the increased interfacial area between liquid crystal (LC) and polymer matrix, since LC molecules at the interfacial regions were relatively difficult to response for the applied electric field. When the higher molecular weight oligomer (PTDA-1000) was used as matrix, the initial transmittance was observed to be relatively higher than that for the lower molecular weight oligomer (PTDA-250). Saturation transmittance for PTDA-1000 was observed at relatively lower voltage than that for PTDA-250, of which transmittance was not saturated even at 60 V. As polymerization temperature increased, the initial transmittance of resulting PDLC film increased due to the larger LC droplets formation and the more matched refractive index between LC and matrix than those cases for the lower polymerization temperature. Though driving voltage decreased for the thinner film, it was considered that optimum thickness of the film should be maintained to get some practical contrast, which is the ratio of off- and on-state transmittance. Furthermore, electro-optic properties such as initial transmittance, driving voltage, and response time were observed to be considerably affected by application of external field during polymerization.