• Journal of Electrical Engineering and Technology
• /
• v.13 no.2
• /
• pp.886-891
• /
• 2018

Colloid silica using as abrasive for polishing sapphire has been extensively studied, which mechanism has also been deeply discussed. However, by the requirement of application enlargement and cost reduction, some new problems appear such as silica service life time, particle diameter mixing, etc. In this paper, several influences of colloid silica usage on sapphire CMP are examined. Results show particle diameter and concentration, pH value, service life time, particle diameter mixing heavily influence removal rate. Further analysis discloses there are two main effect aspects which are quantity of hydroxyl group, contact area for abrasive density stacking between abrasive and sapphire. Based on the discussions, a dynamic process of sapphire polishing is proposed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.211-213
• /
• 1999

In this paper, we documented the controlling oxide removal amount on the pattern wafer using removal rate and removal thickness of blanket wafer. There was the strong correlation relationship for both(correlation factor:0.7109). So, we could confirm the repeatability as applying for STI CMP process from the obtained linear formular. As the result of repeatability test, the difference of calculated polishing time and actual polishing time was 3.48 seconds based on total 50 lots. If this time is converted into the thickness, it is from 104$\AA$ to 167$\AA$. It is possible to be ignored because it is under the process margin.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2003.12a
• /
• pp.122-125
• /
• 2003

We investigated the effect of the abrasive and additive concentrations in Nano ceria slurry on the pad surface temperature under varying pressure through chemical mechanical polishing (CMP) test using blanket wafers. The pad surface temperature after CMP increased with the abrasive concentration and decreased with increase of the additive concentration in slurries for the constant down pressure. A possible mechanism is that the additive adsorbed on the film surface during polishing decreases the friction coefficient, hence the pad surface temperature gets lower with increase of the additive concentration. This difference of temperature was more remarkable for the higher concentration of abrasives. In addition, in-situ measurement of spindle motor was carried out during oxide and nitride polishing. The averaged motor current for oxide film was higher than that for nitride film, which means the higher friction coefficient.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.558-559
• /
• 2007

A commercially de-waxer which kinds of solvent after was used to remove a thick organic wax film after polishing process and several steps of SC-1 cleanings were followed for the removal of organic wax residues and particles which requires long process time and high cost of ownership (COO). DIO3 was used to remove organic wax residues too achieve low COO. In this study, 0103 rinsing could use instead of 01 water rinsing. The process time and chemical consumption were reduced by using DIO3.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.193-194
• /
• 2005

By the high-temperature pad conditioning process: The slurry residues in pores and grooves of the polishing pad were clearly removed. These clear pores and enlarged grooves made the slurry attack the oxide surface. The changed slurry properties by high-temperature pad conditioning process made the oxide surface hydro-carbonate to be removed easily.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.487-487
• /
• 2009

One of the critical consumables in chemical mechanical polishing (CMP) is a specialized solution or slurry, which typically contains both abrasives and chemicals acting together to planarize films. In single abrasive slurry (SAS), the solid phase consists of only one type of abrasive particle. On the other hand, mixed abrasive slurry (MAS) consists of a mixture of at least two types of abrasive particles. In this paper, we have studied the CMP characteristics of mixed abrasive slurry (MAS) retreated by adding of $CeO_2$ abrasives within 1:10 diluted silica slurry (DSS). The slurry designed for optimal performance should produce reasonable removal rates, acceptable polishing selectivity with respect to the underlying layer, low surface defects after polishing, and good slurry stability. The modified abrasives in MAS are evaluated with respect to their particle size distribution, surface morphology, and CMP performances such as removal rate and non-uniformity. As an experimental result, we obtained the comparable slurry characteristics compared with original silica slurry in the viewpoint of high removal rate and low non-uniformity.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.88-91
• /
• 2003

Tungsten is widely used as a plug for the multi-level interconnection structures. However, due to the poor adhesive properties of tungsten (W) on $SiO_2$ layer, the Ti/TiN barrier layer is usually deposited onto $SiO_2$ for increasing adhesion ability with W film. Generally, for the W-CMP (chemical mechanical polishing) process, the passivation layer on the tungsten surface during CMP plays an important role. In this paper, the effect of oxidants controlling the polishing selectivity of W/Ti/TiN layer were investigated. The alumina ($Al_2O_3$) abrasive containing slurry with $H_2O_2$ as the oxidizer, was studied. As our preliminary experimental results, very low removal rates were observed for the case of no-oxidant slurry. This low removal rate is only due to the mechanical abrasive force. However, for Ti and TiN with $H_2O_2$ oxidizer, different removal rate was observed. The removal mechanism of Ti during CMP is mainly due to mechanical abrasive, whereas for TiN, it is due to the formation of metastable soluble peroxide complex.

• Fire Science and Engineering
• /
• v.32 no.6
• /
• pp.108-116
• /
• 2018

A melted bead microstructure can be divided into a deformed and undeformed layer. Measurement errors occur in the presence of a deformed layer, which should be removed through grinding/polishing whilst preserving the original structure. This paper proposes a grinding/polishing process to analyze the microstructure of copper melted beads. For the removal of the deformed layer, the correlation between the abrasive type/size, the polishing time and polishing rate was analyzed and the thickness of the deformed layer was less than $1{\mu}m$. The results suggest a new grinding/polishing procedure: silicon carbide abrasive $15{\mu}m$ (SiC P1200) 2 min, and $10{\mu}m$ (SiC P2400) 1 min; and diamond abrasive $6{\mu}m$ 8 min, $3{\mu}m$ 6 min, $1{\mu}m$ 10 min, and $0.25{\mu}m$ 8 min. In addition, a method of increasing the sharpness of the microstructure by chemical polishing with $0.04{\mu}m$ colloidal silica for 3 min at the final stage is also proposed. The overall grinding/polishing time is 38 min, which is shorter than that of the conventional procedure.

• Journal of the Korean Vacuum Society
• /
• v.9 no.2
• /
• pp.102-109
• /
• 2000

It is difficult to meet the cleanliness requirement of $10^{10}/\textrm{cm}^2$ for the giga level device fabrication with mechanical cleaning techniques like scrubbing which is widely used to remove the particles generated during Chemical Mechanical Polishing (CMP) processes. Therefore, the second cleaning process is needed to remove metallic contaminants which were not completely removed during the mechanical cleaning process. In this paper the experimental results for the removal of the metallic contaminants existing on the wafer surface using remote plasma $H_2$ cleaning and UV/$O_3$ cleaning techniques are reported. In the remote plasma $H_2$ cleaning the efficiency of contaminants removal increases with decreasing the plasma exposure time and increasing the rf-power. Also the optimum process conditions for the removal of K, Fe and Cu impurities which are easily found on the wafer surface after CMP processes are the plasma exposure time of 1min and the rf-power of 100 W. The surface roughness decreased by 30-50 % after remote plasma $H_2$ cleaning. On the other hand, the highest efficiency of K, Fe and Cu impurities removal was achieved for the UV exposure time of 30 sec. The removal mechanism of the metallic contaminants like K, Fe and Cu in the remote plasma $H_2$ and the UV/$O_3$ cleaning processes is as follows: the metal atoms are lifted off by $SiO^*$ when the $SiO^*$is evaporated after the chemical $SiO_2$ formed under the metal atoms reacts with $H^+ \; and\; e^-$ to form $SiO^*$.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1573-1575
• /
• 2004

An alumina membrane with nano-sized pores was fabricated by anodic oxidation. The shape and structure of the pore on alumina membrane were changed according to the roughness of aluminum surface. The shape and structure of the nano-sized pre were investigated according to purity of aluminum substrate for the anodization process. The aluminum substrates with 99.5% and 99.999% purities were used. The aluminum substrate(99.5%) was anodized after the processes of pressing, mechanical polishing, chemical polishing, and electrochemical polishing. The nano-sized pores with the pore size of 50 - 100nm, the cell size of 20-50nm and the thickness of $10{\mu}m{\sim}45{\mu}m$ were obtained. Even though the electrochemical polishing was used for the aluminum substrate (99.999%), the same characteristics as the aluminum substrate (99.5%) was obtained. The alumina membrane prepared by anodization for 5 min using fixed voltage method shows the pore with irregular shape. The pore shape was changed to regular shape after pore widening process.