• Asian Journal of Atmospheric Environment
• /
• v.6 no.4
• /
• pp.288-303
• /
• 2012

In this study, real time measurements of particle number size distribution in urban Gwangju, coastal Taean, and industrial Yeosu in Korea were conducted in 2008 to understand the occurrence of ultrafine particle (UFP) (<100 nm) events, the variation of its concentration among different sampling sites, and UFP formation pathways. Also, to investigate seasonal and long-term variation of the UFP number concentration, data were collected for the period of 5 years (2007, 2008, 2010, 2011, and 2012) in urban Gwangju. Photochemical and combustion events were found to be responsible for the formation of UFP in the urban Gwangju site, whereas only photochemical event led to the formation of UFP in the coastal Taean site. The highest UFP concentration was found in industrial Yeosu (the average UFP number fractions were 79, 59 and 58% in Yeosu, Gwangju, and Taean, respectively), suggesting that high amount of gas pollutants (e.g., $NO_2$, $SO_2$, and volatile organic carbon (VOC)) emitted from industries and their photochemical reaction contributed for the elevated UFP concentration in the industrial Yeosu site. The UFP fraction also showed a seasonal variation with the peak value in spring (61.5, 54.5, 50.5, and 40.7% in spring, fall, summer, and winter, respectively) at urban Gwangju. Annual average UFP number concentrations in urban Gwangju were $5.53{\times}10^3\;cm^{-3}$, $4.68{\times}10^3\;cm^{-3}$, $5.32{\times}10^3\;cm^{-3}$, $3.99{\times}10^3\;cm^{-3}$, and $2.16{\times}10^3\;cm^{-3}$ in the year 2007, 2008, 2010, 2011, and 2012, respectively. Comparison of the annual average UFP number concentration with urban sites in other countries showed that the UFP concentrations of the Korean sites were lower than those in other urban cities, probably due to lower source strength in the current site. TEM/EDS analysis for the size-selected UFPs showed that the UFPs were classified into various types having different chemical species. Carbonaceous particles were observed in both combustion (soot and organics) and photochemical events (sulfate and organics). In the photochemical event, an internal mixture of organic species and ammonium sulfate/bisulfate was identified. Also, internal mixtures of aged Na-rich and organic species, aged Ca-rich particles, and doughnut shaped K-containing particles with elemental composition of a strong C with minor O, S, and K-likely to be originated from biomass burning nearby agricultural area, were observed. In addition, fly ash particles were also observed in the combustion event, not in the photochemical event.

• Resources Recycling
• /
• v.13 no.1
• /
• pp.14-21
• /
• 2004

Spent catalysts containing platinum were generated in petroleum refinery and other chemical industries. The reclamation of platinum metals from such wastes has long been attempted in view of their rare, expensive and indispensable nature. In this study, the recovery of platinum from petroleum catalysts was attempted by a method consisting mainly of dissolving alumina carrier with sulfuric acid thereby concentrating insoluble platinum. Also, platinum dissolved partially in sulfuric acid was recovered by a cementation method using aluminum metal as a reductive agent. The effect of temperature, time, concentration of sulfuric acid, and pulp density on the dissolution of carrier was investigated. When the carrier of platinum catalyst was $\Upsilon-Al_2$O$_3$ about 95% alumina was dissolved in 6.0 M sulfuric acid at $100^{\circ}C$ for 2 hours. When the carrier was the mixture of $\Upsilon-Al_2$$O_3$ and $\alpha$-$Al_2$$O_3$ about 92% was dissolved after 4 hours. As a result, more than 99% of platinum could be recovered by this method and aluminum sulfate was also obtained as byproduct.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.4
• /
• pp.595-601
• /
• 2014

The microstructures of NATM were examined by SEM, FT-IR spectra, tensile properties, mole % of [NCO/OH], and particle size analyzer. Growing concerns in the environment-friendly industries have led to the development of solvent-free formulations that can be cured. We had synthesized NATM(New Austria Tunnel Method) resin having the ability to protect stainless steel against corrosion. Comparing with general NATM resin and coatings, this resin that synthesized with polyurethane and epoxy was highly stronger in intensity and longer durability. Hybrid resin was composed of polyols, MDI, epoxy, silicone surfactant, catalyst and crosslink agent, and fillers. Moreover, fillers such as fume silica not only accelerated the curing rate but also improved the physical property as thermal barriers. The rigid segments of synthetic resin in mechanical properties were due to fume silica and the increase the mole% of [NCO/OH] for corrosion protection. In conclusion, the hybrid resin microstructure with crosslink agent and fume silica are good material for thermosetting coating of metal substrates such as stainless steel.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.4
• /
• pp.584-594
• /
• 2014

To increase of surface hydrophilicity of polymeric thin films is an important approaching technique for introduction of self-cleaning and/or antifogging properties on the surfaces of those films. In general, hydrophilic surface can be produced by coating non ionic surfactants or by increasing surface energy. Various non-ionic surfactants, such as Tween, Span, and PEG-PPG block copolymers were selected for our experiments, because they are cheap and well soluble in toluene system as well as they contain several reactive hydroxy fuctional groups with coupling agents. Blending conditions influence the PET film surface hydrophilicities. However, the introduction of only these surfactants on the surface of PET films did not show the high durability of hydrophilic properties after washing with water. To improve the durability two types of coupling agents such as epoxide and diisocyanate were adopted. Contact angle of water on hydrophilically coated PET film surface with 6 wt% of isophrone diisocyanate(IPDI) containing coating solution was reached to $8.7^{\circ}$, which was an indirect evidence for very high surface hydrophilicity. A light(500 nm of wavelength) transmittance value of coated PET film was changed only from 87% to 85% with keeping a good transparent property. This film can be usable for self-cleaning film industries.

• Journal of Fisheries and Marine Sciences Education
• /
• v.5 no.1
• /
• pp.31-44
• /
• 1993

Through the early 1900's, the evolution of the surface condenser was closely tied to the development of steam engine and the turbine. As the chemical and petroleum industries evolved in the 1900's, the use of surface condensers in many different processes. Today, industry uses condensers in many shapes and sizes. The actual condensation process occurs on the outside surface of tubes. The nature of this surface geometry affects the condenser's heat transfer performance. The first condensers were built with plain tubes. As tube manufacturing techniques advanced, manufacturers started making tubes with integral fins. In the 1940's, fin densities were limited to about 600 to 700 fins per meter(fpm) because of manufacturing procedure. Today new manufacturing techniques allow production of tubes with fin densities ranging from 750 to 1600 fpm. The integral-fin tubes investigated in this paper are nominally 19 mm diameter. Eight tubes have been used with trapezodially shaped integral-fins having fin density from 748 to 1654 fpm and 10, 30 grooves. For comparison, tests are made using a plain tube having the same inside diameter and an outside diameter equal to that at the root of the fins for the finned tubes. Betty and Katz's theoretical modelis is used to predict the R-11 condensation coefficient on horizontal integral-fin tubes having 748, 1024 and 1299 fpm. Experiments are carried out using R-11 as working fluid. The refrigerant condensates at a saturation state of $30^{\circ}C$ on the outside tube surface cooled by coolant. The amount of noncondensable gases present in the test loop is reduced to a negligible value by repeated purging. For a given heat input to the boiler and given cooling water flow rate, all test data are taken at steady state. The observed heat transfer enhancement for the finned and grooved tubes significantly exceeded that to be expected on grounds of increased area. For the eight fin tubes and one plain tube tested, the best performance has been obtained with a tube having a fin density of 1299 fpm, and a fin bight of 1.2mm and 30 grooves.

• Korean Journal of Soil Science and Fertilizer
• /
• v.11 no.3
• /
• pp.195-206
• /
• 1979

Where the industrial waste is increasing in number of kind and in quantities by the industrialization and population increases, the pollution problem is not only national but grobal question of the day. This paper is trying to invite attentions by the people who are working in both sector-natural sciences and industries in reviewing limited reports and materials. 1. By the chemical evaluation of over 20 industrial waste produced in Korea, potential wastes for commercial fertilizer would be wastes from alcohol fermantation, beer brewery, leather processing, synthetic fiber, and coffee grounds. 2. The composition of city waste is differ from other countries and sludge cake from human feces processing is promising one in the organic matter and phosphate content particularly. However, the content of heavy matals, specific order, and availability of phosphate are the bottle-neck for the development. 3. There is one commercial fertilizer from industrial waste in the market. It is very reasonable in the content of nitrogen and organic matter, and its formulation and responeses on crops. 4. Discussions were also given on the general problems in processing and marketing of fertilizers from industrial waste, however, scientists and industrial owners have to pay more attention on the development of fertilizers from tire industrial wastes because of vital environmental protection view-point.

• Korean Journal of Environmental Agriculture
• /
• v.27 no.4
• /
• pp.337-342
• /
• 2008

The nitrogen (N) and phosphorus (P) balances in Korea during 1985-2006, which calculated according to the surface balance method of the PARCOM guidelines, continually increased with the lapse of year, and then might keep the highest levels with about $250kg\;N\;ha^{-1}$ and $50kg\;P\;ha^{-1}$ in 2006 among OECD countries. National phosphorus balance of the developed OECD countries (Belgium, Denmark, Germany, The Netherlands) in the livestock feeding industries has significantly decreased, due to limit livestock feeding density and nutrient application level by using strong legislation. However, Korean P balance was not apparent decrease, since the number of livestock feeding heads has been increasing, irrespective with the decrease of chemical fertilizer consumption. Manure P portion to the total P input amount of the above four OECD Countries in nutrient balance has continuously inclined to 60-70%. Therefore, the large portion of livestock manure might be used as nutrient source in agricultural side in these countries. In particular, manure P application levels of Belgium and The Netherlands, which have relatively high P balance and manure P portion to total P input dose, was estimated to be $31-33\;kg\;p\;ha^{-1}$ in 2004, and it was similar level with that of Korea in 2006. The manure P application levels for agricultural purpose has continuously decreased in these two OECD countries. In contrast, our manure P application rate continuously increased, and therefore we need the strong political countermeasure to control livestock feeding density at the resonable level.

• Applied Chemistry for Engineering
• /
• v.23 no.1
• /
• pp.18-22
• /
• 2012

Photocurable binder for a transparent glass fiber composite was prepared with alicyclic methacrylate and fluorene-based diacrylate. ANOVA (analysis of variance) analysis was used to know main factors affecting the conversion of photocurable binder. It showed radiation intensity and photoinitiator (PI) concentration were main factors. The conversion of photocurable binder was simply increased with radiation intensity. Its increment however was abated with increasing PI concentration. We found that average conversion of the binder measured by FTIR-ATR was 87% when it was exposed to $5J/cm^2$ of UV dose with 5 wt% of PI. Oxime ester type PI was very effective to get a high degree of conversion, but it caused a yellowing problem. Owing to post-baking process, UV cured film showed an improved thermal stability by increase of conversion and removal of volatile organic compounds. TG% at $260^{\circ}C$ of film cured with 5 wt% of PI (TPO+MBF) and $5J/cm^2$ of UV radiation increased from 95.4 to 99.0% by post-baking at $230^{\circ}C$ for 5 min.

• Clean Technology
• /
• v.26 no.2
• /
• pp.91-95
• /
• 2020

A new eco-friendly synthetic method for N-hydroxysuccinimide (NHS), widely used in the pharmaceutical and fine chemical industries, is developed. Conventional synthesis method yields NHS of about 70% after its reaction with NH₂OH to succinic acid. In this method, NHS can be obtained using low-cost succinic acid, but a great deal of solvents are required as an extraction method to purify NHS, while the work-up process is complicated, resulting in low yield. In addition, there is a safety risk due to the high reaction temperature for commercial production, and it is not economical due to the high cost of production from the generation of much waste because of an acid catalyst and the use of various solvents. In order to make up for this shortcoming, this study used succinic anhydride as a raw material under low temperature reaction and developed a new eco-friendly industrial synthesis method using isobutyl alcohol for a single solvent and non-catalytic reaction. The economic evaluation confirms that there is a cost reduction effect of about 20%. In the future, based on this result, studies may establish a commercial production technology through scale-up research and proceed with foreign technology transfer.

• Journal of Life Science
• /
• v.25 no.7
• /
• pp.733-739
• /
• 2015

Microalgae are a renewable natural resource that requires only sunlight, carbon dioxide, phosphorus, and nitrogen for rapid growth. They produce a broad variety of basic chemical substances―such as vitamins, fatty acids and carotenoids―that have high added value potential for the pharmaceutical and food industries. The aim of this study was to develop axenic culture and to establish a cell growth assay for microalgae. A further experiment was carried out to determine the yield of astaxanthin derived from microalgae. The axenic culture was developed using a mixture of antibiotics [ampicillin (100 ${\mu}g/ml$), streptomycin (10 ${\mu}g/ml$), chloramphenicol (10 ${\mu}g/ml$), penicillin (10 ${\mu}g/ml$), neomycin (50 ${\mu}g/ml$), gentamycin (50 ${\mu}g/ml$), kanamycin (10 ${\mu}g/ml$), and nystatin (1.5 ${\mu}g/ml$)] and then used to extract a variety of useful components from the microalgae. The optimal concentration for the antibiotic mixture was 1-3 percent. A spectrophotometric cell growth assay was also established. Astaxanthin was extracted from Haematococus lacustris with a yield of $1.9{\times}10^{-3}{\mu}g/l$ per 1 ml of culture medium. In conclusion, the axenic culture method developed here allows extraction of high-quality astaxanthin and other useful components from microalgae.