• The Korean Journal of Food And Nutrition
• /
• v.1 no.2
• /
• pp.43-49
• /
• 1988

Fermented barley food was produced by the combining action of an enzyme and a lactobacillus. When Lactobacillus sp. L-5 and commercial liquefying amylase from Tae Pyeong Yang Chemical Co. were selected, inoculated on steamed barley and cultivated at 37$^{\circ}C$ for 48hrs, the fermented product of good quality was obtained. In batch cultivation using rotary drum fermentor, viable cell count reached 1.1$\times$10CFU/g after 12hrs' cultivation, and specific growth rate in logarithmic phase was 0.6hr-1. Viable cell count, acidity, pH, concentration of reducing sugar and viscosity of the 48hrs' fermentation product from rotary drum fermentor was 4.3$\times$108CFU/g, 1.17%, 3.1, 10.7% and 1430cp.

• Journal of Korean Society for Atmospheric Environment
• /
• v.20 no.4
• /
• pp.555-569
• /
• 2004

Size -segregated measurements of aerosol composition using 8-stage DRUM impactor are used to determine the transport of natural and anthropogenic aerosols at Gosan site from 29 March to 30 May in 2002. Separation of ambient aerosols by DRUM impactor offers many Advantages over other standard filtration techniques. Some of the most important advantages are the ability to segregate into details by particle tire, to better preserve chemical integrity since the air stream doesn＇t pars through the deposit, to collect samples as a function of time, and to have a wide variety of impaction surfaces available to match analytical needs. Although the transport of Yellow sand is a well-known phenomenon in springtime, the result of measurement shows that not only soil dust but also anthropogenic aerosols, including sulfur, enriched trace metals such as Pb, Ni, Zn. Cu, Cr, As, Se, Br, are transported to Gosan in springtime. This study combines the size- and time-resolved aerosol composition measurements with isentropic, backward air-mass trajectories in order to identify some potential source regions of anthropogenic aerosols. As a result, during the NYS period, the average concentration of PM$_{10}$ was 46$\mu\textrm{g}$/㎥, Si, Al. S, Fe, Cl, K, Ca were higher than 1,000 ng/㎥ and Ti was about 100 ng/㎥. The concentrations of Zn, Mn, Cu. Pb, Br, Rb, V, Cr, Ni. At, Se ranged between 1 and 70 ng/㎥. More than 50% typical soil elements, tuck as Al, Si, Fe, Cd. Ti, Cr, Cu, Br. were distributed in a coarse particle range(5.0-12${\mu}{\textrm}{m}$). In other hand, anthropogenic pollutants, luck as S, N, Vi, were mainly distributed in a fine particle range (0.09-0.56${\mu}{\textrm}{m}$). During the YS period, PM$_{10}$ increased about 8 times than NYS period, and main soil elements, such as Al, Si, S, K, V, Mn, Fe also doubled in coarse particle range (1.15-12${\mu}{\textrm}{m}$). But Zn, As, Pb, Cu and Se, which distributed in the time aerosols (0.09-0.56${\mu}{\textrm}{m}$), were on the same level with or decreased than NYS period. Finally. except the YS Period, coarse particles (2.5-12${\mu}{\textrm}{m}$) are inferred to be influenced by soil, coal combustion, waste incineration, ferrous and nonferrous sources through similar pathways with Yellow Sand. But fine particles have different sources, such as coal combustion, gasoline vehicle, biomass burning, oil or coal combustion, nonferrous and ferrous metal sources, which are transported from China, Korea peninsula and local sources.ces.

• Macromolecular Research
• /
• v.16 no.3
• /
• pp.212-217
• /
• 2008

PVDF ($Kynar^{(R)}$ 761) nanofibers were made by electrospinning with an external voltage of 6-10 kV, a traveling distance of 7-15 cm and a flow rate of 0.4-1 mL/h. Although the mean diameter of the fibers has not changed significantly, the conditions affected the change in diameter distribution. This was attributed to interactions, both attraction and repulsion, between the positive charges on the polymer solutions and the electrically grounded collector. Higher voltages and traveling distance increased the level of attraction between the positive charge on the polymer solution and the electrically grounded collector, resulting in a narrow diameter distribution, In addition, a high flow rate allowed a high population of uniformly charged solutions to travel to the grounded collector, which resulted in a narrow diameter distribution. The optimum conditions for electrospinning of PVDF in DMAc/acetone (3/7 by wt) were a collector voltage of 6 kV, a syringe tip to collector of 7 cm, a flux rate of 0.4 mL/h and 10 kV, 10 cm, 1 mL/h, Since PVDF is widely used as a filtration membrane, it was electrospun on a PET support with a rotating drum as a grounded collector. Surprisingly, some straight nanofibers were separated from the randomly deposited nanofibers. The straight nanofiber area was transparent, while the randomly deposited nanofiber area was opaque. Both straight nanofibers and aligned nanotibers could be obtained by manipulating the PET drum collector. These phenomena were not observed when the support was changed to an Al sheet. This suggests that a pseudo dual collector was generated on the PET sheet. No negative charge was created because the PET sheet was not a conductive material. However, less charge was created when the sheet was not perfectly attached to the metal drum. Hence, the nanotibers jumped from one grounded site to the nearest one, yielding a straight nanofiber.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.6 no.3
• /
• pp.189-203
• /
• 2008

The physical and chemical properties of radioactive waste drums, which have been temporarily stored on site, should be characterized before their shipment to a disposal facility in order to prove that the properties meet the acceptance guideline. The investigation of NDT(Nondestructive Test) method was figured out that the contents in drum, the quantitative analysis of free standing water and void fraction can be examined with X-ray NDT techniques. This paper describes the characteristics of X-ray NDT such as its principles, the considerations for selection of X-ray system, etc. And then, the waste drum characteristics such as drum type and dimension, contents in drum, etc. were examined, which are necessary to estimate the optimal X-ray energy for NDT of a drum. The estimation results were that: $(R)\acute{A}$ the proper X-ray energy is under 3 MeV to test the drums of 320 ${\beta}\S$ and less; $(R)\ddot{E}$ both X-ray systems of 450 keV and/or 3 MeV might be needed considering the economical efficiency and the realization. The number of drums that can be tested with 450 keV and 3 MeV X-ray system was figured out as 42,327 and 18,105 drums (based on storage of 2006. 12), respectively. Four testing scenarios were derived considering equipment procurement method, outsourcing or not, etc. The economical and feasibility assessment for the scenarios was resulted in that an optimal scenario is dependent on the acceptance guide line, the waste generator's policy on the waste treatment and the delivery to a disposal facility, etc. For example, it might be desirable that a waste generator purchases two 450 keV mobile system to examine the drums containing low density waste, and that outsourcing examination for the high density drums, if all NDT items such as quantitative analysis for 'free standing water' and 'void fraction', and confirmation of contents in drum have to be characterized. However, one 450 keV mobile system seems to be required to test only the contents in 13,000 drums per year.

• Journal of the Korean Society of Visualization
• /
• v.16 no.3
• /
• pp.40-46
• /
• 2018

The surface structure of the electrospun polymer fibers depends on the polymer concentration, the type of solvent used, applied voltage and so on. To make a desired surface, it is important to understand the effects of the physicochemical properties to form a stable Taylor cone and jet dispensation. We observed the formation of Taylor cone and a consequent structure of fiber by controlling the parameters of applied voltage, solution concentration, solvent and collector effectively. Once the surfaces were fabricated, the structures were analyzed using optical imaging technologies. As the solution concentration was increased, the smooth fibers were formed. In addition, different solvent ratios determined the viscosity and the surface tension of solutions. As a result, with decreased viscosity and increased surface tension, thin fibers were obtained by electrospinning. Furthermore the aligned nanofiber was successfully created by using drum collector.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.951-954
• /
• 2000

This paper presents a new cutting method, i.e. diamond cutting, aided by electrolysis, in order to cut ferrous materials with diamond tools. Diamond cutting is widely applied in manufacturing ultraprecision parts such as magnetic disk, polygon mirror, spherical/non-spherical mirror and copier drum, etc. because of the diamond tool edge sharpness. In general, however, diamond cutting cannot be applied to cutting steels, because diamond tools wear excessively in cutting iron based materials like steel due to their high chemical interaction with iron in high temperature. In order to suppress the diffusion of carbon from the diamond tool and to reduce increase of cutting force due to size effect, we attempt to change chemically the compositions of iron based materials using electrolysis in a limited part which will be soon cut. Through experiments under several micro-machining and electrolysis conditions, cutting using electrolysis, compared to conventional cutting, was found to result in a great decrease of the cutting force, a better surface and much less wear tool.

• Journal of the Korean Institute of Gas
• /
• v.11 no.2 s.35
• /
• pp.15-24
• /
• 2007

For consequence analysis at a gas explosion by vessel release, release rates, demage areas of facilities, and fatality areas were estimated and analyzed at various conditions(release materials, temperatures, pressures, and vessel types) by using the release scenario of API-581 BRD. Simulation results showed that release rates and consequences in the vessel release were higher than those in the pipe release, and the order of release rates and damage areas was as follows; tank>reactor>drum> column.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.473-476
• /
• 2008

In this paper, we designed the main mechanism of high throughput device for rod-cuts of spent fuel. For this, we analyzed the mechanical methods(slitting, ball mill, roller straightening) and chemical methods(muffle furnace, rotary kiln). As the results, methods of ball drop and rotary drum for concepts design were selected in the analysis step. For enhancement of oxidation rate, we devised the blades on the reactor with mesh type. Also, for enhancement of decladding rate, we designed ball size and rotation reactor with mesh type and devised the vacuum system for fission products. Mechanisms of oxidation and recovery can simultaneously handle the rod-cuts of spent fuel and independently recover. The results of mechanism design can be used for scale-up of high throughput device.

• Journal of Biosystems Engineering
• /
• v.41 no.4
• /
• pp.365-372
• /
• 2016

Purpose: Tea is the most frequently consumed drink worldwide, next to water. About 75% of the total world tea production includes black tea, and withering is one of the major processing steps critical for the quality of black tea. There are two types of tea withering methods: physical and chemical withering. Withering can be achieved by using tat, tunnel, drum, and trough withering systems. Of these, the trough withering system is the most commonly used. This study focuses on the different types of withering, their effect on the various quality attributes of tea, and other aspects of withering methods that affect superior quality tea. Results: During physical withering, tea shoots loose moisture content that drops from approximately 70-80% to 60-70% (wet basis). This leads to increased sap concentration in tea leaf cells, and turgid leaves become flaccid. It also prevents tea shoots from damage during maceration or rolling. During chemical withering, complex chemical compounds break down into simpler ones volatile flavor compounds, amino acids, and simple sugars are formed. Withering increases enzymatic activities as well as the concentration of caffeine. Research indicates that about 15% of chlorophyll degradation occurs during withering. It is also reported that during withering lipids break down into simpler compounds and catechin levels decrease. Improper withering can cause adverse effects on subsequent manufacturing operations, such as maceration, rolling, fermentation, drying, and tea storage. Conclusion: Freshly harvested leaves are conditioned physically and chemically for subsequent processing. There is no specified withering duration, but 14-18 h is generally considered the optimum period. Proper and even withering of tea shoots greatly depends on the standards of plucking, handling, transportation, environmental conditions, time, and temperature. Thus, to ensure consumption of high quality tea, the withering step must be monitored carefully.

• KSBB Journal
• /
• v.16 no.5
• /
• pp.505-510
• /
• 2001

The preparation, characterization and drug release behaviour of drug(indomethacin) loaded Poly(L-lactic acid)(PLA), tarmarind acetate and levan acetate mircospheres were investigated. Hydrophobic tarmarind acetate and levan acetate were prepared by chemical modification of hydrophilic tarmaried gum and levan and microspheres were made by a solvent evaporation method. In the case of poly(L-lactic acid) microspheres, drug release rate was effected by polymer-drug ratios and drum release was sustained by increasing of polymer content. The yield of microspheres were effected by many factors and the mean size was below 1 $\mu$m, The IND release profiles from tarmarind acetate and levan acetate micropheres were more slightly less than ploy(L-lactic acid) microspheres.