• 동력기계공학회지
• /
• 제21권6호
• /
• pp.56-61
• /
• 2017

The check valves are mechanical valves that permit fluids to flow in only one direction, preventing flow from reversing. It is classified as one way directional valves. There are various types of check valves that used in a marine application. A lift type check valve uses the disc to open and close the passage of fluid. The disc lift up from seat as pressure below the disc increases, while drop in pressure on the inlet side or a build up of pressure on the outlet side causes the valve to close. An important concept in check valves is the cracking pressure which is the minimum upstream pressure at which the valve will operate. On the other hand, optimization is a process of finding the best set of parameters to reach a goal while not violating certain constraints. The AMESim software provides NLPQL(Nonlinear Programming by Quadratic Lagrangian) and genetic algorithm(GA) for optimization. NLPQL is the implementation of a SQP(sequential quadratic programming) algorithm. SQP is a standard method, based on the use of a gradient of objective functions and constraints to solve a non-linear optimization problem. A characteristic of the NLPQL is that it stops as soon as it finds a local minimum. Thus, the simulation results may be highly dependent on the starting point which user give to the algorithm. In this paper, we carried out optimization design of the check valve with NLPQL algorithm.

• International Journal of Fluid Machinery and Systems
• /
• 제1권1호
• /
• pp.140-147
• /
• 2008

An experiment setup was introduced to study dynamic behaviour of different types of check valves and the effects of air entrainment on the check valve performance under pressure transient condition. The experiment results show that the check valves with low inertia, assisted by springs or small traveling distance/angle gave better performance under pressure transient condition than check valves without these features. Air entrainment was found to affect both wave speed and reverse velocity. With the increase of the initial air void fraction in pipeline, the experiment results show that the wave speed was reduced, the reverse velocity was increased. The first peak pressure increased initially and then decreased with the increase of the initial air void fraction, the pressure surge periods were increased proportionally with air void fraction due to the greatly reduced wave speed. The study can be applied to help choosing suitable check valves for a particular pumping system.

• Journal of Radiation Protection and Research
• /
• 제38권2호
• /
• pp.119-123
• /
• 2013

HPGe 검출기를 사용하는 감마 분광분석계의 건전성을 점검하기 위한 실험실 선원이 개발되었다. 점검 선원은 0.154 mm 이하의 라듐이 풍부한 토양을 밀봉된 원통형 시료 용기에 담은 것으로, 검출기 교정에 사용할 12 개의 감마선이 방출된다. 점검 선원의 스펙트럼은 1년 동안 1개월 간격으로 측정하였으며, 스펙트럼에 나타난 감마선 피크들의 특성을 조사하였다. 감마 분광분석계가 정상일 때 라듐과 그 붕괴 생성물에서 3% 이상 방출률을 갖는 감마선들의 피크면적과 반치폭은 77 keV 피크를 제외하고는 각각 표준편차 2%와 3% 이내에서 일정하였다. 따라서 점검 선원은 77 keV부터 2202 keV까지 영역에 있는 10개의 피크를 사용하여 분광분석계의 건전성을 점검하는데 충분한 것으로 판단되었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 학술대회 논문집 정보 및 제어부문
• /
• pp.49-51
• /
• 2004

This paper presents a realization of fault detection algorithm and Fieldbus based communication for condition monitoring of check valve. We first acquired the AE(Acoustic Emission) sensor data at the KAERI check valve test loop, extract fault features through the learned Neural network, and send the processed data to a remote site. The overall system has been implemented and experimental results are given to show its effectiveness.

• 한국주거학회논문집
• /
• 제21권1호
• /
• pp.103-112
• /
• 2010

This Study is about the check-List composition for 'Low carbon green growth' of Long-life housing. That utilization for required the check-list composition at Sustainable building strategies and Design methods. That for long life housing, sustainable building strategies part of building construction and interior, the proper foundation for legislative system, maintenance methods with in building life cycle, sustainable and green architecture capability realization prepare for connection plan with 'Low carbon-green growth'. Extracting from elements of Architectural planing answer to basic concept of Low carbon-green growth and aimed at Low carbon scheme for energy saving, green growth scheme for environmental conservation as to each application purpose reconstitute by classify Check-list category about elements of Architectural planing. Through this architectural research deduce elements of architectural planing that can be research utilization with in Check-list composition.

• 항공우주시스템공학회지
• /
• 제12권2호
• /
• pp.7-14
• /
• 2018

본 연구에서는 소형 압전유압펌프가 적용된 브레이크 시스템의 부하압 개선을 위해 체크밸브에 대한 연구를 수행하였다. 가압 과정에서 부하의 정상상태 압력은 챔버압과 부하압이 체크밸브에 작용하는 단면적 비에 영향을 받는다. 체크밸브 유로 덮개는 역류 방지를 위해 유로의 단면적보다 넓게 제작되었기 때문에 단면적 비 조절을 위해 박판 스프링 형 체크밸브에 부가질량을 부착하는 방식을 제안하였다. 부가질량 부착에 의한 부하압 개선 효과를 확인하기 위해 상용코드를 이용하여 소형 압전유압펌프가 적용된 단순 브레이크 시스템의 모델링을 수행하였다. 모델링의 검증을 위해 부가질량이 부착되지 않은 박판 스프링 형 체크밸브를 적용한 펌프의 가압 실험결과와 시뮬레이션 결과를 비교하였다. 검증된 아메심 모델링에 부가질량을 추가하였고 시뮬레이션을 통해 단면적 비 조절에 의한 고 부하압 형성 효과를 확인하였다. 부가질량 추가에 따른 소형 압전유압펌프 구성품을 새롭게 설계/제작한 후 브레이크 시스템의 가압 성능 실험을 수행하여 부하압 35% 의 성능 개선을 확인하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.529-533
• /
• 1996

Recently, manufacturing industries are doing their best to increase productivity and to reduce production time. One of tile efforts is to develop user-friendly and effective CAM systems. For this purpose, a CAM system for turning was developed. In the developed system. user interacts with tile CAM system using graphical user interface (GUI) and manufacturing support functions to make NC programs effectively. Manufacturing support functions include cycle decoder. interference check be ween tool and workpicce. bar turning without air cut and dynamic/wireframe simulation. In the cycle decoder. basic options are provided to novices for their convenience. and advanced options are provided to help expert to modify the program using their knowledge. Interference check has been nil issue in tile CAM system for tuning. In this paper. when a user selects a tool. interference check between selected tools and workpieces is done automatically. Moreover. remaining shapes are calculated automatically. Then, tile CAM system requests user to input all additional tool and generates NC codes to cut tile remaining shapes. In bar turning of forged raw material, air cut should be prevented for effective machining. For this purpose, a new algorithm for bar turning was developed. Dynamic and wireframe simulation was used to verify the generated NC code.

• 한국가스학회:학술대회논문집
• /
• 한국가스학회 2005년도 추계학술발표회 논문집
• /
• pp.59-65
• /
• 2005

• 한국산업경영시스템학회:학술대회논문집
• /
• 한국산업경영시스템학회 2002년도 춘계학술대회
• /
• pp.403-412
• /
• 2002

Machine condition diagnosis is the technique to perceive the machine errors and the abrasion online without overhaul. We need the steps to predict the life span and reliability of a machine for the abrasion as with perceiving the degree of the abrasion of certain machine parts to make errors. In this study we deals with the methods to check and manage periodically and to configure the judgement criteria for the state of a machine. For the applications of CDT(Condition Diagnosis Technique) we also suggest the methods to check comparing the measured vibration values with the absolute criteria and to check the abnormality by vibration level.

• Journal of Electrical Engineering and Technology
• /
• 제11권5호
• /
• pp.1084-1092
• /
• 2016