• Journal of Aerospace System Engineering
• /
• v.12 no.5
• /
• pp.32-39
• /
• 2018

In this paper, the calculation of the theoretical pressure transfer ratio due to the deformation of the thin-plate spring type check valve applied to the small piezoelectric-hydraulic pump was carried out. A thin-plate check valve is a flexible body that is deformed by an external force. The deformation of the check valve affects the rate at which the chamber pressure is transferred to the load pressure. The theoretical pressure transfer ratio for each model was calculated to compare the difference between the assumption that the thin-plate check valve is a rigid body and that of the flexible body model. The P-delta effect was considered for the calculation of the pressure transfer ratio of the flexible check valve model. In addition, a verification test for the calculated pressure transfer ratio obtained by considering the deformation of the flexible check valve model was carried out. The load pressure was measured by applying a thin-plate and ball-thin plate spring type check valves, respectively. The experimental pressure transfer ratio was calculated using the respective load pressure obtained from the experiments. The validity of the pressure transfer analysis of the check valve, taking into consideration the P-delta effect, was verified by comparing it with the theoretically calculated pressure transfer ratio.

• Journal of Aerospace System Engineering
• /
• v.11 no.1
• /
• pp.41-46
• /
• 2017

A new test bench for small multi-rotor type drones has been developed. Six degrees of freedom (DOF) motion is possible due to a ball bushing, wheels, and rotating plates. An FPGA (field programmable gate array) based controller, that supports realtime parallel processing, is used to measure attitude with an accelerometer and a gyro to adjust motor speed. Several tests were performed to check the operational properties of the test bench and the controller. The results show that this test bench is proper for verifying controllers and the control methods of small multi-rotor drones.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.3
• /
• pp.274-281
• /
• 2013

Field measurement method of heavy/soft impact sound pressure level which is regulated in JIS and ISO has been using in Korea, Japan and Canada. It is reported that heavy/soft impact sound pressure level was varied by the sound field condition of receiving room such as sound absorption power and room volume. In this study, it is checked that heavy/soft impact sound pressure level was affected by the receiving sound field condition. Rubber ball and bang machine sound pressure level was measured in the vertically connected reverberation chamber. In oder to check the effect of receiving sound field on heavy/soft impact sound pressure, sound absorption power was changed with polyester sound absorption blankets with air space and glass wool. The reverberation time at 1 kHz band was changed from 10 s to 0.2 s by sound absorption material. Rubber ball sound pressure level measured without sound absorption material was 58 dB in $L_{i,Fmax,AW}$, but the level was 46 dB with sound absorption treatment. From this result, it is confirmed that sound field correction method is needed in the heavy/soft impact sound pressure level measurement method using bang machine and rubber ball.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.12
• /
• pp.52-59
• /
• 2004

This paper shows about the machine simulation embodiment when it happens NC equipment and between workpiece and interference in 5 axises machining of aluminium alloy a vehicles parts. And this research has been chosen because of the highest equipment interference occurrence rate at a vehicles parts processing of 5 axises horizontal machine. It can verify simulation and machining process through correlation of their dynamic relations, interference, collision as embodied virtual manufacturing system of machine, workpiece, and holder etc. That is necessary element in shape of machine tool, function and processing in imagination ball. Also, it verifies about interference and collision between NC equipment and workpiece, as it applied machine simulation to NC Data of actuality aircraft parts of BULKHEAD and FRAME. As the result of this study, by removing the equipment interference and collision element which creates NC data, the virtual machine tool it the efficiency of machine process has increased.

• 한국전산유체공학회:학술대회논문집
• /
• 2005.10a
• /
• pp.219-222
• /
• 2005

Recently, the interest of the engine capacity and environment of the atmosphere is increasing, so the researches for the engine capacity have been conducted for a long time. But the internal environment of an automotive engine is very severe. A piston is exposed to combustion gas of over $2000^{\circ}C$ and strong friction is occurred by high speed motion in the cylinder. The fraction between piston and wall of the cylinder causes the increase of temperature in the engine. The temperature of the engine has an effect on the engine capacity. If the temperature is high, the capacity of the engine is low. So we have to maintain the optimum temperature. To maintain the optimum temperature, the enough flow rate of the engine oil is needed. The oil jet is used to control the flow rate of the engine oil and supply the engine oil to the piston and cylinder. The purpose of this study is to check the mass flow rate of the engine oil and the characteristics of internal flow of the oil jet. Flow pattern of the engine oil is very important because it concludes the loss in the oil jet. This study is the previous research about the oil jet and we will consider the movement of the ball check valve to get more accuracy result.

• The Pure and Applied Mathematics
• /
• v.25 no.1
• /
• pp.49-57
• /
• 2018

We have introduced two new notions of convexity and closedness in functional analysis. Let X be a real normed space, then $C({\subseteq}X)$ is functionally convex (briefly, F-convex), if $T(C){\subseteq}{\mathbb{R}}$ is convex for all bounded linear transformations $T{\in}B$(X, R); and $K({\subseteq}X)$ is functionally closed (briefly, F-closed), if $T(K){\subseteq}{\mathbb{R}}$ is closed for all bounded linear transformations $T{\in}B$(X, R). By using these new notions, the Alaoglu-Bourbaki-Eberlein-${\check{S}}muljan$ theorem has been generalized. Moreover, we show that X is reflexive if and only if the closed unit ball of X is F-closed. James showed that for every closed convex subset C of a Banach space X, C is weakly compact if and only if every $f{\in}X^{\ast}$ attains its supremum over C at some point of C. Now, we show that if A is an F-convex subset of a Banach space X, then A is bounded and F-closed if and only if every element of $X^{\ast}$ attains its supremum over A at some point of A.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.9 no.5
• /
• pp.7-13
• /
• 2010

Main starting valve is one of the main parts in the control system of diesel engines, purposed for starting main engines. It is composed of ball valve, check valve, actuator, etc. The design axioms provide a general framework for design methodology. Two axioms are independence axiom and information axiom. These axioms can be applied to all design process in a general way. The first axiom is introduced to analyze and evaluate the design of a main starting valve. The design parameters(DPS) are determined sequentially by considering the independence axiom. For the structural design of a main starting valve, the strength is calculated by using finite element method. In addition, the strength of its actuator piston is evaluated.

• Journal of the Society of Naval Architects of Korea
• /
• v.31 no.3
• /
• pp.129-134
• /
• 1994

A Laser Cutter is designed for the precise fabrications in the shipyards recently. The cutter is a gantry type one with specified functions of movability and strength in order to satisfy the workability. The gantry frame should move with a certain velocity in a relatively short time for the proper cutting of the object materials. The gantry is fitted with ball screw and the acceleration field is formed by actuating this ball screw. The relative displacement should be within the allowable design criteria to make sure the precise cutting of the materials by the laser. In this paper, modal and structural analysis for a Laser Cutter which is commonly used in the shipyards, is carried out to check the design criteria of the system. The system is modeled by placing the proper shell and soils finite elements and fictitious mass properties to represent the real one. The way how to extract the loading conditions based on the given velocity criteria of the system is presented. Static structural analysis is performed and the results came out as expected. Modal analysis for finding eigen-values and mode shapes of the system is performed and it is shown that the time dependent dynamic analysis is unnecessary for this system for its operating circumstances.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.9 no.1
• /
• pp.49-54
• /
• 2010

An integrated machining center is developed for high precision and productivity manufacturing. The developed machine is composed of the high precision spindle using ball bearings, the high stiffness bed and the three axis CNC controller with the high resolution AC servo motor. In this paper, structural and modal analysis for the developed machine are carried out to check the design criteria of machine. The analysis is carried out by FEM simulation with using the commercial software, CATIA V5, ANSYS and ARMD. The simulation model of machine is made by shell and solid finite elements. This study also presents the measurement system on the modal analysis of an integrated machining center. The weak part of the machine is found by the analytical evaluation. The results provide with the structural modification data for good dynamic behaviors. And the safety of machine is confirmed by the modal analysis of modified machine design. As this study results can be trustworthy with the analysis of ANSYS and CATIA, integrated machining center can be successfully developed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.5
• /
• pp.771-777
• /
• 2006

Recently regulations which make it mandatory to use the environment-friendly goods are increaing in automobiles. In this study the TIG autogenous welding process was developed by solving the problem of previous spot welding of side part and the ceramic protection Jig was developed for the welding of fragile glass ball. And the optimal process parameter was selected by complementing the demerit of the previous filler material welding to fill up the bottom part. Finally the lamp aging test and earthquake resistant test was done to check the reliability of welded brake lamp.