• Journal of Advanced Marine Engineering and Technology
• /
• 제18권2호
• /
• pp.75-82
• /
• 1994

The existence of peroodic impulse noises in distribution line carrier (DLC) communication system is known to be the most serious obstacle for improving DLC communication quality in reliability and capacity. From the spectral points, impulse noises can be divided into baseband type and modulation type the noise width of whichs are much different each other. With each nose type, this study presents the basic characteristics in relation to what they originate from and how their spectrum properties are revealed. The baseband type impulse noise is normally caused from thyristor circuit running with low switching speed and the modulation type noise from the circuit of switching power supply. The base wave of modulation noise is shown to be the pulsuatic charging current to primary condenser in switching power circuit. The study result indicates also that placing the DLC carrier frequency away the band predominated by modulated noise especially from RCC type switching power circuit is very important in DLC design.

• 대한기계학회논문집B
• /
• 제29권7호
• /
• pp.795-804
• /
• 2005

As the flying height of a slider in a hard disk drive decreases, the slider and disk are more likely to come in contact and generate contamination particles. Since particle contamination can cause serious problems including thermal asperity, it must be prevented to increase storage capacity. When particles are generated in a HDD, particles can be charged and have a few number of elementary charges. In this paper, the size distribution of particles and electrical current due to particle according to the disk rotational speed were measured. Also, the average number of elementary charges was calculated from experimental data. SEM images of particles were obtained by using a particle sampler designed in our laboratory.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2002년도 전력전자학술대회 논문집
• /
• pp.489-493
• /
• 2002

This paper discover another boost vectors in high modulation index In steady states, modulation index of converter operation is normally $0.7\~0.8[p.u]$. Even though zero vectors are not imposed, DC-Link voltage is constant because 3-level boost convert has another boost vectors. and this paper proposes the analysis and the comparison for NPC and H-Bridge converter. It proposed the calculation method for the voltage ripple and charging current of each capacitor and deals with voltage balance problems of each link capacitor they are associated with the switching state, the position of reference voltage vector. Simulation and analysis are used in order to prove validity of the proposed methods.

• 전력전자학회논문지
• /
• 제5권6호
• /
• pp.537-543
• /
• 2000

표준 배터리 모듈 시스템을 위한 새로운 배터라 충.방전기를 제안한다. 전체 시스템의 크기를 줄이기 위해 충전기와 방전기의 회로가 하나의 컨버터로 구현되었으며, 최대 전력 추적을 포함한 태양전지 출략전압 제어와 태양 전지 출력과 부하 전력에 따른 배터리 충.방전 전류 제어를 동시에 수행한다. 또한, 제안된 컨버터는 부하의 전략 공급을 간단히 할 수 있는 일성 전압 버스(regulated bus)를 제공한다. 제안된 컨버터는 특성상 DCM으로 동작하므로 전듀의 첨두지가 크므로 고전력 시스템에서는 여러 개의 모듈로 사용되어야 한다.

• Journal of Power Electronics
• /
• 제18권3호
• /
• pp.910-922
• /
• 2018

Conventional battery state-of-charge (SoC) estimation methods either involve sophisticated models or consume considerable computational resource. This study constructs an enhanced coulomb counting method (Ah method) for the SoC estimation of lithium-ion batteries (LiBs) by expanding the Peukert equation for the discharging process and incorporating the Coulombic efficiency for the charging process. Both the rate- and temperature-dependence of battery capacity are encompassed. An SoC mapping approach is also devised for initial SoC determination and Ah method correction. The charge counting performance at different sampling frequencies is analyzed experimentally and theoretically. To achieve a favorable compromise between sampling frequency and accumulation accuracy, a frequency-adjustable current sampling solution is developed. Experiments under the augmented urban dynamometer driving schedule cycles at different temperatures are conducted on two LiBs of different chemistries. Results verify the effectiveness and generalization ability of the proposed SoC estimation method.

• 센서학회지
• /
• 제21권5호
• /
• pp.379-384
• /
• 2012

This paper presents the power source of wireless sensor node (WSN) using supercapacitors and a solar cell. Supercapacitors have high lifetime cycling compared to that of batteries. Supercapacitors are connected in series to achieve higher voltage and a voltage balancing circuit is required to ensure that no individual cell goes overvoltage. We employ an active balancing circuit that draws minimal current by using transistors. A diode is connected in series with each supercapacitor. A new balancing circuit that equalize the cells-voltage reduces energy consumption of supercapacitors. Voltage of operating WSN is applied 2.2-3.3V by DC/DC converter and supercapacitor voltage 2.2-5.1V. Maximum operating time of wireless sensor node is about 16 hours in full charging.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2000년도 제1회 학술대회 논문집
• /
• pp.49-50
• /
• 2000

5.2" microtip field emission displays (FEDs) with high voltage applications are fabricated. Nano-structural analysis on microtips is performed for the reliable operation of FEDs. Chemical compositions on the apex of microtips are fully analyzed. A charging mechanism on spacers is simulated and experimentally confirmed with micro-images. A gas-aging mechanism is also studied with integration step of FEDs. The brightness of more than 300 $cd/m^2$ is achieved. In addition, as a new concept, 9" color carbon nanotube FEDs (CNT-FEDs) are introduced using well-aligned carbon nanotubes on glass substrates by paste squeeze and surface treatment techniques. A number of carbon nanotubes, $5-10/{\mu}m2$, are uniformly distributed over a large area. The turn-on fields of 1 $V/{\mu}m$ and field emission currents of 1.5 mA at 3 $V/{\mu}m$ are acquired. Different mechanisms between microtip FEDs and CNT-FEDs are discussed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 F
• /
• pp.2054-2056
• /
• 1998

A conventional UPS can supply the clean power to the load. However, it may generate input current harmonics and the input power factor can be very poor. Therefore, the UPS itself may be a power interruption. This paper provides multifunctional converter of using single phase UPS. The proposed UPS can supply the clean power to the load without polluting the mains power system. The multi-functional converter provides battery charging, var compensation and harmonic suppression simultaneously. It was simulated to verify this work.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 E
• /
• pp.1816-1818
• /
• 1997

A triggered sparkp gap switch was fabricater and its high-voltage discharge characteristics were studied. The switch is composed of two main electrodes and one trigger electrode which is placed perpendicular to the main one. Spark gap distance was fixed by 25 mm. This device has been operated without self firing at the pulse repetition frequency from 1 to 20 Hz limited by the charging current, and the hold-off voltage from 10 to 30kV. An IGBT switch and igniter coil (originally used in a car) were adopted for a trigger circuit. In this article preliminary switch characteristics of the spark gap switch are reported with the emphasis on the description of the trigger circuit.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 E
• /
• pp.1681-1683
• /
• 1997

Linear induction accelerator devised for high current beam accelerating is divided into two types. In the first type, a unidirectional pulse is injected to an accelerating gap and in the second type, a bidirectional pulse is injected. The purpose of this paper is design and manufacture of bidirectional pulse generator for linear induction accelerator, where the pulse width for acceleration is more than 50[nsee] and the designed maximum charging voltage is more than 200[kV].