• 한국군사과학기술학회지
• /
• 제19권3호
• /
• pp.339-345
• /
• 2016

This paper is concerned with the numerical simulation result of pressure propagation to the main charge by warhead penetration into concrete targets. In this study, we developed on-line pressure measurement method in the main charge during warhead penetration. Using the on-line pressure measurement method, we successfully recorded the pressure-time history in the main charge during the field penetration test. Then we compared result of numerical simulations with test data and found that the simulation results are in good agreement with the test results. Finally, through the numerical calculations it is concluded that the installation of liner is effective in reducing pressure level produced in the main charge.

• 한국전산구조공학회논문집
• /
• 제32권2호
• /
• pp.133-140
• /
• 2019

본 논문은 Shaped charge jet(SCJ)의 관통 과정을 유한요소해석을 통해 모사하여 제트 입사속도, 관통률 그리고 관통량 증분과 같은 물리량들을 획득하였다. 이 물리량들을 hydrodynamic 이론에 적용하여 입사 제트 속도의 효율을 분석한 결과, 입사 속도가 빠른 제트의 관통 효율은 이어지는 느린 제트에 비해 높은 것을 확인하였다. 이 효율은 hydrodynamic limit(HL) 미만인 제트인 경우 큰 폭으로 감소하였다. 한편, 시간에 따른 관통량 증분과 제트 소모량의 비교는 SCJ의 이론적인 관통현상 분석을 위해서는 길이 연장 효과를 고려해야함을 보였다.

• 한국군사과학기술학회지
• /
• 제18권5호
• /
• pp.566-573
• /
• 2015

The most important factor for the penetration performance of shaped charge is the liner design. By designing the liner to have properties of both high jet tip velocity and long jet break-up time, the better penetration performance could be acquired. Usually it is very difficult to satisfy above two conditions simultaneously. In this study, the liner with the shape of ogive was developed to have relatively larger jet mass compared to the conventional trumpet liner. The designed shaped charge showed jet properties with high jet tip velocity and long jet break-up time by using ogive liner and wave shaper. A commercially available hydro-dynamic code AUTODYN-2D was used for numerical analysis of jet formation. The flash X-ray test and the static penetration test were conducted to verify the results of numerical analysis.

• 한국항공우주학회지
• /
• 제47권6호
• /
• pp.397-404
• /
• 2019

항공우주시스템에서 절단/분리 시스템에 널리 사용되는 선상성형장약은 복합화약 충전량의 불균일로 인해 과량의 복합화약을 충전해야 하며 제작 공정의 특성상 라이너 및 복합화약 형상을 자유자재로 조절하기 어렵다는 단점을 가지고 있다. 이를 개선하기 위하여 라이너를 단독으로 제작하여 균일한 복합화약량을 충전할 수 있는 정밀선상성형장약에 대한 연구 개발이 진행되고 있다. 본 연구에서는 정밀선상성형장약이 적정 복합화약량을 갖도록 설계하고 설계된 정밀선상성형장약의 최적 침투 관통 성능을 확인하기 위하여 라이너로부터 표적까지의 거리에 단차를 두어 이격거리에 따른 침투 관통 성능시험을 수행하였다. 정밀선상성형장약의 침투 관통 성능시험 결과를 바탕으로 AUTODYN 기반의 수치 해석 환경을 구축하였다. 수치해석 및 시험 결과의 비교 분석을 통해 정밀선상성형장약의 침투 관통 메커니즘과 특성을 분석하였다.

• The Korean Journal of Ceramics
• /
• 제5권3호
• /
• pp.270-277
• /
• 1999

The ballistic capability of an alumina-rich oxide armor ceramic against a shaped jet was characterized as a function of penetration depth in a layered target structure. The penetration resistance of the ceramic, based upon the determination of penetration velocity, was not equally realized throughout the depth of penetration. It was abnormally low at an early stage of penetration, followed by a sudden increase to reach ~16GPa thereafter. There was no apparent change in such a profile with respect to the lateral size of the specimen. Based upon 2-D flash x-ray radiography and 3-D Hull code simulation, the feasibility of forming a pressure-induced predamnaged zone in front of the jet tip was speculated to foster an increased penetration velocity in the initial stage penetration, resulting in the diminished penetration resistance. The disappearance of such a predamaged zone with penetration was interpreted to restore the resistance of the ceramic in the later penetration stage.

• Biomolecules & Therapeutics
• /
• 제19권2호
• /
• pp.231-236
• /
• 2011

The aim of this study was to investigate the effect of charge carrier lipid on the skin penetration, retention, and hair growth of topically applied finasteride-containing liposomes. Finasteride-containing liposomes were prepared by traditional thin film hydration method using Phospholipon$^{(R)}$ 85 G and cholesterol with or without charge carrier lipid (1,2 dimyristoyl-sn-glycero-3-phosphate or 1,2-dioleoyl-trimethylammonium-propane for anionic and cationic charge, respectively). Freshly prepared finasteride-containing liposome suspension was applied on the hairless mouse skin, and skin penetration and retention were measured using Keshary-Chien diffusion cell. Non-liposomal formulation (ethanol 10% solution containing 0.5 mg/ml of FNS) was also used as a control. The amount of finasteride in the diffusion cell and mouse skin was measured by HPLC. The hair growth was evaluated using depilated male C57BL/6N mice. Mean particle size of all finasteride-containing liposomes was less than a micron, and polydispersity index revealed size homogeneity. Skin penetration and retention studies showed that significantly less amount of finasteride was penetrated when applied as anionic liposome while more amount of the drug was retained. Specifically, in liposome prepared with 10% anionic charge carrier lipid, penetration was 12.99 ${\mu}g/cm^2$ while retention was 79.23 ${\mu}g/cm^2$ after 24 h of application. In hair growth study, finasteride-containing anionic liposomes showed moderate efficacy, but the efficacy was not found when applied as cationic liposomes. In conclusion, topical application of finasteride using anionic liposome formulation appears to be useful option for the treatment of androgenetic alopecia to avoid systemic side effects of the drug.

• 화약ㆍ발파
• /
• 제34권4호
• /
• pp.1-9
• /
• 2016

수중 강재 절단을 위해 내압성, 유연성의 외부장치인 스프링 호스와 가소성 성형폭약을 결합한 수중 성형폭약 장치를 고안하였다. 최적조건 설계를 위한 기초실험으로 외부장치의 형상에 따른 관입성능을 비교하였다. 실험결과를 평가하기 위하여 관입 된 강재에 액상 고무를 이용하여 모형을 획득한 후 이미지 분석을 하였고, 성형폭약의 관입 과정을 모사하기 위해 AUTODYN 프로그램을 이용하여 해석하였다. 분석결과 원형 및 사각 외부장치의 평균 관입 깊이는 유사하였으나 관입품질은 원형의 경우 더 균일하였다. 또한, 사각의 경우 침투현상이 발생하였고, 수압증가에 따른 변위가 원형대비 크게 측정되었다.

• 한국군사과학기술학회지
• /
• 제25권3호
• /
• pp.275-284
• /
• 2022

Linear Shaped Charge(LSC) is widely used as a separation system in the field of weapon system. However, there are some disadvantages that are charging lots of explosives due to lack of uniformity and having difficulties of the design of liner and explosives because of manufacturing process. In order to solve these problems, Precision Linear Shaped Charge(PLSC) that can design a liner independently and charge explosives uniformly has been developed. In this study, PLSC was designed to have a proper liner shape and amount of explosives, and the penetration test of PLSC with different stand-off distance from liner to target was conducted. On the basis of the penetration test results of PLSC, the numerical analysis method using AUTODYN was established and verified. The penetrative mechanism and characteristics of PLSC with targets of different materials was analyzed from experimental and numerical results.

• 한국군사과학기술학회지
• /
• 제18권5호
• /
• pp.574-581
• /
• 2015

In this paper, the effect of high voltage current pulse against shaped charge jet was analyzed through the visualization of jet behavior using flash X-ray and comparison of depth of penetration(DOP) into RHA(Rolled Homogeneous Armor) witness plates. The behavior of jet particles has been acquired using a flash X-ray equipment when current pulse was applied into the metal jet of a shaped charge(SC) warhead. Typical results such as jet breakup and radial jet dispersion, which are due to electromagnetic pressure by current pulse, have been obtained. Dozens of penetration experiments using a shaped charge with 55 mm diameter were performed according to various combinations of major parametric variables such as electrode spacing, standoff distance from SC warhead to electrode, and charge voltage. Subsequently, interrelations between major parametric variables and DOPs into RHA were analyzed.

• 한국시뮬레이션학회논문지
• /
• 제31권3호
• /
• pp.11-21
• /
• 2022

국과연은 물자표적에 대한 취약성 해석 모델인 AVEAM-MT(ADD Vulnerability and Effectiveness Assessment Model for Materiel Target)를 개발하고 있다. 이 모델에는 성형작약제트와 표적 간 상호작용을 해석하기 위해 두 가지 방법이 적용되었다. 그중 한 방법은 표적 부품으로 침투를 신속하게 계산하기 위해 Fireman-Pugh 방법을 개량한 경험적 모델이다. 다른 하나는 Walker-Anderson 침투모델을 성형작약제트에 적용할 수 있도록 개량한 물리기반 모델인 ADD-TSC(ADD Tandem Shaped Charge)이다. 이 논문에서는 이 두 방법을 간략히 기술하고, 경험식 방법과 물리기반 모델의 잔류침투성능 예측 결과를 비교한다. 또한 물리기반 모델이 예측한 침투성능과 문헌에서 찾은 실험 결과를 비교한다. 비교 결과는 두 방법 모두 AVEAM-MT와 같은 짧은 시간에 상당한 양의 반복적인 피해해석 시뮬레이션 수행이 요구되는 취약성 해석 모델에 탑재되어 고속 계산 또는 상대적으로 높은 충실도 계산에 유용하게 사용될 수 있음을 보인다.